Test: Civil Engineering (SSC JE) Technical- 11


100 Questions MCQ Test Mock test series of SSC JE Civil Engineering | Test: Civil Engineering (SSC JE) Technical- 11


Description
This mock test of Test: Civil Engineering (SSC JE) Technical- 11 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam. This contains 100 Multiple Choice Questions for Civil Engineering (CE) Test: Civil Engineering (SSC JE) Technical- 11 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Civil Engineering (SSC JE) Technical- 11 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE) students definitely take this Test: Civil Engineering (SSC JE) Technical- 11 exercise for a better result in the exam. You can find other Test: Civil Engineering (SSC JE) Technical- 11 extra questions, long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.
QUESTION: 1

Radial splits in timber originating from ‘Bark’ and narrowing towards the ‘pith’ are known as

Solution:
QUESTION: 2

The most important purpose of frog in a brick is to

Solution:
QUESTION: 3

Surkhi is added to lime mortar to

Solution:

Correct Answer :- c

Explanation : Surkhi is an alternate form of sand with some additional properties of strength and hydraulicity.

QUESTION: 4

The number of bricks required per cubic metre of brick masonry is

Solution:
QUESTION: 5

Which one of the following types of concrete is most suitable in extreme cold climates?

Solution:
QUESTION: 6

The specific gravity of commonly available ordinary portland cement is

Solution:
QUESTION: 7

Which one of the following correctly expresses the split tensile strength of a circular cylinder of
length L and diameter D, subject to a maximum load of P?

Solution:
QUESTION: 8

The mix design for pavement concrete is based on

Solution:
QUESTION: 9

Which one of the following is the most preferred wood for high quality and durable furniture ?

Solution:
QUESTION: 10

The advantage in using plywood is that the

Solution:
QUESTION: 11

If ‘W’ is the percentage of water required for normal consistency of cement, water to be addedfor determination of initial setting time is

Solution:
QUESTION: 12

Which one of the following statements is correct?

Solution:
QUESTION: 13

The shear centre of a section is defined as that point

Solution:
QUESTION: 14

Match List I with List II and select the correct answer using the codes given below the lists:
 

List I
a. Moment of inertia
b. Elongation
c. neutral axis
d. Top fibre
 

List II
1. Tensile stress
2. Modulus of rupture
3. Zero shear stress
4. Zero longitudinal stress

Solution:

Correct Answer :- A

Explanation : The neutral axis is an axis in the cross section of a beam (a member resisting bending) or shaft along which there are no longitudinal stresses or strains. Therefore, the total amount of force across the cross section must be 0.

Elongation is measured by applying tensile force, or stretching the material in the same manner as described previously, and determining the change in length from original. 

The shear stress is zero at the free surfaces (the top and bottom of the beam), and it is bounded by the point of interest and the extreme fiber of the cross section.

QUESTION: 15

A thin cylindrical shell of internal diameter D and thickness t is subjected to internal pressure p.
The change in diameter is given by

Solution:
QUESTION: 16

Which one of the following shear stressN distribution diagrams is correct for cross-bar
section shown in the given figure

Solution:
QUESTION: 17

The strain energy in a member is proportional to

Solution:
QUESTION: 18

Strain energy in torsion of a shaft per unit volume is given by (q is shear stress, E —modulus of
Elasticity and G is modulus of rigidity)

Solution:
QUESTION: 19

Creep of material is a property indicated by

Solution:
QUESTION: 20

As per the elastic theory of design, the factor of safety is the ratio of

Solution:
QUESTION: 21

For the simply supported beam shown in the figure given below, at what distance from the
support A, is the shear force zero?

Solution:
QUESTION: 22

What is the correct sequence of the following metals in the decreasing order of their Poisson’s
ratio?
1. Aluminum
2. Cast iron
3. Steel

Select the correct answer using the code given below :

Solution:
QUESTION: 23

The moment capacity of section at plastic hinge equals

Solution:
QUESTION: 24

The number of independent equations to be satisfied for static equilibrium in a space structureis

Solution:
QUESTION: 25

The material in which large deformation is possible before absolute failure by rupture takesplace, is known as

Solution:
QUESTION: 26

In a plastic hinge, the actual distribution of strain across the section is essentially as

Solution:
QUESTION: 27

A correct solution of a statically indeterminate structure as per the energy method

Solution:
QUESTION: 28

Clapeyron’s theorem is applied to

Solution:
QUESTION: 29

The number of unknowns to be determined in the stiffness method is equal to

Solution:
QUESTION: 30

The allowable shear stress in the web of mild steel beams decreases with (where ‘h’ is height and t is thickness)

Solution:
QUESTION: 31

Racking force on a steel railway bridge is due to

Solution:
QUESTION: 32

Which one of the following modes of failure is taken care of in plastic design of a steel beam?

Solution:
QUESTION: 33

The type of stress induced in the foundation bolts fixing a column to its footing is

Solution:
QUESTION: 34

Which of the following does not describe a weld type?

Solution:
QUESTION: 35

A plate used for connecting two or more structural, members intersecting each other is termed as

Solution:
QUESTION: 36

In the context of the ultimate load theory for steel, the stress-strain curve for steel is idealized as

Solution:
QUESTION: 37

The sum of nodal forces at any yield line intersection in a slab is

Solution:
QUESTION: 38

In pre-tensioning scheme, pre-stress load is transferred in

Solution:
QUESTION: 39

The propagation of a shear crack in a prestressed concrete member depends on

Solution:
QUESTION: 40

Which of the following deformations are important in case of deep beams when compared to flexure alone ?

Solution:
QUESTION: 41

A structure design should

Solution:
QUESTION: 42

The failure criteria in the ultimate load method of design is

Solution:
QUESTION: 43

Partial safety factors for dead load and imposed load combination for limit state of serviceabilityare

Solution:
QUESTION: 44

In a R. C. beam shear reinforcement should be always in the form of

Solution:
QUESTION: 45

The anchorage value of a standard U-type book is equivalent to _____ times the diameter of thebar

Solution:
QUESTION: 46

Which one of the following pressure units represents the LEAST pressure ?

Solution:
QUESTION: 47

There are four variables, namely, E (volumeN modulus of elasticity), p (pressure per unit area),g (acceleration due to gravity) and 00 (viscosity of water). They are associated with mach, Euler,Froude and Reynolds numbers, respectively, in the order.

Solution:
QUESTION: 48

For laminar flow in a pipe carrying a given discharge, the height of surface roughness isdoubled. In such a case, Darcy-Weisbach friction factor will

Solution:
QUESTION: 49

Match List-I (Name of instrument) with List-II (Variable measured) and select the correct
answer using the codes given below the lists:

Solution:
QUESTION: 50

 Match List I and List II and select the correct answer using the codes given below the Lists

Solution:
QUESTION: 51

If the velocity profile in laminar flow is parabolic, then the shear stress profile must be

Solution:
QUESTION: 52

Match List I with List II and select the correct answer:

Solution:
QUESTION: 53

For a hydro-electric project with reaction turbine, the draft tube at the exit from the turbine is

Solution:
QUESTION: 54

As the depth of immersion of a vertical plane surface increases, the location of centre of pressure

Solution:
QUESTION: 55

The function of an air vessel in a reciprocating pump is to obtain

Solution:
QUESTION: 56

A fast centrifugal pump impeller has which of the following ?

Solution:
QUESTION: 57

Mean precipitation over an area is best obtained from gauged amounts by

Solution:
QUESTION: 58

Water present in an artesian aquifer is usually

Solution:
QUESTION: 59

In a linear reservoir, the

Solution:
QUESTION: 60

In the design of storm sewers, “time of concentration” is relevant to determine the

Solution:
QUESTION: 61

Self purification of running streams may be due to

Solution:
QUESTION: 62

Which one of the following principal types of reactors is related to trickling filter ?

Solution:
QUESTION: 63

A garden developed over top of surface water tank is known as

Solution:
QUESTION: 64

Rainwater of the locality which flows in sewer is called

Solution:
QUESTION: 65

Which one of the following is not a formula for determining velocity of flow in sewers

Solution:
QUESTION: 66

Which soil can take maximum dose of sewage ?

Solution:
QUESTION: 67

Land treatment of sewage is suitable when

Solution:
QUESTION: 68

Shear failure of soils takes place when

Solution:
QUESTION: 69

In a Mohr’s diagram, a point above Mohr’s envelope indicates

Solution:
QUESTION: 70

Minimum centre to centre spacing of friction pilesof diameter (D) as per BIS code is

Solution:
QUESTION: 71

Rafts resting on sands can be allowed double of the allowable soil pressure when

Solution:
QUESTION: 72

Ratio of bearing capacity of double Under Reamed (U.R.) pile to that of single UnderReamed pile is nearly

Solution:
QUESTION: 73

Influence factor for immediate settlement of footing depends on its

Solution:
QUESTION: 74

A soil has a liquid limit of 40% and plasticity index of 20%. The plastic limit of the soil will be

Solution:
QUESTION: 75

In the case of stratified soil layers, the best equation that can be adopted for computing the pressure distribution is

Solution:
QUESTION: 76

A wet, cohesive subgrade is most effectively stabilised by the addition of

Solution:
QUESTION: 77

Which one of the following soil types is most likely to be subjected to liquefaction underseismic forces?

Solution:
QUESTION: 78

The correct sequence of plasticity of minerals in soil in an increasing order is

Solution:
QUESTION: 79

Which one of the following different types of submerged soils is susceptible to liquefaction under earthquake shocks?

Solution:
QUESTION: 80

A static cone penetration test is usually conducted when the structure is likely to be founded on which of the following ?

Solution:
QUESTION: 81

For a sandy soil with soil grains spherical in shape and uniform in size, what is the theoretical void ratio?

Solution:
QUESTION: 82

Which one of the following surveys is required in observations of stars?

Solution:
QUESTION: 83

Triangulation station selected close to the main station for avoiding intervening obstruction is called

Solution:
QUESTION: 84

The process of determining the location of the station (on the map) occupied by the plane is called as

Solution:
QUESTION: 85

Diurnal variation is greater

Solution:
QUESTION: 86

Which of the following can be used as a map substitute?

Solution:
QUESTION: 87

Which one of the following is not strictly a method of remote sensing ?

Solution:
QUESTION: 88

The general requirement in constructing a reinforced concrete road is to place a single layer of reinforcement

Solution:
QUESTION: 89

For carrying out bituminous patch work during the rainy season, the most suitable binder is

Solution:
QUESTION: 90

Which one of the following is the purpose of divisional island ?

Solution:
QUESTION: 91

With addition of lime in soil

Solution:
QUESTION: 92

Match List I with List II select the correct answer using the code given below the lists:

Solution:
QUESTION: 93

Which one of the following is not a desirable property of the subgrade soil as a highway material ?

Solution:
QUESTION: 94

Guage is the distance between _____ of rails of track.

Solution:
QUESTION: 95

Narrow gauge is adopted where

Solution:
QUESTION: 96

The first railway train of the world rolled in the year

Solution:
QUESTION: 97

The length of rails used in broad gauges in India is

Solution:
QUESTION: 98

Coning of wheels is at

Solution:
QUESTION: 99

Non-corrosive material applied to rails consist of

Solution:
QUESTION: 100

On soft formation ballast material preferred is

Solution: