Electronic communication refers to
Explanation:When information are sent from one point to the other it has to be converted into electrical signal using transducer.The receiver receives it in its original from using receiver.Such from of communication is called electronic communication.
FM Radio set used in cars is
Explanation: Radio means sending energy with waves. In other words, it's a method of transmitting electrical energy from one place to another without using any kind of direct, wired connection. That's why it's often called wireless. The equipment that sends out a radio wave is known as a transmitter; the radio wave sent by a transmitter whizzes through the air—maybe from one side of the world to the other—and completes its journey when it reaches a second piece of equipment called a receiver((here a radio).
For a signal to be reproduced without distortion
Most vibrating objects have more than one resonant frequency and those used in musical instruments typically vibrate at harmonics of the fundamental. A harmonic is defined as an integer (whole number) multiple of the fundamental frequency.
A woofer should be fed from the input through a
Woofer is a low frequency loud speaker covering the range 16 Hz to 500 Hz.
AM detection is
The three elements of a generalized communication system are
Explanation:In communication the Transmitter helps in transmitting the signal through communication channel which acts as a physical path that connects transmitter to a receiver.And the receiver receives the transmitted signal and converts those signals in their original form.
TV set used in a typical house is
Explanation: The equipment that sends out a radio wave is known as a transmitter; the radio wave sent by a transmitter whizzes through the air—maybe from one side of the world to the other—and completes its journey when it reaches a second piece of equipment called a receiver.A television antenna, or TV aerial, is an antenna specifically designed for the reception of over-the-air broadcast television seignal, which are transmitted at frequencies from about 41 to 250 MHz in the VHF band, and 470 to 960 MHz in the UHF band in different countries..
Audio signals have a maximum bandwidth of about
Pulse is specified by pulse height or the peak voltage, the pulse duration and pulse to pulse spacing. In pulse amplitude modulation (PAM) what changes with base band signal is
A rectifier and an envelope detector for AM uses
Electronic communication is not possible if
Explanation:As the information or message is transmitted from the source to the receiver ,it is first converted into electrical signal which is then transmiited through the communication medium.Hence in electrical communication it is must to convert raw message or information into electrical signal.Else the electronic messages will not be transmitted.
For attenuation of high frequencies we should use
Since Xc for high frequencies is low, the high frequencies are shunted to ground and are not transmitted.
Coaxial cables have a bandwidth in the range of
To reduce the distortion in amplitude modulation, modulation index is kept
Frequencies in the UHF range normally propagate by means of:
Which of these is an example of point to point communication?
Explanation:In point to point communication,communication occurs over a link between a single transmitter and receiver.Telephony is an example of it as it needs a link between caller and receiver to transmit the information.This link is provided by various media like cable.
Amplification is the
Explanation:It is the process of increasing the amplitude and hence the strength of an elctrical signal by using an electric circuit having atleat on transistor is called amplifier.Amplification is rerquired to compensate for the loss of strenght of a signal during its transmission.The additional energy is otianed from a dc source.The process of amplification is done at a location betwen the sources and the destination where the strength of signal becomes weaker than the required level.
Transmission bandwidth of fiber optic communication can be up to
One method of producing an amplitude modulation is to add the carrier and modulating signal and then
A carrier wave of peak voltage 12V is used to transmit a message signal. What should be the peak voltage of the modulating signal in order to have a modulation index of 75%?
Which of these is an example of broadcast communication?
Explanation:In broadcast mode of communication a large number of receivers are linked to a single transmiiter.Radio works as receiver which converts the transmiited information/message into the original form of the information.
Range of an electronic communication system
Explanation:As the distance between the source and the destination increases the strenght of the transmitted signals become weaker and weaker and the distance where it loses energy to travel any more is range of the signal.
In ground wave propagation the earth
Before transmission the AM produced by a square law device
Multiplexing is a scheme for transmitting multiple signals at the same time e.g. speeches of ten persons in different rooms on the same channel. How many transmitters will be required in any multiplexing scheme?
Transducer is a device that
Explanation:Any device which converts energy from one form to another is called a transducer.It converts variation in physical quantities such as pressure,dispalcement,force,temprature etc.Like microphone converts sound signal into an electrical signal.
Bandwidth of an electronic communication system
Explanation: A range within a band of wavelengths, frequencies, or energies; especially : a range of radio frequencies which is occupied by a modulated carrier wave, which is assigned to a service, or over which a device can operate.
Ground wave propagation is used for
The range of an AM broadcast depends
In Amplitude modulation if one of the two side bands is removed by a filter is it possible to recover the modulating signal?