Description

This mock test of Traverse Surveying And Contouring - 2 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam.
This contains 9 Multiple Choice Questions for Civil Engineering (CE) Traverse Surveying And Contouring - 2 (mcq) to study with solutions a complete question bank.
The solved questions answers in this Traverse Surveying And Contouring - 2 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE)
students definitely take this Traverse Surveying And Contouring - 2 exercise for a better result in the exam. You can find other Traverse Surveying And Contouring - 2 extra questions,
long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.

QUESTION: 1

The direction of the magnetic meridian is established at each traverse station and the direction of the line is determined with reference to the magnetic meridian. This method of traversing is called

Solution:

In the loose needle method, the direction of the magnetic meridian is established at each traverse station and the direction of the line is determined with reference to the magnetic meridian. In other words, the magnetic bearing of each line is determined directly. A theodolite fitted with a compass is used for determining the magnetic bearing of the traverse line. The loose needle method is also known as free needle method.

QUESTION: 2

Which one of the following figures indicates the principle of traversing?

Solution:

The principles of traversing say that, a traverse should consist of a series of straight lines connected together to form an open or a closed polygon. The points, defining the ends of the traverse lines are called traverse stations or traverse points.

QUESTION: 3

If L is the perimeter of a closed traverse, ΔD is the closing error in departure, the correction for the departure of a traverse side of length L_{1}, according to Bowditch rule, is

Solution:

Correction of departure of a line according to Bowditch Rule =

⇒ = l_{1} traverse side length

∑l = total traverse side length

∑l = l_{1 }+ l_{2} + l_{3}....

given ∑l = L

∑D = total departure = -[ L_{1}/L x ΔD]

QUESTION: 4

If the coordinates bf A are 100 N and 200 E and those of Care 100 S end 200 E, then the length AC is

Solution:

QUESTION: 5

Contour interval is

Solution:

QUESTION: 6

Transit rule of balancing a traverse is applied when

Solution:

QUESTION: 7

Match List-I with List-II and select the correct answer using the codes given below the lists:

List-l

A. Equally spaced contour lines

B. Contours are always perpendicular to

C. Contours increase in elevation from inside to outside

D. Contours with horizontal equivalent zero

List-II.

1. Steepest slope

2. A vertical cliff

3. A saddle

4. A depression

5. Uniform slope

Solution:

Equally spaced contour lines are formed by uniform slope.

Contours are always perpendicular to the steepest slope.

A series of closed contours on map indicates a depression, if the higher values are outside.

Contours never run into one another except in the case of a vertical cliff. In the vertical cliff case, several contours coincide at a point and the horizontal equivalent becomes zero.

QUESTION: 8

The contours lines of different elevations can intersect in the case/cases of

1. Vertical diff

2. Cave

3. Over hanging diff

Solution:

QUESTION: 9

Which of the following methods of contouring is most suitable for a hilly terrain?

Solution:

### Compass and Traverse Surveying

Doc | 6 Pages

### Traverse Method, Surveying and Levelling

Doc | 1 Page

### Scalar Algorithms (Contouring)

Doc | 36 Pages

- Traverse Surveying And Contouring - 2
Test | 9 questions | 30 min

- Traverse Surveying And Contouring - 1
Test | 10 questions | 30 min

- Surveying - 2
Test | 20 questions | 60 min

- Surveying 2
Test | 20 questions | 12 min

- Surveying 2 MCQ
Test | 20 questions | 12 min