Test: Civil Engineering (SSC JE) Technical- 4


100 Questions MCQ Test Mock test series of SSC JE Civil Engineering | Test: Civil Engineering (SSC JE) Technical- 4


Description
This mock test of Test: Civil Engineering (SSC JE) Technical- 4 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam. This contains 100 Multiple Choice Questions for Civil Engineering (CE) Test: Civil Engineering (SSC JE) Technical- 4 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Civil Engineering (SSC JE) Technical- 4 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE) students definitely take this Test: Civil Engineering (SSC JE) Technical- 4 exercise for a better result in the exam. You can find other Test: Civil Engineering (SSC JE) Technical- 4 extra questions, long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.
QUESTION: 1

If the degree of saturated of a partially saturated soil is 60% then air content of the soil is

Solution:
QUESTION: 2

In hydrometer analysis for a soil mass

Solution:
QUESTION: 3

The hydrometer method of sedimentation analysis differs from the pipette analysis mainly in

Solution:
QUESTION: 4

Rise of water table above the ground surface causes

Solution:
QUESTION: 5

In a beam and slab structure, if width of beam is bw, depth of slab Df, lo is the distance between points of zero moments in the beam, effective width of intermediate flange is given by

Solution:
QUESTION: 6

Physical properties which influence permeability are

Solution:
QUESTION: 7

Phreatic line in an earthen dam is

Solution:
QUESTION: 8

Time factor for a clay layer is

Solution:
QUESTION: 9

Passive earth pressure in a soil mass is proportional to

Solution:
QUESTION: 10

A soil having particles of nearly the same size isknown as:

Solution:
QUESTION: 11

Which of the following have an influence on the value of permeability?
1. void ratio
2. degree of saturation
3. pressure head
4. grain size

Select the correct answer using the codes given below:

Solution:
QUESTION: 12

Match List I with List II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 13

Given that , the depth of tension crack developing in a cohesivesoil backfill would be

Solution:
QUESTION: 14

The main principle of surveying is to work

Solution:
QUESTION: 15

Vertical component of shear resisted by stirrups inclined at α to vertical in a R.C. beam is

Solution:
QUESTION: 16

The correction to be applied to each 30 metre chain length along θ slope , is

Solution:
QUESTION: 17

The line normal to the plumb line is known as

Solution:
QUESTION: 18

In levelling operation

Solution:
QUESTION: 19

The staff intercept will be

Solution:
QUESTION: 20

If i is the stadia distance, f is the focal length andd is the distance between the objective andvertical axis of the techeometer, the multiplying constant is

Solution:
QUESTION: 21

Planimeter is used for measuring

Solution:
QUESTION: 22

Match List-I with List-II and choose a correct answer by using the codes given below the lists:

Solution:
QUESTION: 23

A point determined by resection on a plane tableis called:

Solution:
QUESTION: 24

Nagpur road plan fomulae watch prepared byassuming

Solution:
QUESTION: 25

The shape of the camber, best suited for cementconcrete pavements, is

Solution:
QUESTION: 26

Desire lines are plotted in

Solution:
QUESTION: 27

The maximum width of a vehicle asrecommended by IRC is

Solution:
QUESTION: 28

For highway geometric design purposes thespeed used is

Solution:
QUESTION: 29

Traffic volume is equal to

Solution:
QUESTION: 30

Maximum number of vehicles can be parked with

Solution:
QUESTION: 31

Bitumen of grade 80/100 means

Solution:

Correct Answer :- c

Explanation : Bitumen of grade 80/100 means its penetration value is 8 to 10 mm.

QUESTION: 32

Flexible pavement distribute the wheel load

Solution:
QUESTION: 33

Match List-I with List-II and choose a correct answer by using the codes given below the lists:

Solution:
QUESTION: 34

Rapid curing cut back bitumen is produced by blending bitumen with

Solution:
QUESTION: 35

The rail is designated by its

Solution:
QUESTION: 36

The standard length of rail for Broad Gauge andMetre Gauge are respectively

Solution:
QUESTION: 37

The side slope of embankments for a railwaytrack is generally taken as

Solution:
QUESTION: 38

Creep is the

Solution:
QUESTION: 39

an isochrone is line on the basin map

Solution:
QUESTION: 40

An accurate estimate of average rainfall in aparticular catchment area can be obtained by

Solution:
QUESTION: 41

Which one of the following defines Aridity index (AI) ?

Solution:
QUESTION: 42

The discharge per unit drawdown at the well isknown as

Solution:
QUESTION: 43

What is 'Hydrological Cycle' ?

Solution:
QUESTION: 44

The double mass curve technique is used:

Solution:
QUESTION: 45

Match List–I with List–II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 46

Consider the following chemical emulsions:
1. Methyl alcohol
2. Cetyl alcohol
3. Stearyl alcohol
4. Kerosene
Which of the above chemical emulsions is/are used to minimize the loss of water through the
process of evaporation?

Solution:
QUESTION: 47

Match List-I (Name of scientists) with List-II (Contribution to field of hydrology) and select
the correct answer using the codes given below the lists:

Solution:
QUESTION: 48

In the design of isolated column footing, ofthickness d the critical section from theconsideration of single shear is

Solution:
QUESTION: 49

Ombrometer (pluviometer) is used to measure

Solution:
QUESTION: 50

As per IS : 800, the maximum deflection in a beam should not exceed

Solution:
QUESTION: 51

Bending compressive and tensile stressesrespectively are calculated based on

Solution:
QUESTION: 52

If the thickness of thinnest outside plate is 10mm, then the maximum pitch of rivets in tensionwill be taken as

Solution:
QUESTION: 53

As per IS : 800, the thickness of slab base is given by

Solution:
QUESTION: 54

Which of the following types of riveted joint isfree from bending stresses?

Solution:
QUESTION: 55

As compared to field rivets, the shop rivets are

Solution:
QUESTION: 56

In the cross-section of a weld, throat is the

Solution:
QUESTION: 57

Rocks formed due to alteration of originalstructure due to heat and excessive pressure,arecalled

Solution:
QUESTION: 58

If P is the percentage of water required fornormal consistency, water to be added fordetermination of initial setting time, is

Solution:
QUESTION: 59

Minimum required watwer cement ratio for aworkable concrete, is

Solution:
QUESTION: 60

Most commonly used solvent in oil paints, is

Solution:
QUESTION: 61

Turpentine oil is used in paints as

Solution:
QUESTION: 62

The commonly used thinner in oil paints, is

Solution:
QUESTION: 63

Oil varnish generally consists of

Solution:
QUESTION: 64

Match List-I with List-II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 65

IS code recommends that the slope of stairsshould be between

Solution:
QUESTION: 66

Quick lime (or caustic lime)

Solution:
QUESTION: 67

Pick up the compound responsible for earlystrength of cement from the following

Solution:
QUESTION: 68

If water required for 1 bag of cement is 30 litres,the water cement ratio is :

Solution:
QUESTION: 69

Match List-I with List-II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 70

Pick up the timber from the following which isused for railway sleepers:

Solution:
QUESTION: 71

Which eccentric load, if placed within the central core shown in figures below, does not produce
tension in the column cross-section?

Solution:
QUESTION: 72

Limiting value of depth of neutral axis in R.C.beam od depth d with Fe 415 steel is

Solution:
QUESTION: 73

For the above cantilever beam, the absolute value of shear force at A is

Solution:
QUESTION: 74

IS 456 – 2000 recommends that in any columnreinforcement shal not be more than

Solution:
QUESTION: 75

0.2 per cent proof stress means

Solution:
QUESTION: 76

Endurance limit is

Solution:
QUESTION: 77

A strain gauge consists of a group of _______rosetts.

Solution:
QUESTION: 78

Match List I with List II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 79

Water obtained from _____ is generally knownas sub-surface water.

Solution:
QUESTION: 80

Which of the following is used for computing thequantity of water for fire demand?

Solution:
QUESTION: 81

Spacing of longitudinal bars measured along theperiphery of R.C. column shall not exceed

Solution:
QUESTION: 82

Aeration is carried out to

Solution:
QUESTION: 83

Floatation is a method of water purification by

Solution:
QUESTION: 84

In fill and draw type of sedimentation tanks thetime required for one cycle is

Solution:
QUESTION: 85

The most common and universal coagulant usedin water works is

Solution:
QUESTION: 86

What indicates the permanent hardness when alum is added to water?

Solution:

The presence of calcium sulfate indicates the permanent hardness in water when alum is added to water.

QUESTION: 87

Which one of the following is not a method ofdesalination ?

Solution:
QUESTION: 88

Which one of the following layout of waterdistribution system is known as interlacedsystem?

Solution:
QUESTION: 89

If P is the axial load and Pu is the factored axial load on the footing, area of footing required is

Solution:
QUESTION: 90

Sewer lines are designed for a design period of

Solution:
QUESTION: 91

An egg-shaped section of sewer

Solution:
QUESTION: 92

Manholes are generally located at

Solution:
QUESTION: 93

Match List-I (Equipment) with List-II (Parameter) and select the correct answer using
the codes given below the lists:

Solution:
QUESTION: 94

Figure shows a typical interaction curve for column design. Match List-I with List-II

Solution:
QUESTION: 95

The most suitable solid waste disposal methodfor rural areas is

Solution:
QUESTION: 96

Match List–I with List–II and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 97

Which one of the following pairs is not correctly matched?

Solution:
QUESTION: 98

Match List–I with List–II and select the correct answer using the codes given below the lists:
List–I
a. Vertical Cliff
b. Steep slope
c. Hill
d. Overhanging cliff
 

LIST – II
1. Contour lines of different elevations unite to form one line
2. Contour lines of different elevations cross one another
3. Contour lines are closely spaced
4. Closed contour lines with higher values inside them

 

Solution:
QUESTION: 99

Match List–I (Terms) with List–II (Description) and select the correct answer using the codes
given below the lists:
 

List–I
a. Contour
b. Line of collimation
c. Tie line
d. Magnetic meridian
 

LIST – II
1. Line joining magnetic North and South
2. Line joining subsidiary station on the main line
3. Line joining points of same elevation
4. Line joining optical centre of the objective lens with point of intersection of cross-wires

Solution:
QUESTION: 100

Cavitation takes place if the pressure of the fluidflowing at any point is

Solution: