Courses

# Test: Forming Processes - 3

## 30 Questions MCQ Test Topicwise Question Bank for Mechanical Engineering | Test: Forming Processes - 3

Description
This mock test of Test: Forming Processes - 3 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam. This contains 30 Multiple Choice Questions for Mechanical Engineering Test: Forming Processes - 3 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Forming Processes - 3 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering students definitely take this Test: Forming Processes - 3 exercise for a better result in the exam. You can find other Test: Forming Processes - 3 extra questions, long questions & short questions for Mechanical Engineering on EduRev as well by searching above.
QUESTION: 1

Solution:
QUESTION: 2

Solution:
QUESTION: 3

### Tandem drawing of wires and tubes is necessary because

Solution:
QUESTION: 4

Match the List-l (Processes) with List-lI (Production of parts):
List-l
A. Rolling
B. Forging
C. Extrusion
D. Drawing
List-lI
1. Discrete parts
2. Rod and wire
3. Wide variety of shapes with thin walls
4. Flat plates and sheets
5. Solid and hollow parts
Codes:
A    B    C   D
(a)  2    5    3    4
(b)  1    2    5    4
(c)  4    1    3    2
(d)  4    1    5    2

Solution:
QUESTION: 5

The blank diameter used in thread rolling will be

Solution:

Thread rolling is a cold-forming process in which threads are formed on round rods by passing them between rotating dies.

QUESTION: 6

The reduction in sheet-metal drawing is defined as
where,
D = Blank diameter
d = Punch diameter

Solution:
QUESTION: 7

Ironing is used to

Solution:
QUESTION: 8

Solution:
QUESTION: 9

Match the List-I (Extrusion processes) with List-lI (Related description):
List-I
A. Direct extrusion
B. Indirect extrusion
C. Hydrostatic extrusion
D. Tube extrusion
List-Il
1. Mandrel
2. No friction
3. Stationary die
4. Moving die
Codes:
A B C D
(a) 4 2 3 1
(b) 3 2 4 1
(c) 3 4 2 1
(d) 3 4 1 2

Solution:
QUESTION: 10

Swaging is an operation of

Solution:

In swaging a solid rod or tube is subjected to radial impact forces by a set of reciprocating dies. The die movements can be obtained by means of a set of rollers in a cage, is an action similar to that of a roller bearing.

QUESTION: 11

Which one of the following is an advantage of forging

Solution:
QUESTION: 12

Solution:
QUESTION: 13

In the forging operation, fullering is done to

Solution:

Fullering is performed by a pair of concave dies and in this material moves away from the centre this decreases the size of a slab.

QUESTION: 14

Cold shut (lap) may occur in products obtained by:

Solution:
QUESTION: 15

Identify the process in which the metal is shaped by means of intermittent blows on it

Solution:

Swaging is generally used for reducing the diameter, or tapering the end of bars and tube through rotating dies.

QUESTION: 16

Which one of the following processes is adopted for manufacturing of steel balls for ball bearing?

Solution:
QUESTION: 17

Which one of the following metal forming processes in not a high energy forming processes?

Solution:

In metal forming process, energy source such as chemical, magnetic and electrical discharge can be used. Since in ail such processes, the rate of energy flow is of much higher order, these are commonly called high-energy rate (HER) processes. Three common HER processes are:
1. Explosive forming
2. Electrohydraulic forming
3. Electromagnetic forming

QUESTION: 18

A forging method for reducing the diameter of a bar and in the process making it longer is termed as

Solution:
QUESTION: 19

The process of coining is

Solution:

Coining is cold forging operation.

QUESTION: 20

Which of the following manufacturing process will produce strongest component?

Solution:
QUESTION: 21

Which of the following metals is, best suitable for extrusion either hot or cold?

Solution:
QUESTION: 22

Collapsible tooth paste tubes are manufactured by

Solution:
QUESTION: 23

What does hydrostatic pressure in extrusion process improve?

Solution:

Hydrostatic pressure increases the ductility of the material. Therefore, brittle material can be extruded bv this method.

QUESTION: 24

In the metal extrusion process, when the.die angle increases, the required extrusion force

Solution:

As the die angle increases, the contact between the die and workpiece decreases which decreases the force required but when the die angle increases beyond a certain value, this creates hinderance in the flow of metal hence force required increases.

QUESTION: 25

Which metal forming process is used for manufacturing of long steel wire?

Solution:
QUESTION: 26

A floating mandrel is used in

Solution:

Tube drawing is done by
1. Tube sinking operation
2. Tube drawing with fixed mandrel
3. Tube drawing with floating mandrel
4. Tube drawing with moving mandrel

QUESTION: 27

Blanking and piercing operation can be performed simultaneously in

Solution:

In compound die, multiple operation can be performed in single stroke and sinaie operation.

Generally washers are made by this method.

QUESTION: 28

In piercing operation shear and clearance is provided on

Solution:

In piercing or punching punch is exact clearance is provided on die and shear is provided on punch.

QUESTION: 29

In blanking operation the clearance provided is

Solution:
QUESTION: 30

A sheet of metal is being cut along its length in a straight line such a cutting operation is called

Solution: