Test: Mechanical Engineering- 10


100 Questions MCQ Test Mock Test Series for SSC JE Mechanical Engineering | Test: Mechanical Engineering- 10


Description
This mock test of Test: Mechanical Engineering- 10 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam. This contains 100 Multiple Choice Questions for Mechanical Engineering Test: Mechanical Engineering- 10 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Mechanical Engineering- 10 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering students definitely take this Test: Mechanical Engineering- 10 exercise for a better result in the exam. You can find other Test: Mechanical Engineering- 10 extra questions, long questions & short questions for Mechanical Engineering on EduRev as well by searching above.
QUESTION: 1

The heat and work are mutually convertible. This statement is called ......law of thermodynamics.

Solution:
QUESTION: 2

The amount of heat required to raise the temperature of 1 kg of water through one kelvin in called

Solution:
QUESTION: 3

A process, in which the gas is heated or expanded in such a way that the product of its pressure and volume remains constant, is called

Solution:
QUESTION: 4

In a steady flow process, the ratio of

Solution:
QUESTION: 5

The efficiency of Carnot cycle depends upon

Solution:
QUESTION: 6

In a quasi equilibrium process, the pressure in a system

Solution:
QUESTION: 7

A system and its environment put together constitute

Solution:
QUESTION: 8

The standard fixed point of thermometry is

Solution:
QUESTION: 9

In free expansion process

Solution:
QUESTION: 10

A PMM1 is

Solution:
QUESTION: 11

Compressed air coming out from a punctured football

Solution:
QUESTION: 12

The figure as shown below is the variation of the pressure of a gas with temperature (not volume) a given mass of an idea gas is subjected to various process starting from the state represented by point A. Which graph does an isochoric process represent

Solution:
QUESTION: 13

Which is usually the costliest item in a refrigeration system ?

Solution:
QUESTION: 14

COP of a domestic refrigerator in comparison to domestic air conditioner will be

Solution:
QUESTION: 15

When the lower temperature of a refrigerating machine is fixed, then the coefficient of performance can be improved by

Solution:
QUESTION: 16

The difference between dry bulb temperature ad wet bulb temperature, is called

Solution:
QUESTION: 17

The expressionis used for calculating

Solution:
QUESTION: 18

In a petrol engine, the fuel supplied to the engine cylinder is mixed with required quantity of air and the mixture is ignited with a

Solution:
QUESTION: 19

In a four stroke cycle diesel engine, the exhaust valve

Solution:
QUESTION: 20

A petrol engine, during suction stroke draws

Solution:
QUESTION: 21

The probability of knocking in diesel engines is increased by

Solution:
QUESTION: 22

The frictional power (F.P.) is given by

Solution:
QUESTION: 23

The nuclear radiators produced in a reactor which must be shielded are

Solution:
QUESTION: 24

The minimum number of rings in a piston

Solution:
QUESTION: 25

In a SI engine very high compression ratio cannot be used because

Solution:
QUESTION: 26

Lenoir cycle is used in

Solution:
QUESTION: 27

Ethyl fluid is used

Solution:

For practical purposes ethyl fluid is used to increase the octane rating of the fuel.

QUESTION: 28

Hard coke is used in

Solution:
QUESTION: 29

The incomplete combustion is indicated by the presence of

Solution:
QUESTION: 30

Efficiency of chimney draught is of the order of

Solution:
QUESTION: 31

Power required by fan in forced draught is ...... to that of induced draught

Solution:
QUESTION: 32

Rankine cycle is a

Solution:
QUESTION: 33

Which of the following component is not subjected to high-pressure high-temperature steam ?

Solution:
QUESTION: 34

Benson boiler requires

Solution:
QUESTION: 35

The amount of water evaporated in kg per kg of fuel burnt is called

Solution:
QUESTION: 36

In a glass tube type water indicator for a boiler, one end of the tube is connected to water space and the other end is connected to

Solution:
QUESTION: 37

Which of the following statement is correct ?

Solution:

Lancashire Boiler is a horizontal type and stationary fire tube boiler.

There are two types of a fire-tube boiler which are Internally & Externally fired boilers

Babcock and Wilcox Boiler was discovered by George Herman Babcock and Stephen Wilcox in the year 1967. This is a water tube boiler, used in steam power plants. In this type of boilerwater is circulated inside the tubes and hot gases flow over the tubes.

QUESTION: 38

Surface tension is due to

Solution:
QUESTION: 39

The Mercury is known as non-wetting liquid because it does not wet the surface. The Mercury posses this property due to

Solution:

Correct Answer :- a

Explanation : Capillarity is the property of both cohesion and adhesion. But surface tension is due to cohesion only it does not involve adhesion. As cohesive force is higher than adhesion in mercury it does not wet the glass.

QUESTION: 40

Which one of the following is a typical example of non-newtonian fluid of Pseudo plastic variety

Solution:
QUESTION: 41

Fluid is a substance which offers no resistance to change of

Solution:
QUESTION: 42

The continuity equation represents conservation of

Solution:
QUESTION: 43

Navier-Stoke's equation represents the conservation of

Solution:
QUESTION: 44

When the pressure intensity at a point is more than the local atmospheric pressure, then the difference of these two pressure is called

Solution:
QUESTION: 45

The point at which the resultant pressure on an immersed surface acts, is known as

Solution:
QUESTION: 46

A manometer is used to measure

Solution:
QUESTION: 47

The discharge through a venturimeter is given by

where Cd = Coefficient of discharge,
a1 = Area at inlet,
a2 = Area at throat, and
h = Venturi -head

Solution:
QUESTION: 48

Multi -stage centrifugal pumps are used to

Solution:

Correct Answer :- b

Explanation : Within a multistage centrifugal pump, each impeller acts like a single-stage pump within a chain of pumps. As the liquid is propelled from one impeller to the next within the pump’s housing, the pressure of the liquid continuously increases as it passes through until it exits the pump.

By relying on multiple impellers to distribute the pressure-building load of the pump, multistage centrifugal pumps can generate greater power and pressure with smaller motors, using less energy.

The biggest advantage of centrifugal pumps is their aforementioned simplicity. They don't require any valves, or many moving parts. This makes them easy to produce with many different materials. It also allows them to move at high speeds with minimal maintenance.

QUESTION: 49

Discharge of a centrifugal pump is

Solution:
QUESTION: 50

The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is

Solution:
QUESTION: 51

The forces, whose lines of action are parallel to each other and act in the same directions, are known as

Solution:
QUESTION: 52

Non -coplaner concurrent forces are those forces which

Solution:
QUESTION: 53

The angle of inclination of the plane at which the body begin to move down the plane is called

Solution:
QUESTION: 54

A leader is resting on a rough ground and leaning against a smooth vertical wall. The force of friction will act

Solution:
QUESTION: 55

The ratio of change in volume to the original volume is called

Solution:
QUESTION: 56

A localised compressive stress at the area of contact between two members is known as

Solution:
QUESTION: 57

The bending moment on a section is maximum where shear force is

Solution:

Correct Answer :- c

Explanation : Both zero and changes sign is the correct answer. Because when sf changes sign from max to min or vice versa, it will come to a point when sf will be zero.

So according to the given options "changes sign" is the correct answer.

QUESTION: 58

The maximum bending moment of a simply supported beam of span l and carrying a pointloadW at the centre of beam, is

Solution:
QUESTION: 59

When a body is subjected to three mutually perpendicular stresses, of equal intensity, the ratio of direct stress to the corresponding volumetric strain is known as

Solution:
QUESTION: 60

Rupture stress is

Solution:
QUESTION: 61

A material capable of absorbing large amount of energy before fracture is known as

Solution:
QUESTION: 62

Modulus of resilience is

Solution:
QUESTION: 63

 If a shaft is rotating at N revolutions per minute with an applied torque T N-m, the power being transmitted by the shaft in watt is

Solution:
QUESTION: 64

For a circular shaft of diameter d subjected to torque T, the maximum value of the shear stress
is

Solution:
QUESTION: 65

The steel bars in reinforced cement concrete beam are located at

Solution:
QUESTION: 66

A simply supported beam of span L carries a point load P at the mid span. The downward  deflection under the load will be

Solution:
QUESTION: 67

Quick return mechanics is used in

Solution:
QUESTION: 68

Oldham's coupling is the inversion of

Solution:
QUESTION: 69

A Hook's joint is used to connect

Solution:
QUESTION: 70

The cam size depends upon

Solution:
QUESTION: 71

The motion transmitted between the teeth of two spur gears is generally

Solution:
QUESTION: 72

Common contact ratio of a pair of spur pinion

Solution:
QUESTION: 73

The coriolis component of acceleration acts

Solution:
QUESTION: 74

The condition for correct steering of a Davis steering gear is

where a = Angle of inclination of the links to the vertical

Solution:
QUESTION: 75

The metal suitable for bearings subjected to light loads is

Solution:

The metal suitable for bearings subjected to light loads is phosphor bronze.

QUESTION: 76

The process which improves the machinability of steels, but lowers the hardness and tensile strength is

Solution:
QUESTION: 77

Gears are casted by

Solution:
QUESTION: 78

The ratio of endurance limit in shear to the endurance limit in flexure is

Solution:
QUESTION: 79

A thin spherical shell of internal diameter d is subjected to an internal pressure p. If st is the tensile stress for the shell material, then thickness of shell is equal to

Solution:

Correct Answer :- d

Explanation : In case of thin spherical shell hoop and longitudinal stresses are same as here length and dia are not two separate things. Both are equal. That's why when we equal resisting stress to the stress due to internal pressure same value is obtained for hoop and longitudinal.

QUESTION: 80

The centre to centre distance between two consecutive rivets in a row, is called

Solution:
QUESTION: 81

Negative rake angle is usually provided on

Solution:
QUESTION: 82

Ceramic cutting tool chip are fixed to the tool body by

Solution:
QUESTION: 83

Size of a shaper is given by

Solution:
QUESTION: 84

Which of the following is an example of rothogonal cutting ?

Solution:
QUESTION: 85

A trepanning tool is used on

Solution:
QUESTION: 86

Size of shaper is specified by

Solution:
QUESTION: 87

The soldering process is carried out in the temperature range

Solution:
QUESTION: 88

The commonly used flux for brazing is

Solution:
QUESTION: 89

Which of the following welding techniques uses a nonconsumable electrode ?

Solution:
QUESTION: 90

Oxyacetylene flame cuts metal by its

Solution:
QUESTION: 91

Silicon is added in low carbon steels to

Solution:
QUESTION: 92

A steel alloy containing 36% nickel is called

Solution:
QUESTION: 93

The sand used for making cores is

Solution:
QUESTION: 94

The purpose of a gate is to

Solution:
QUESTION: 95

A casting defect which occurs near the ingrates as rough lumps on the surface of a casting is known as

Solution:
QUESTION: 96

The acetylene cylinder is usually painted with

Solution:
QUESTION: 97

The high cutting speed and large rake angle of the tool will result in the formation of

Solution:
QUESTION: 98

Tool life is measured by the

Solution:
QUESTION: 99

The chamfering is an essential operation after

Solution:
QUESTION: 100

In electro-discharge machining, tool is made of

Solution:

Related tests