Test: Civil Engineering (SSC JE) Technical - 2


100 Questions MCQ Test Mock test series of SSC JE Civil Engineering | Test: Civil Engineering (SSC JE) Technical - 2


Description
This mock test of Test: Civil Engineering (SSC JE) Technical - 2 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam. This contains 100 Multiple Choice Questions for Civil Engineering (CE) Test: Civil Engineering (SSC JE) Technical - 2 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Civil Engineering (SSC JE) Technical - 2 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE) students definitely take this Test: Civil Engineering (SSC JE) Technical - 2 exercise for a better result in the exam. You can find other Test: Civil Engineering (SSC JE) Technical - 2 extra questions, long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.
QUESTION: 1

Match List-I with List-II and select the correct answer using the code given below the lists:

Solution:
QUESTION: 2

A rail which is tapered to a toe at one end and has a heel at the other end in called as:

Solution:
QUESTION: 3

For a chord of 60 m, the mid-ordinate for a circular curve of 50 m radius will be

Solution:
QUESTION: 4

The true length of a line is known to be 200 m. when this is measured with a 20 m tape, the length is 200.80 m. The correct length of the 20 m tape is

Solution:

Correct length of tape = 200 / 200.80 * 20 = 19.92 m

QUESTION: 5

Consider the following assumptions of Bowditch method:
1. Angular measurements are more precise than linear measurements.
2. Linear measurements are more precise than angular measurements.
3. Errors in linear measurements are proportional to√ L .
4. Correction to latitude or departure of any side
= Total error in L (or D)

Solution:
QUESTION: 6

The arithmetical check for the computation of R.L. by "rise and fall" method is given by

Solution:
QUESTION: 7

Match List-I with List-II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 8

Match List-I with List-II and select the correct answer using the codes:

Solution:
QUESTION: 9

Which one of the following pairs is not correctly matched ?

Solution:
QUESTION: 10

The dry density of a soil is 1.5 g/cc. If the saturation water content were 50% then its saturated density and submerged density would, respectively, be

Solution:

QUESTION: 11

If s is the shear strength , c and f are shear strength parameters, and sn is the normal stress at failure , then Coulonb's equation for shear strength of the soil can be represented by

Solution:
QUESTION: 12

Earth pressure and resultant possibilities of wall movement are shown in the below diagram. The point market X in the diagram denotes

Solution:
QUESTION: 13

Given that for a soil deposit,

K0 = earth pressure coefficient at rest,

Ka = active earth pressure coefficient

Kp= passive earth pressure coefficient and m -Poisson's ratio, the value of (1 – m)/m is given by

Solution:
QUESTION: 14

If D is the duration, ES and EF are the earliest start and finish, LS and LF are latest start and latest finish time, then the following relation holds good

Solution:
QUESTION: 15

Match List-I (Property)with List-II (Slope of the curve) and select the correct answer using
the code given below the lists:

Solution:
QUESTION: 16

A part of the Newmark's influence chart with four concentric circles is shown in the belowfigure. If the hateched areas 1 and 2 are loaded separately with the same intensity of loading, then the intensity of pressure yielded.

Solution:
QUESTION: 17

How many types of dressings are there with respect to the place of work?

Solution:

There are two types of dressings based on the place of work. They are quarry dressing and site dressing. Quarry dressing is carried out right after quarrying whereas site dressing is done after transporting the quarried rock to the site.

QUESTION: 18

Match List-I with List-II and select the correct answer using the code given below the lists:

Solution:
QUESTION: 19

Match List-I (Soils) with List-II (Group symbols) and select the correct answer using the
code given below the lists:

Solution:
QUESTION: 20

In the case of isolated square concrete footing, match the locations at which the stress resultants are to be checked, where d is effective depth of footing and select the correct answer using the codes given below the list :  Stress Resultant LocationA. Bending moment  1. At face of column B. One way shear 2. At d⁄ 2 from face of column C. Punching shear 3 At d from face of column?

Solution:
QUESTION: 21

A river is the source of water for water supply to a town. Its water is very turbid and polluted. The correct sequence of steps for freating the river water would be for treating the river water would be

Solution:
  • Coagulation and Flocculation

    Coagulation and flocculation are often the first steps in water treatment. Chemicals with a positive charge are added to the water. The positive charge of these chemicals neutralizes the negative charge of dirt and other dissolved particles in the water. When this occurs, the particles bind with the chemicals and form larger particles, called floc.

  • Sedimentation

    During sedimentation, floc settles to the bottom of the water supply, due to its weight. This settling process is called sedimentation.

  • Filtration

    Once the floc has settled to the bottom of the water supply, the clear water on top will pass through filters of varying compositions (sand, gravel, and charcoal) and pore sizes, in order to remove dissolved particles, such as dust, parasites, bacteria, viruses, and chemicals.

  • Disinfection

    After the water has been filtered, a disinfectant (for example, chlorine, chloramine) may be added in order to kill any remaining parasites, bacteria, and viruses, and to protect the water from germs when it is piped to homes and businesses.

  •  

QUESTION: 22

Uniformity coefficient of filter sand is given by

Solution:
QUESTION: 23

Match List-I with List II ans select the correct answer using the codes given below the lists:

Solution:
QUESTION: 24

Which one of the following would help prevent the escape of foul sewer gases from a water closet ?

Solution:
QUESTION: 25

Consider the following statements:

The daily per capital consumption of water apparently increases with

1. Higher standard of living of people

2. availability of sewerage in the city

3. metered water supply

4. wholesome and potable quality of water.

Which of these statement are correct?

Solution:
QUESTION: 26

Which one of the following sewage treatement units has a parshall flume ?

Solution:
QUESTION: 27

For fish habitat in a river, the minimum dissolved oxygen required is

Solution:
QUESTION: 28

Wrought iron contains carbon upto

Solution:
QUESTION: 29

Aerobic method of composting practised in India is called

Solution:
QUESTION: 30

Which one of the following filters will produce water of higher bacteriological quality?

Solution:
QUESTION: 31

Match List–I (Control structures) with List II (Functions of the Control structures) and select
the correct answer suing the codes given below the lists:

Solution:
QUESTION: 32

For medium silt whose average grain size is 0.16 mm, Lacey's silt factor is likely to be

Solution:
QUESTION: 33

The total number of independent equations that form Lacey's regime theory is

Solution:
QUESTION: 34

Consider the following:

Garret's diagram for the design of irrigationchannel is based on

1. Kennedy's theory

2. lacey's theory

3. Kutter's formula

4. Manning's formula

Which of these are correct ?

Solution:
QUESTION: 35

Water present in an artesian aquifer is usually

Solution:
QUESTION: 36

Match List–I (Name of scientist) with List II (Contribution of field of hydrology) and select
the correct answer suing the codes given below the lists:

 

Solution:
QUESTION: 37

In a linear reservior , the

Solution:
QUESTION: 38

Match List–I with List II and select the correct answer suing the codes given below the lists:

Solution:
QUESTION: 39

Match List–I with List II and select the correct answer suing the codes given below the lists:

Solution:
QUESTION: 40

In the time-cost analysis, the cost slope is defined as

Solution:
QUESTION: 41

Pay-back period gives an estimate of

Solution:
QUESTION: 42

Give that

d = effective depth

b = width and

D = overall depth

the maximum area of compression reinforcementin a beam is

Solution:
QUESTION: 43

The final deflection due to all loads including the effects of temperature, creep and shrinkage and measured from as cast level of supports of floors, roofs and all other horizontal members should NOT exceed

Solution:
QUESTION: 44

A reinfirced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is

Solution:

As per IS:456–2000, Cl. 26.5.2.2, the diameter of reinforcing bars shall not exceed one-eight of the total thickness of the slab. Hence, maximum diameter for slab thickness of 75 mm should be 8 mm.

 

 

QUESTION: 45

Drops are provided in flats slabs to resist

Solution:
QUESTION: 46

Consider the following statements:

Lug angles are used to

(1) increase the length of the end connectionsangle section

(2) decrease the length of end connections ofangle section

(3) increase the lengths of the end connectionsof channel section

(4) decrease the lengths of end connections ofchannel section

Which of the statements given above are correct?

Solution:
QUESTION: 47

As per IS : 456-1978, the ratio of stress in concrete to its characteristic strength at collapse in flexure for design purposes is taken as

Solution:

The compressive strength of concrete in the structure shall be assumed to be 0.67 times the characteristics strength. The partial safety factor of 1.5 shall be applied in addition to this Thus stress in concrete at collapse 

QUESTION: 48

Lateral ties in RC columns are provided to resist?

Solution:
QUESTION: 49

A bolt is subjected to a shear stress of  and a tensile stress of . If the permissible stresses in shear and tension are  and  respectively then the stress should satisfy:

Solution:

As per IS code no. 800:2007 for design of steel structure as per provision no. 

11.6.2.5 If the bolt is subjected to combined shear and 
tension, the actual shear and axial stresses calculated 
then the 
expression given below should satisfy: 

where 

&

= actual shear and tensile stresses 
respectively, and 

&

= permissible ‘hear and tensile ‘tresses respectively.

QUESTION: 50

Partial safety factor for concrete and steel are 1.5 and 1.15 respectively, because

Solution:
QUESTION: 51

As compared to working stress method of design, limit state method takes concrete to

Solution:
QUESTION: 52

Upper yield point in the stress-strain curve in structural steel can be avoided by

Solution:
QUESTION: 53

The effective length of the fillet weld is

Solution:
QUESTION: 54

Match List-I with List-II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 55

The economic spacing of a roof truss depends upon the

Solution:
QUESTION: 56

Consider the following statements :

Bearing stiffeners are provided in a plate girder

1. to avoid local bending failure of flange.

2. to prevent buckling of web.

3. to strengthen the web.

4. under uniformly distributed loads.

Which of these statements are correct ?

Solution:
QUESTION: 57

Match List-I (Propoerties) with List-II (Stress points labelled 1, 12, 3 and 4) and select the
correct answer using the codes given below the lists:

Solution:
QUESTION: 58

Which one of the following is the mode of failure in a fillet weld material?

Solution:
QUESTION: 59

The maximum permissible slenderness ratio of a member carrying loads resulting from wind, is

Solution:
QUESTION: 60

Match List-I (Failure Mode) with List-II (Reason) and select the correct answer using the
codes given below the lists:

Solution:
QUESTION: 61

The working stress for structural steel in tension is of the order of

Solution:
QUESTION: 62

Which one of the following is the chronological sequence is regard to road construction/developement ?

Solution:
QUESTION: 63

Which of the criteria given below are used for the design of valley vertical curves on roads ?

1. Rider comfort.

2. Headlight sight distance.

3. Drainage

Selected the correct answer using the codes given below:

Solution:
QUESTION: 64

Which one of the following pairs is NOT correctly matched ?

Solution:
QUESTION: 65

In cement concrete pavements, tie bars are installed in

Solution:
QUESTION: 66

For carrying out bituminous patch work during the rainy season, the most suitable binder is

Solution:
QUESTION: 67

Match List-I with List-II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 68

The modulus of elasticity of timber is about

Solution:
QUESTION: 69

Which of the following pairs in respect of ordinary portland cement (OPC) are correctly matched ?

1. Initial setting time .......... 30 minutes

2. Final setting time ........ 10 hours

3. Normal consistency..... 10%

Select the correct answer using the codes givenbelow : Codes :

Solution:
QUESTION: 70

High alumina cement is produced by fusing together a mixture of

Solution:
QUESTION: 71

Which one of the following types of steels is used in the manufacture of rails?

Solution:
QUESTION: 72

Linseed oil is used in paints as

Solution:
QUESTION: 73

Before testing setting time of cement one should test for

Solution:
QUESTION: 74

The tempeture range in a cement kiln is

Solution:
QUESTION: 75

Match List–I (Admistures) with List II (Chemicals) and select the correct answer suing
the codes given below the lists:

Solution:
QUESTION: 76

The deformation of a bar under its own weight as compared to that when subjected to a direct axial load equal to its own weight will be

Solution:
QUESTION: 77

A solid uniform metal bar of diameter D and length L is hanging vertically from its upper end.The elongation of the bar due to self weight is

Solution:
QUESTION: 78

If Poisson's ratio of a material is 0.5, then the elastic modulus for the material is

Solution:
QUESTION: 79

The volumetric strain in case of a thin cylindrical shell of diameter 'd', thickness 't', subjected to internal pressure 'P' is

Solution:
QUESTION: 80

Match List – I (State of stress) with List -II (kind of loading) and select the correct answer using the codes given below the lists:

 

Solution:
QUESTION: 81

In a strained material, normal stresses on two mutually perpendicular planes are σx and σy (both alike) accompanied by a shear stress τxy. One of the principal stresses will be zero, only it

Solution:

QUESTION: 82

Auto frettage is the method of

Solution:
QUESTION: 83

In a thick cylinder pressurized from inside, the hoop stress is maximum at

Solution:
QUESTION: 84

A simply supported beam is loaded as shown is the figure below.

The maximum shear force in the beam will be

Solution:
QUESTION: 85

In a beam of circular cross-section, the shear stress variation across a cross section is

Solution:
QUESTION: 86

The distribution of shear stress of a beam is shown in the given figure.

Solution:
QUESTION: 87

A shaft is subjected to torsion as shown in the figure below.

Which of the following figures represents the shear stress on the element LMNOPQRS?

Solution:
QUESTION: 88

A beam subjected to a load P is shown in the figure below.

The bending moment at the supports A of thebeam will be

Solution:
QUESTION: 89

Match List-I (Rheological equation) with List- II (Types of fluids) and select the correct answer
using the codes given below the lists:

Solution:
QUESTION: 90

An oil of specific gravity 0.9 has viscosity of 0.28 stokes at 38ºC. What will be its viscosity in Ns/ m2?

Solution:
QUESTION: 91

The depth of fluid is measured in vertical zdirection; xand y are the other two directions and are mutually perpendicular. The static pressure variation in the fluid is given by (symbols have the usual meaning)

Solution:
QUESTION: 92

A 70 kg person walds on snow with a total foot implint area of 500 cm2. What pressure does he exert on show?

Solution:
QUESTION: 93

Manometer is a device used for measuring

Solution:
QUESTION: 94

A rectangular water tank, full to the brim, has its length, breadth and height in the ratio of 2: 1 : 2. The ratio of hydrostatic forces at the bottom to that at any larger vertical surface is

Solution:
QUESTION: 95

Three immiscible liquids of specific densities r, 2r and 3r are kept in a jar. The height of theliquied in the jar and at the piezometer fitted to the bottom of the jar are as shown in the figure below.

The ratio H/h is .

Solution:

QUESTION: 96

The prssure centre is

Solution:
QUESTION: 97

The Euler's equation of motion is a statement of

Solution:
QUESTION: 98

When is Bernoulli's equation applicable between any two points in a flow field?

Solution:
QUESTION: 99

For an irrotational motion

Solution:
QUESTION: 100

How are the velocity coefficient Cv, the discharge coefficient Cd, and the contraction coefficient Cc of an orifice related?

Solution:

Coefficient of discharge (Cd) = Coeff. of flow/velocity (Cv) x Coeff of contraction (Cc).

where

Cd = actual discharge/theoretical discharge

Cc = Area of vena contracta/ area of orifice

Cv = actual velocity at vena contracta/theoretical velocity