Description

This mock test of Test: Electrical And Electronic Measurements- 7 for Electrical Engineering (EE) helps you for every Electrical Engineering (EE) entrance exam.
This contains 10 Multiple Choice Questions for Electrical Engineering (EE) Test: Electrical And Electronic Measurements- 7 (mcq) to study with solutions a complete question bank.
The solved questions answers in this Test: Electrical And Electronic Measurements- 7 quiz give you a good mix of easy questions and tough questions. Electrical Engineering (EE)
students definitely take this Test: Electrical And Electronic Measurements- 7 exercise for a better result in the exam. You can find other Test: Electrical And Electronic Measurements- 7 extra questions,
long questions & short questions for Electrical Engineering (EE) on EduRev as well by searching above.

QUESTION: 1

A voltage signal V(t) = A + B sin ωt is fed to an oscilloscope with the coupling mode set to DC, other settings being appropriate. The displayed wave can be expressed as

Solution:

When a voltage signal is fed to an oscilloscope with DC coupling entire waveform will be displayed including the DC component.

QUESTION: 2

Calculate the ratio of vertical to horizontal frequencies for an oscilloscope which display the following Lissajous figure.

Solution:

Ratio of the two frequencies is

*Answer can only contain numeric values

QUESTION: 3

A sinusoidal waveform, when observed on an oscilloscope, has a peak to peak amplitude of 4 cm. If the vertical sensitivity setting is 7.5 V/cm, the rms value of the voltage is__ (in V)

Solution:

Vertical voltage sensitivity = 7.5 V/cm

Peak to peak voltage = 7.5 × 4 = 30 V

Maximum voltage = 15 V

Rms value of the voltage = 15/√2 = 10.6 V

QUESTION: 4

A single channel analog oscilloscope is operated in X-Y mode. An ellipse rotating in anticlockwise direction and having major axis in 2^{nd} and 4^{th}quadrants displayed on the screen. The peak Y deflection is at 5 divisions and Y intercept is at 3 divisions. The phase difference between both the input signals is ______

Solution:

QUESTION: 5

An electrostatically deflected CRT has plane parallel deflecting plates which are 2.5 cm long and 0.5 cm apart. The distance of the screen form the center of the plates is 20 cm. The accelerating voltage is 2500 V. The deflecting voltage required to get the corresponding deflection of 4 cm on the screen and the velocity of the electron beam entering the field respectively are.

Solution:

Given that y = 4 cm

D = 2.5 cm

L = 20 cm

d = 0.5 cm

V_{a} = 2500 V

QUESTION: 6

In an analog single channel cathode ray oscilloscope (CRO), the x and y sensitivities are set as 1ms/div. and 1V/div. respectively. The y-inputs is connected to a voltage signal 4 cos (200 πt – 45°) V. The trigger source is internal, level chosen is zero and the slope is positive. The display seen on the CRO screen is

Solution:

Input = 4 cos (200 πt – 45°)

Peak voltage = 4 V

Y sensitivity = 1V/div

No of divisions on y – axis = 4/1 = 4

ω = 200π

2π f = 200π

⇒ T = 1/100 = 10 ms

X sensitivity = 1ms/div

No. of x – divisions = 10/1 = 10 for one full cycle

The trigger is set to zero

Hence waveform starts from zero.

QUESTION: 7

The input impedance of a CRO is equivalent to a 1 MΩ resistance in parallel with a 45 pF capacitance. It is used with a compensated 10 to 1 attenuation probe. The effective input capacitance at the probe tip is

Solution:

Given that 10 to 1 attenuation probe.

Effective input capacitance = (45 || 5)

= 4.5 pF

*Answer can only contain numeric values

QUESTION: 8

A Lissajous pattern on the oscilloscope is stationary having 8 vertical maximum values and 6 horizontal maximum values. The frequency of vertical input of the frequency of horizontal input if the frequency of horizontal input is 1800 kHz is – (in kHz)

Solution:

Given that,

Horizontal frequency (f_{H}) = 1800 kHz

Number of vertical tangencies (N_{v}) = 8

Number of horizontal tangencies (N_{H}) = 6

We know that,

f_{H}N_{H} = f_{v}N_{v}

*Answer can only contain numeric values

QUESTION: 9

The below given ellipse is displayed on the screen when a CRO is operated in x-y display mode. The phase difference between both input signals is – (in degree)

Solution:

f = 360° - f_{x} = 330°

[∵ since rotation is anticlockwise]

*Answer can only contain numeric values

QUESTION: 10

A CRO has an anode voltage 3000 V and parallel deflection plate 3 cm long and 7 mm apart. The screen is 35 cm from the centre of the plates. Find the input voltage required to deflect the beam through 4 cm. The input voltage is applied to the deflecting plates through amplifiers having an overall gain of 100.

Solution:

= 160 V

∴ Input voltage required = 160/100 = 1.6 V

- Test: Electrical And Electronic Measurements- 7
Test | 10 questions | 30 min

- Test: Electrical And Electronic Measurements- 5
Test | 10 questions | 30 min

- Test: Electrical And Electronic Measurements- 2
Test | 10 questions | 30 min

- Test: Electrical And Electronic Measurements- 4
Test | 10 questions | 30 min

- Electrical And Electronic Measurements - MCQ Test 1
Test | 10 questions | 30 min