Description

This mock test of Pulse Modulation for GATE helps you for every GATE entrance exam.
This contains 10 Multiple Choice Questions for GATE Pulse Modulation (mcq) to study with solutions a complete question bank.
The solved questions answers in this Pulse Modulation quiz give you a good mix of easy questions and tough questions. GATE
students definitely take this Pulse Modulation exercise for a better result in the exam. You can find other Pulse Modulation extra questions,
long questions & short questions for GATE on EduRev as well by searching above.

QUESTION: 1

The Nyquist rate for a continuous-time signal (x) is

x(t) = 6cos50πt + 20sin300πt - 10cos100πt

Solution:

Given,

Also,

Comparing equations (I) and (II), we have:

Thus, the highest frequency component of the given message signal will be

∴ Nyquist rate = 2f_{max} = 2 x 150 = 300 Hz

QUESTION: 2

Which of the following pulse modulation systems is analog?

Solution:

PAM, PWM and PPM are examples of analog pulse modulation techniques while PCM is a digital pulse modulation.

QUESTION: 3

The Nyquist interval for the signal

Solution:

Given signal is

Hence, the maximum frequency present in x(t) is f_{1}= 2500 Hz

∴ Nyquist rate is given as

f_{s} = 2f_{m}

(where, f_{m} = Maximum frequency present in the signal)

Here, f_{m} = f_{1} = 2500 Hz

∴ Nyquist rate is

Nyquist interval is given as

QUESTION: 4

A telephone signal with cut-off frequency of 4 kHz is digitized into 8 bit PCM, sampled at Nyquist rate. The quantization S/N ratio is

Solution:

QUESTION: 5

A sine wave of frequency f_{m} and amplitude A_{m} is applied to a delta modulator having step size Δ. The slope overload distortion will not occur if

Solution:

Let, x(t) = A_{m} sin (2πf_{m}t)

The slope of x(t) will be maximum when derivative of x(t) w.r.t. 't' will be maximum.

Maximum slope = Δ/T_{s}

Hence, for slope overload distortion not to occur,

Hence, slope overload distortion doesn’t occur if

QUESTION: 6

The output signal to noise ratio (SNR) of a 10-bit PCM was found to be 30 dB. The desired SNR is 42 dB. It was decided to increase the SNR to the desired value by increasing the number of quantization levels. The percentage increase in the transmission bandwidth required for this SNR is

Solution:

Given, SNR = 30 dB, n = 10,

Desired value of SNR = 42 dB

With the increase in n by 1 bit, the value of SNR increases by 6 dB. Therefore, to increase the value of SNR by 12 dB, it is necessary to increase n by 2,

∴ n = 10 + 2 = 12

Now, BW of PCM system = 1/2 nf_{s}

Therefore, BW with n = 10 is

and BW for n = 12 is

QUESTION: 7

The biggest disadvantages of PCM is

Solution:

QUESTION: 8

The bandwidth of TV video plus audio signal is 4.5 MHz. If this signal is converted into PCM bit stream with 1024 quantization levels and the signal is sampled at the rate 20% above Nyquist rate, then the number of bits/sec of the resulting signal is

Solution:

Given,

Now, quantization level, q = 2^{n}

(n = No. of bits/sec)

∴ 2^{n} = 1024 = 2^{10 }

or, n = 10

QUESTION: 9

Assertion (A) : PCM has much better noise immunity as compared to PAM, PWM and PPM systems.

Reason (R) : PCM does not contain any information in the width or the position of the pulses.

Solution:

In practice, the transmitted pulses usually have slightly sloping sides (edges). As the noise is superimposed on them, the width and the position of the regenerated pulses is changed. This distorts the information contents in the PWM and PPM signals. Since PCM does not contain any information in the width or the position of the pulses, therefore PCM has much better noise immunity as compared to PAM, PWM and PPM systems. Hence, both assertion and reason are true and reason is the correct explanation of assertion.

QUESTION: 10

Assertion (A) : The signaling rate and transmission channel bandwidth is quite large for delta modulation compared to PCM.

Reason (R) : There is no analog to digital converter required in delta modulation unlike PCM.

Solution:

Since, the delta modulation transmits only one bit for one sample, therefore the signaling rate and transmission channel bandwidth is quite small for delta modulation compared to PCM, Hence, assertion is a false statement.

The transmission and receiver implementation is very simple for delta modulation since there is no A/D converter required in delta modulation unlike PCM. Hence, reason is a true statement.

### Pulse Modulation

Doc | 79 Pages

### Types of Pulse Modulation

Doc | 6 Pages

### Pulse Width Modulation

Video | 07:28 min

### Output capture Pulse Width Modulation Pulse Accumulation

Doc | 12 Pages

- Pulse Modulation
Test | 10 questions | 30 min

- Amplitude Modulation
Test | 10 questions | 30 min

- Angle Modulation
Test | 10 questions | 30 min

- Test: Amplitude Modulation
Test | 10 questions | 10 min

- Amplitude Modulation - MCQ Test
Test | 20 questions | 60 min