Test: Civil Engineering (SSC JE) Technical- 5


100 Questions MCQ Test Mock test series of SSC JE Civil Engineering | Test: Civil Engineering (SSC JE) Technical- 5


Description
This mock test of Test: Civil Engineering (SSC JE) Technical- 5 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam. This contains 100 Multiple Choice Questions for Civil Engineering (CE) Test: Civil Engineering (SSC JE) Technical- 5 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Civil Engineering (SSC JE) Technical- 5 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE) students definitely take this Test: Civil Engineering (SSC JE) Technical- 5 exercise for a better result in the exam. You can find other Test: Civil Engineering (SSC JE) Technical- 5 extra questions, long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.
QUESTION: 1

Upper yield point in the stress strain curve instructural steel can be avoided by

Solution:
QUESTION: 2

The effective length of a structural steelcompression member of length L effectively heldin position and restrained against rotation at oneend but neither held in position and restrainedagainst rotation at the other end, is

Solution:
QUESTION: 3

Consider the following statements:A grillage base is checked for
 

1. bending
2. shear
3. compression
4. web crippling

Which of these statements are correct

Solution:
QUESTION: 4

The permissible stresses for main structural steelmembers under dynamic loads should beincreased by

Solution:
QUESTION: 5

As per IS : 800 in the case of a plate girder withvertical and horizontal stiffeners, the greater andlesser unsupported clear dimension of a webthickness 'tw' should not exceed respectively

Solution:
QUESTION: 6

Which one of the following is the load factor?

Solution:
QUESTION: 7

Which one of the following pairs is correctlymatched ?

Solution:
QUESTION: 8

In a plate grinder bridge the thickness of web isless than d '/200 where d ' is the unsupporteddepth of web. The web plate should be providedwith

Solution:
QUESTION: 9

What is the maximum slenderness ratio of lacingbars in built-up columns?

Solution:
QUESTION: 10

Where should splices in the columns be provided?

Solution:
QUESTION: 11

Geologically, marble is known as

Solution:
QUESTION: 12

Geologically, marble is known as

Solution:
QUESTION: 13

Index number expressing the relative seizes ofboth coarse and fine aggregates, is called

Solution:
QUESTION: 14

The most durable varnish is

Solution:
QUESTION: 15

Lacquer is

Solution:
QUESTION: 16

Bitumen in

Solution:
QUESTION: 17

According to ISI, bitumen is classified into

Solution:
QUESTION: 18

Smith's test of stones is performed to find out

Solution:
QUESTION: 19

Match the List-I with List-II and select a suitable
answer by using the codes given below the lists

 

 

Solution:
QUESTION: 20

The foundation in which a cantilever beam isprovided to join two footings, is known as

Solution:
QUESTION: 21

Black cotton soil is unsuitable for foundationsbecause its

Solution:
QUESTION: 22

On a diagonal scale, it is possible to read up to

Solution:
QUESTION: 23

Diaphragm of a surveying telescope is held inside

Solution:
QUESTION: 24

Contour interval, within the limits of a map

Solution:
QUESTION: 25

Closed contours of decreasing values towards their centre, represent

Solution:
QUESTION: 26

The theodolites used for making tacheometricobservations by optical wedge system, are

Solution:
QUESTION: 27

The radius of a simple circular curve is 300 mand length of its specified chord is 30 m. Thedegree of the curve is

Solution:
QUESTION: 28

With usual notations, the expression  represents

Solution:
QUESTION: 29

Cross-staff is used for

Solution:
QUESTION: 30

In case of reduction of levels by the height of
instrument method

Solution:
QUESTION: 31

The ratio of long chord and length of a curve of radius R deflecting through Δ º, is

Solution:
QUESTION: 32

Which one of the following procedures for getting accurate orientation is the most distinctive featureof the art of plane tabling

Solution:
QUESTION: 33

The inventor of the term soil mechanics, was

Solution:
QUESTION: 34

. Geologic cycle for the formation of soil, is

Solution:
QUESTION: 35

Chemical weathering of soil is caused due to

Solution:
QUESTION: 36

Water content of a soil sample is the differenceof the weight of the given sample at the giventemperature and the weight determined afterdrying it for 24 hours at temperature ranging from

Solution:
QUESTION: 37

The specific gravity of sands is approximately

Solution:
QUESTION: 38

If W1, W2, W3 and W4 are the sequential weights obtained during observations in pycnometer
method for determining water content, the formula to be used, is

Solution:
QUESTION: 39

The property of a soil which allows it to bedeformed rapidly without rupture, elastic reboundand also a volume change, is known

Solution:
QUESTION: 40

Darcy's law is applicable to seepage if a soil is

Solution:
QUESTION: 41

The coefficient ka of the active earth pressure, is given by

Solution:
QUESTION: 42

Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H andacts at

Solution:
QUESTION: 43

A soil not fully consolidated under the existing over-burden pressure, is called

Solution:
QUESTION: 44

A sample of saturated soil has 30% water content and the specific gravity of soil grains is 2.6. Thedry density of the soil mass in g/cm3, is

Solution:
QUESTION: 45

The water content in a soil sample when it continues to loose weight without loosing thevolume, is called

Solution:
QUESTION: 46

Match List I with List II and select the correct answer using codes given under the lists:

Solution:
QUESTION: 47

 If the specific gravity of solids is 2.5 and the watercontent of a saturated soil is 40%, then match
the List I with List II and choose a correct answer by using the codes given below the lists:

Solution:
QUESTION: 48

The strength and quality of concrete, depend upon :

Solution:
QUESTION: 49

Separation of coarse aggregates from mortarduring transportation, is known

Solution:
QUESTION: 50

Separation of water or water sand cement froma freshly concrete, is known

Solution:
QUESTION: 51

Efflorescence in cement is caused due to anexcess of

Solution:
QUESTION: 52

Water cement ratio is

Solution:
QUESTION: 53

Match List I with List II and select the correct answer using codes given below the lists:

List-I
A. Aggregate Texture
B. Aggregate crushing value
C. Aggregate impact value
D. Aggregate abrasion value
List-II
1. The resistance of the material to failure by
impact.
2. The relative degree to which particle surface
is smooth
3. The relative resistance to wear
4. Relative measure of the resistance of an
aggregate sample to crushing gradually
applied crushing load.

Solution:
QUESTION: 54

As the percentage of steel increases

Solution:
QUESTION: 55

By over-reinforcing a beam, the moment ofresistance can be increased not more than

Solution:
QUESTION: 56

The neutral axis of a T-beam exists

Solution:
QUESTION: 57

A T-beam behaves as a rectangular beam of awidth equal to its flange if its neutral axis

Solution:
QUESTION: 58

The diameter of transverse reinforcement ofcolumns should be equal to one-fourth of thediameter of the main steel rods but not less than

Solution:
QUESTION: 59

The spacing of transverse reinforcement ofcolumn is decided by the following consideration

Solution:
QUESTION: 60

Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel
to lx and ly be wx and wy respectively. According to Rankine Crashoff theory

Solution:
QUESTION: 61

The amount of reinforcement for main bars in aslab, is based upon

Solution:
QUESTION: 62

The ratio of the limiting value of the depth of neutral axis and the depth of the section of a singly
reinforced beam is equal to :

where .σ y is the characteristic strength and Es is the modulus of elasticity of steel

Solution:
QUESTION: 63

Indian Road Congress (I.R.C.) was founded and constituted with its head quarters at New Delhi,in

Solution:
QUESTION: 64

In water bound macadam roads, binding material, is

Solution:
QUESTION: 65

In scanty rainfall regions, the camber provided will be

Solution:
QUESTION: 66

Camber in pavements is provided by

Solution:
QUESTION: 67

An exceptional grade may be provided upto 1in 12 along hill roads, if the length does not exceed

Solution:
QUESTION: 68

Raising of outer edge of a road with respect to inner edge, is known

Solution:
QUESTION: 69

The ability of a driver to stop the vehicle moving with the designed speed, depends upon :

Solution:
QUESTION: 70

The ideal shape of a transition curve, is

Solution:
QUESTION: 71

Match List I with List II and select the correct answer using codes given below the lists:

List-I
A. Roman Roads
B. Tresaguet Roads
C. Metcalf-Roads
D. Telford Roads
 

List-II
1. As per Robert Phillips specifications
2. Foundation stones of sizes 17 to 22 cm
3. Cross-slope of 1 in 45 to the surfaceUpdate Question
4. Top surface is provided with large stone
slabs in lime 10 to 15 cm thick

Solution:
QUESTION: 72

Match List I with List II and select the correct answer using codes given below the list:

List-I (Type of road)
A. Single lane road
B. Two lanes road without Kerbs
C. Two lanes with raised Kearbs
D. Multi-lane pavements
List-II (Width of carriage way)
1. 7.0m
2. 7.5m
3. 3.75m
4. 3.5 m per lane

Solution:
QUESTION: 73

Match List I with List II and select the correct answer using codes given below the lists:

Solution:
QUESTION: 74

Match List I with List II and select the correct answer using codes given below the lists:


 

Solution:
QUESTION: 75

In the phenomenon of cavitation, the characteristic fluid property involved is

Solution:
QUESTION: 76

What is the unit of dynamic viscosity of a fluid termed 'poise' equivalent to ?

Solution:
QUESTION: 77

If the intensity of irrigation for Kharif is 45% and that for Rabi is 60%; then the annual intensity ofirrigation, is :

Solution:
QUESTION: 78

If τCis the critical shear stress on a channel bed, then the critical shear on the side slopes (nH :
IV) of this channel ( τC ) is

Solution:

QUESTION: 79

The centre of pressure for an inclined surface area

Solution:
QUESTION: 80

With the increase in supplied irrigation water, the yield of crops:

Solution:
QUESTION: 81

The water which can be utilised by the crop sfrom the soil is called :

Solution:
QUESTION: 82

Permanent wilting point moisture content for a crop represents the

Solution:
QUESTION: 83

In an axial flow impulse turbine, energy transfer takes place due to

Solution:
QUESTION: 84

The Δ (in m) for a crop, having quantity duty D
(in ha/M. cum), and base period B (in days) is
given by

Solution:
QUESTION: 85

Which of the following hydraulic turbines are reaction turbines ?
1. Francis
2. Kaplan
3. Propeller

Solution:
QUESTION: 86

Slender bar of 100 mm2 cross-section is
subjected to loading as shown in the figure below.
If the modulus of elasticity is taken as 200 × 109
Pa, then the elongation produced in the bar will
be

Solution:
QUESTION: 87

The Poisson ratio of a material which has Young's modulus of 120 GPa and shear modulus of 50GPa, is

Solution:
QUESTION: 88

The volumetric strain in case of a thin cylindrical shell of diameter 'd', thickness 't', subjected tointernal pressure 'p' is

Solution:
QUESTION: 89

What is the relationship between elastic constants E, G and k ?

Solution:
QUESTION: 90

Normal stresses of equal magnitude  , but ofopposite signs, act at a point of a strained materialin perpendicular direction. What is the magnitudeof the stress on a plane inclined at 45º to theapplied stresses ?

Solution:
QUESTION: 91

For a general two dimensional stress system, what are the coordinates of the centre of Mohr's
circle?

Solution:
QUESTION: 92

The commonly used technique of strengthening thin pressure vessels is

Solution:
QUESTION: 93

The Garret's diagrams are based on :

Solution:
QUESTION: 94

A seamless pipe of diameter d m is to carry fluid under a pressure of p kN/cm2. The necessary
thickness t of metal in cm, if the maximum stress is not to exceed σ kN/cm2 is

Solution:
QUESTION: 95

The bending moment diagram shown in figure-I corresponds to the shear force diagram in

Solution:
QUESTION: 96

The ratio of torque carrying capacity of a solid shaft to that of a hollow shaft is given by

Solution:
QUESTION: 97

A structural member subjected to an axial compressive force is called

Solution:
QUESTION: 98

If a material expands freely due to heating, it will develop

Solution:
QUESTION: 99

A cantilever of length L, moment of inertia I,Young's modulus E carries a concentrated load W at the middle of its length. The slope ofcantilever at the free end is

Solution:
QUESTION: 100

In a body, thermal stress is induced because of the existence of

Solution: