Courses

# Design of Bearings - MCQ Test 1

## 20 Questions MCQ Test RRB JE for Mechanical Engineering | Design of Bearings - MCQ Test 1

Description
This mock test of Design of Bearings - MCQ Test 1 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam. This contains 20 Multiple Choice Questions for Mechanical Engineering Design of Bearings - MCQ Test 1 (mcq) to study with solutions a complete question bank. The solved questions answers in this Design of Bearings - MCQ Test 1 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering students definitely take this Design of Bearings - MCQ Test 1 exercise for a better result in the exam. You can find other Design of Bearings - MCQ Test 1 extra questions, long questions & short questions for Mechanical Engineering on EduRev as well by searching above.
QUESTION: 1

### Spherical roller bearings are normally used

Solution:

It is also true for (a) but (d) is more appropriate.

QUESTION: 2

Solution:

QUESTION: 3

### The basic load rating of a ball bearing is

Solution:
QUESTION: 4

To restore stable operating condition in a hydrodynamic journal bearing, when it encounters higher magnitude loads,

Solution:
QUESTION: 5

In thick film hydrodynamic journal bearings, the coefficient of friction

Solution:
QUESTION: 6

Consider the following statements about antifriction bearings:

1. Their location influences the lateral critical speed of a rotor.

2. Roller bearings are antifriction bearings. Which of the statements given above is/are correct?

Solution:
QUESTION: 7

In three ball bearing identified as

SKF 2015, 3115 and 4215

Solution:

According to ISO plan for dimension series bearings are provided with two digit numbers. The first number indicates the width series 8, 0, 1, 2, 3, 4, 5 and 6 in order of increasing width. The second number indicate diameter series 7, 8, 9, 0, 1, 2, 3, and 4 in order of ascending outer diameter of bearing. Thus bearing number SKF 2015, 3115 and 4215 shows bearings belonging to different series with 75 mm bore diameter but width is increasing. SKF 2015, 3115 and 4215 shows width is increasing ascending outer diameter of bearing same bore diameter 75 mm. (i.e. 15 × 5)

QUESTION: 8

The rating life of a group of apparently identical ball bearings is defined as the number of revolutions or exceeded before the first evidence of fatigue crack by:

Solution:
QUESTION: 9

The rolling element bearings are

Solution:
QUESTION: 10

On what does the basic static capacity of a ball bearing depends?

Solution:
QUESTION: 11

In a single row deep groove ball-bearing, cages are needed to

Solution:
QUESTION: 12

Assertion (A): It is desirable to increase the length of arc over which the oil film has to be maintained in a journal bearing.

Reason (R): The oil pressure becomes negative in the divergent part and the partial vacuum created will cause air to leak in from the ends of bearing.

Solution:
QUESTION: 13

Removal of metal particles from the raceway of a rolling contact bearing is a kind of failure of bearing known as

Solution:
QUESTION: 14

Assertion (A ): Tapered roller bearings are sensitive to the tightening between inner and outer races.

Reason (R): Tapered roller bearings are always provided with adjusting nut for tightening.

Solution:
QUESTION: 15

Match List-I (Bearings) with List-II (Applications) and select the correct answer using the codes given below the lists:

Solution:
QUESTION: 16

Tapered roller bearings can take

Solution:
QUESTION: 17

Which of the following are included in the finishing operations for porous bearing?

1. Infiltration  2. Sizing   3. Heat treatment  4.Coining

Select the correct answer using the code given below:

Solution:
QUESTION: 18

Which one of the following is correct?

A hydrodynamic slider bearing develops load bearing capacity mainly because of

Solution:

A hydrodynamic slider bearing develops load bearing capacity mainly because of wedge shaped oil film.

QUESTION: 19

A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary?

Solution:

When the load and speed is doubled, the minimum film thickness remains unchanged. Since,

Since S remains the same even after doubling the speed as well as load and film Thickness depends on the Sommerfeld number.

QUESTION: 20

What is the main advantage of hydrodynamic bearing over roller bearing?

Solution: