Courses

# Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test)

## 65 Questions MCQ Test GATE Past Year Papers for Practice (All Branches) | Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test)

Description
This mock test of Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test) for GATE helps you for every GATE entrance exam. This contains 65 Multiple Choice Questions for GATE Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test) (mcq) to study with solutions a complete question bank. The solved questions answers in this Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test) quiz give you a good mix of easy questions and tough questions. GATE students definitely take this Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test) exercise for a better result in the exam. You can find other Instrumentation Engineering - (IN) 2018 GATE Paper (Practice Test) extra questions, long questions & short questions for GATE on EduRev as well by searching above.
QUESTION: 1

Solution:
QUESTION: 2

Solution:
QUESTION: 3

### For 0 ≤ �� ≤ 2��, sin �� and cos �� are both decreasing functions in the interval ________.

Solution:
QUESTION: 4

The area of an equilateral triangle is √3. What is the perimeter of the triangle?

Solution:
QUESTION: 5

Arrange the following three-dimensional objects in the descending order of their volumes:

(i) A cuboid with dimensions 10 cm, 8 cm and 6 cm

(ii) A cube of side 8 cm

(iii) A cylinder with base radius 7 cm and height 7 cm

(iv) A sphere of radius 7 cm

Solution:
QUESTION: 6

An automobile travels from city A to city B and returns to city A by the same route. The speed of the vehicle during the onward and return journeys were constant at 60 km/h and 90 km/h, respectively. What is the average speed in km/h for the entire journey?

Solution:
QUESTION: 7

A set of 4 parallel lines intersect with another set of 5 parallel lines. How many parallelograms are formed?

Solution:
QUESTION: 8

To pass a test, a candidate needs to answer at least 2 out of 3 questions correctly. A total of 6,30,000 candidates appeared for the test. Question A was correctly answered by 3,30,000 candidates. Question B was answered correctly by 2,50,000 candidates. Question C was answered correctly by 2,60,000 candidates. Both questions A and B were answered correctly by 1,00,000 candidates. Both questions B and C were answered correctly by 90,000 candidates. Both questions A and C were answered correctly by 80,000 candidates. If the number of students answering all questions correctly is the same as the number answering none, how many candidates failed to clear the test?

Solution:
QUESTION: 9

If �� 2 + �� − 1 = 0 what is the value of

Solution:
QUESTION: 10

In a detailed study of annual crow births in India, it was found that there was relatively no growth during the period 2002 to 2004 and a sudden spike from 2004 to 2005. In another unrelated study, it was found that the revenue from cracker sales in India which remained fairly flat from 2002 to 2004, saw a sudden spike in 2005 before declining again in 2006. The solid line in the graph below refers to annual sale of crackers and the dashed line refers to the annual crow births in India. Choose the most appropriate inference from the above data.

Solution:
QUESTION: 11

Let N be a 3 by 3 matrix with real number entries. The matrix N is such that N2 = 0. The eigen values of N are

Solution:
QUESTION: 12

Let f1(z) = z 2 and  f2 (z) = be two complex variable functions. Here z̅ is the complex conjugate of z.

Choose the correct answer.

Solution:
QUESTION: 13

X and Y are two independent random variables with variances 1 and 2, respectively. Let Z = X − Y. The variance of Z is

Solution:
QUESTION: 14

Consider two functions f(x) = (x − 2)2 and g(x) = 2x − 1, where x is real. The smallest value of x for which f(x) = g(x)  _______.

Solution:
QUESTION: 15

Consider a sequence of tossing of a fair coin where the outcomes of tosses are independent. The probability of getting the head for the third time in the fifth toss is

Solution:
QUESTION: 16

A series R-C circuit is excited by a 1∠0 V sinusoidal ac voltage source. The locus diagram of the phasor current = (x + jy) A, when C is varied, while keeping R fixed, is

Solution:
QUESTION: 17

The Thevenin equivalent circuit representation across terminals p-q of the circuit shown in the figure is a

Solution:
QUESTION: 18

A coil having an impedance of (10 + j100) Ω is connected in parallel to a variable capacitor as shown in figure. Keeping the excitation frequency unchanged, the value of the capacitor is changed so that parallel resonance occurs. The impedance across terminals p-q at resonance (in Ω) is ______.

Solution:
QUESTION: 19

Two periodic signals x(t) and y(t) have the same fundamental period of 3 seconds. Consider the signal z(t) = x(−t) + y(2t + 1). The fundamental period of z(t) in seconds is

Solution:
QUESTION: 20

Consider signal

Let �� (t) denote the unit impulse (Dirac-delta) function. The value of the integral  is

Solution:
QUESTION: 21

An ideal square wave with period of 20 ms shown in the figure, is passed through an ideal low pass filter with cut-off frequency 120 Hz. Which of the following is an accurate description of the output?

Solution:
QUESTION: 22

An input p(t) = sin(t) is applied to the system . The corresponding steady state output is y(t) = sin(t + ��), where the phase �� (in degrees), when restricted to 0° ≤ �� ≤ 360° , is ______

Solution:
QUESTION: 23

The approximate phase response of

Solution:
QUESTION: 24

Consider the transfer function . The phase margin of  G(s) in degrees is ____.

Solution:
QUESTION: 25

In the given circuit, assume that the opamp is ideal and the transistor has a β of 20. The current Io (in mA) flowing through the load ZL is ____.

Solution:
QUESTION: 26

The diodes given in the circuit are ideal. At t = 60 ms, Vpq (in Volts) is ____.

Solution:
QUESTION: 27

For the 3-bit binary counter shown in the figure, the output increments at every positive transition in the clock (CLK). Assume ideal diodes and the starting state of the counter as 000. If output high is 1 V and output low is 0 V, the current I (in mA) flowing through the 50 Ω resistor during the 5th clock cycle is (up to one decimal place) ______.

Solution:
QUESTION: 28

The representation of the decimal number (27.625)10 in base-2 number system is

Solution:
QUESTION: 29

The number of comparators required for implementing an 8-bit flash analog-to-digital converter is

Solution:
QUESTION: 30

A voltage of 6 cos(100πt) V is fed as y-input to a CRO. The waveform seen on the screen of the CRO is shown in the figure. The Y and X axes settings for the CRO are respectively

Solution:
QUESTION: 31

A 300 V, 5A, 0.2 pf low power factor wattmeter is used to measure the power consumed by a load. The wattmeter scale has 150 divisions and the pointer is on the 100th division. The power consumed by the load (in Watts) is _____ .

Solution:
QUESTION: 32

As shown in the figure, temperature θ is measured using a K type thermocouple. It has a sensitivity of 40 μV/°C. The gain (G) of the ideal instrumentation amplifier is 25. If the output Vo is 96 mV, then the value of θ (in °C) is ____.

Solution:
QUESTION: 33

A piezoelectric pressure sensor has a bandpass characteristic with cut-off frequencies of 0.1 Hz and 1 MHz, and a sensitivity of 100 mV/kPa. The sensor is subjected to a static constant pressure of 100 kPa. Its steady-state output will be

Solution:
QUESTION: 34

An amplitude modulated signal is shown in the figure. The modulation index is (up to one decimal place) ______.

Solution:
QUESTION: 35

An optical pulse containing 6 × 106 photons is incident on a photodiode and 4.5 × 106 electron-hole pairs are created. The maximum possible quantum efficiency (in %) of the photodiode is _______ .

Solution:
QUESTION: 36

Given the value of the line integral along the straight line c from (0,0,0) to (1,1,1) is

Solution:
QUESTION: 37

Two bags A and B  have equal number of balls. Bag A has 20% red balls and 80% green balls. Bag B has 30% red balls, 60% green balls and 10% yellow balls. Contents of Bags A and B are mixed thoroughly and a ball is randomly picked from the mixture. What is the chance that the ball picked is red?

Solution:
QUESTION: 38

Consider the following system of linear equations:
3x + 2ky = −2
kx + 6y = 2
Here x and y are the unknowns and k is a real constant. The value of k for which there are infinite number of solutions is

Solution:
QUESTION: 39

Consider the following equations

where p and q are constants. ��(x, y) that satisfies  the above equations is

Solution:
QUESTION: 40

In the given circuit, superposition is applied. When V2 is set to 0 V, the current I2 is -6 A. When V1 is set to 0 V, the current I1 is +6 A. Current I3 (in A) when both sources are applied will be (up to two decimal places) _____.

Solution:
QUESTION: 41

In the figure, an RLC load is supplied by a 230 V, 50 Hz single phase source. The magnitude of the reactive power (in VAr) supplied by the source is ________.

Solution:
QUESTION: 42

In the given circuit, the mesh currents I1, I2 and I3 are

Solution:
QUESTION: 43

The Fourier transform of a signal x(t), denoted by X(jω), is shown in the figure.

Let The value of Fourier transform of y(t) evaluated at the angular frequency ω= 0.5 rad/s is

Solution:
QUESTION: 44

Let , where ∗ denotes convolution and x[��] and ℎ[��] are two discrete time sequences. Given that the z-transform of  the z-transform of is

Solution:
QUESTION: 45

f or the sequence x[��] = {1, −1,1, −1}, with �� = 0,1,2,3, the DFT is computed as   , for k = 0,1,2,3. The value of k for which X(k) is not zero is

Solution:
QUESTION: 46

Consider the standard negative feedback configuration with  and  The number of clockwise encirclements of (−1,0) in the Nyquist plot of the Loop transfer-function   G(s)H(s) is _____

Solution:
QUESTION: 47

Consider the linear system   , with initial condition
The solution x(t) for this system is

Solution:
QUESTION: 48

Consider a standard negative feedback configuration with and

For the closed loop system to have  poles on the imaginary axis, the value of  �� should be equal  to (up to one decimal place)_____.

Solution:
QUESTION: 49

Unit step response of a linear time invariant (LTI) system is given by  . Assuming zero initial condition, the transfer function  of the system is

Solution:
QUESTION: 50

In the given relaxation oscillator, the opamps and the zener diodes are ideal. The frequency (in kHz) of the square wave output vo is _____.

Solution:
QUESTION: 51

An opamp that is powered from a ± 5V supply is used to build a non-inverting amplifier having a gain of 15. The slew rate of the opamp is 0.5X106 V/s. For a sinusoidal input with amplitude of 0.3 V, the maximum frequency (in kHz) up to which it can be operated without any distortion is (up to one decimal place) ___.

Solution:
QUESTION: 52

The circuit given uses ideal opamps. The current I (in mA) drawn from the source vs is  (up to two decimal places) ____.

Solution:
QUESTION: 53

The product of sum expression of a Boolean function F(A, B, C ) of three variables is given by

The canonical sum of product expression of F(A, B, C ) is given by

Solution:
QUESTION: 54

A 2-bit synchronous counter using two J-K flip flops is shown. The expressions for the inputs to the J-K flip flops are also shown in the figure. The output sequence of the counter starting from Q1Q2 = 00 is

Solution:
QUESTION: 55

A portion of an assembly language program written for an 8-bit microprocessor is given below along with explanations. The code is intended to introduce a software time delay. The processor is driven by a 5 MHz clock. The time delay (in ms) introduced by the program  is _______.
MVI B, 64H  ; Move immediate the given byte into register B. Takes 7 clock periods.
LOOP : DCR B  ; Decrement register B. Affects Flags. Takes 4 clock periods.
JNZ LOOP    ; Jump to address with Label LOOP if zero flag is not set. Takes 10 clock periods when jump is performed and 7 clock periods when jump is not performed.

Solution:
QUESTION: 56

The Boolean function F( X, Y) realized by the given circuit is

Solution:
QUESTION: 57

The voltage and current drawn by a resistive load are measured with a 300 V voltmeter of accuracy ± 1% of full scale and a 5 A ammeter of accuracy ± 0.5% of full scale. The readings obtained are 200 V and 2.5 A. The limiting error (in %) in computing the load resistance is (up to two decimal places) ____.

Solution:
QUESTION: 58

A high Q coil having distributed (self) capacitance is tested with a Q-meter. First resonance at ω1 = 106 rad/s is obtained with a capacitance of 990 pF. The second resonance at ω​2 = 2 X106 rad/s is obtained with a 240 pF capacitance. The value of the inductance (in mH) of the coil is (up to one decimal place) ______.

Solution:
QUESTION: 59

The inductance of a coil is measured using the bridge shown in the figure. Balance (D = 0) is obtained with C1 = 1 nF, R1 = 2.2 MΩ, R2 = 22.2 kΩ, R4 = 10 kΩ. The value of the inductance Lx (in mH) is ______.

Solution:
QUESTION: 60

The average velocity v of flow of clear water in a 100 cm (inner) diameter tube is measured using the ultrasonic flow meter as shown in the figure. The angle q is 45°. The measured transit times are t1 = 0.9950 ms and t2 = 1.0000 ms. The velocity v (in m/s) in the pipe is (up to one decimal place) ___.

Solution:
QUESTION: 61

A 1000 W strain gage (Rg) has a gage factor of 2.5. It is connected in the bridge as shown in figure. The strain gage is subjected with a positive strain of 400 mm/m. The output Vo (in mV) of the bridge is (up to two decimal places) _____.

Solution:
QUESTION: 62

Assuming ideal opamp, the RMS voltage (in mV) in the output Vo only due to the 230 V, 50 Hz interference is (up to one decimal place) _____.

Solution:
QUESTION: 63

The sampling rate for Compact Discs (CDs) is 44,000 samples/s. If the samples are quantized to 256 levels and binary coded, the corresponding bit rate (in bits per second) is _____.

Solution:
QUESTION: 64

A Michelson Interferometer using a laser source of wavelength ��0 = 500 nm, with both the mirrors (��1& ��2) fixed and positioned equidistant from the splitter/combiner is shown in the figure. When a dielectric plate of refractive index �� = 1.5, of thickness �� , is placed in front of the mirror  ��2 , a dark fringe is observed on the detector. When the dielectric plate is removed without changing the position of the mirrors ��1& ��2, a bright fringe is observed on the detector. The minimum thickness �� (in nm) of the dielectric is ________.

Solution:
QUESTION: 65

A multi-mode optical fiber with a large core diameter has a core refractive index ��1 = 1.5 and cladding refractive index ��2 = 1.4142. The maximum value of ���� (in degrees) for which the incident light from air will be guided in the optical fiber is ______.

Solution: