Civil Engineering (CE)  >  Civil Engineering SSC JE (Technical)  >  Technical Mock Test CE (SSC JE)- 14 Download as PDF

Technical Mock Test CE (SSC JE)- 14


Test Description

100 Questions MCQ Test Civil Engineering SSC JE (Technical) | Technical Mock Test CE (SSC JE)- 14

Technical Mock Test CE (SSC JE)- 14 for Civil Engineering (CE) 2023 is part of Civil Engineering SSC JE (Technical) preparation. The Technical Mock Test CE (SSC JE)- 14 questions and answers have been prepared according to the Civil Engineering (CE) exam syllabus.The Technical Mock Test CE (SSC JE)- 14 MCQs are made for Civil Engineering (CE) 2023 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Technical Mock Test CE (SSC JE)- 14 below.
Solutions of Technical Mock Test CE (SSC JE)- 14 questions in English are available as part of our Civil Engineering SSC JE (Technical) for Civil Engineering (CE) & Technical Mock Test CE (SSC JE)- 14 solutions in Hindi for Civil Engineering SSC JE (Technical) course. Download more important topics, notes, lectures and mock test series for Civil Engineering (CE) Exam by signing up for free. Attempt Technical Mock Test CE (SSC JE)- 14 | 100 questions in 100 minutes | Mock test for Civil Engineering (CE) preparation | Free important questions MCQ to study Civil Engineering SSC JE (Technical) for Civil Engineering (CE) Exam | Download free PDF with solutions
1 Crore+ students have signed up on EduRev. Have you?
Technical Mock Test CE (SSC JE)- 14 - Question 1

The effective slenderness ratio of a cantilever column is

Technical Mock Test CE (SSC JE)- 14 - Question 2

In a cantilever beam subjected to general loading, the maximum bending moment is at

Technical Mock Test CE (SSC JE)- 14 - Question 3

A bar having a cross-sectional area of 700 mm2 is subjected to axial loads at the positionsindicated. The value of stress in the segment QR is

Technical Mock Test CE (SSC JE)- 14 - Question 4

Ratio of length of column to the minimum radius of gyration of the cross-sectional area of thecolumn is known as

Technical Mock Test CE (SSC JE)- 14 - Question 5

A linear force-deformation relation is obtained in materials

Technical Mock Test CE (SSC JE)- 14 - Question 6

The property of a material by which it can be beaten or rolled into plates, is called

Technical Mock Test CE (SSC JE)- 14 - Question 7

In the cantilevel beam shown in the given figure δ2 is the deflection under × due to load w1 at T and δ1 is the deflection under Y due to load wdue to load w2 at x. The ratio of is


 

Technical Mock Test CE (SSC JE)- 14 - Question 8

The given figure shows a portal frame with one end fixed and other hinged. The ratio of the fixed end moments MBA/MCD due to side sway will be

Technical Mock Test CE (SSC JE)- 14 - Question 9

A lighthouse is visible jsut above the horizon at a certain station at the sea level. The distance b/w the station & the light house is 40km. The height of light house is approx.

Technical Mock Test CE (SSC JE)- 14 - Question 10

Technical Mock Test CE (SSC JE)- 14 - Question 11

The given figure shows a frame loaded with a single concentrated load P. The fixed-end moment developed at Support A will be

Technical Mock Test CE (SSC JE)- 14 - Question 12

Mean sea level at any place is the average datum of the hourly tide height observed over a periodof nearly

Technical Mock Test CE (SSC JE)- 14 - Question 13

If the sensitivity of the bubble tube of a level is 30" of arc per division, determine the disn of apoint at which the combined curvature and refraction correction become numerically equalto the error induced by dislevelment of 1 division of the level tube-

Technical Mock Test CE (SSC JE)- 14 - Question 14

If the sensitivity of a bubble tube of a levelling instrument is 30" per 2mm division. Find the error in the staff reading on a staff held at a distance 100m caused by the bubble being two divisions out of the centre.

Technical Mock Test CE (SSC JE)- 14 - Question 15

The following bearings were taken in running closed compass traverse ABCDA


One would suspect local attraction at stations

Technical Mock Test CE (SSC JE)- 14 - Question 16

How high should a helicopter pilot rise at a point A just to see the horizon at pt B if the distanceAB is 90km?

Technical Mock Test CE (SSC JE)- 14 - Question 17

A Parabolic vertical curve is to be set out connecting two uniform grade of +0.6% and +1.0%. The rate of change of grade is to be 0.06% per 30 minute. The lenth of curve will be.
 

Technical Mock Test CE (SSC JE)- 14 - Question 18

The method of plane tabling commonly used for establishing instrument station is the method of

Technical Mock Test CE (SSC JE)- 14 - Question 19

The process of determining the location of the station (on the map) occupied by plane table iscalled.

Technical Mock Test CE (SSC JE)- 14 - Question 20

If the cross-section areas of an embankment at 30 m. interval are 20, 40, 60, 50, 30 mrespectively, then the volume of embankment on the vasis of prismoidal rule.

Technical Mock Test CE (SSC JE)- 14 - Question 21

If one intends to obtain the best workability of concrete the prefered shape of aggregate is?

Technical Mock Test CE (SSC JE)- 14 - Question 22

According to the Indian Standard specifications, concrete should be cured under a humidity of?

Technical Mock Test CE (SSC JE)- 14 - Question 23

Fitness of cement is measured in the units of?

Technical Mock Test CE (SSC JE)- 14 - Question 24

What treatment is adopted for making timber fire resistant?

Technical Mock Test CE (SSC JE)- 14 - Question 25

As per IS classification the minimum compressive strength of a first class brick should be?

Technical Mock Test CE (SSC JE)- 14 - Question 26

Which of the following tests compare the dynamic modules of elasticity of sample ofconcrete?

Technical Mock Test CE (SSC JE)- 14 - Question 27

What is requirement of water (expressed as % of cement w/w) for complition of chemicalreaction in process of hydration of OPC.

Technical Mock Test CE (SSC JE)- 14 - Question 28

What is the ratio of flexural strength (fcr) to the characteristic compressive  strength of concrete (fck) for M25 grade concrete ?

Detailed Solution for Technical Mock Test CE (SSC JE)- 14 - Question 28

Technical Mock Test CE (SSC JE)- 14 - Question 29

Which one of the following is the correct statement? refractory bricks resist

Technical Mock Test CE (SSC JE)- 14 - Question 30

On which of the following is the working principle of concrete hammer for nondestructivetest based?

Technical Mock Test CE (SSC JE)- 14 - Question 31

On which one of the following factors, does strength of concrete depend primarily?

Technical Mock Test CE (SSC JE)- 14 - Question 32

In a tree, the cambium layer is situated between

Technical Mock Test CE (SSC JE)- 14 - Question 33

Transportation of concrete-mix by pumps is very convenient method, particularly in case of

Technical Mock Test CE (SSC JE)- 14 - Question 34

The timber preservative "Creosote" belongs to the group of

Technical Mock Test CE (SSC JE)- 14 - Question 35

The strength of timber is maximum ina direction

Technical Mock Test CE (SSC JE)- 14 - Question 36

A good quality undisturbed soil sample is one which is obtained using a sampling tube havingan area ratio of

Technical Mock Test CE (SSC JE)- 14 - Question 37

Which one of the following tests cannot be done without undisturbed sampling?

Technical Mock Test CE (SSC JE)- 14 - Question 38

A clayey soil has liquid limit = WL ; plastic limit WP and Natural moisture content = W. The
consistency under of the soil is given by
 

Technical Mock Test CE (SSC JE)- 14 - Question 39

The configuration of flow nets depends upon

Technical Mock Test CE (SSC JE)- 14 - Question 40

A sand deposit has a porosity of 0.375 and 9 specific gravity of 2.6. The critical hydraulicgradient for the sand deposit is

Technical Mock Test CE (SSC JE)- 14 - Question 41

A flownet for an earth dam on imperviousfoundation consists of 4 flow channels and 15 equipotential drops. The fall reservoir level is15m above the downstream horizontal permeability is 9×10-6m/s and verticalpermeability is 1×10-6m/ s , The quantity ofseepage through the dam will be

Technical Mock Test CE (SSC JE)- 14 - Question 42

Saturated and dry densities of 9 soil are respectively 2000 Kg/m3 and 1500kg/m3. Thewater content (in percentage) of the soil in the saturated state would be

Technical Mock Test CE (SSC JE)- 14 - Question 43

If a soil sample of weight 0.15Kg having 9volume of 10–4 m3 and dry unit wt. of 1600Kg/m3 is mixed with 0.02 Kg of water then thewater content in the sample will be

Technical Mock Test CE (SSC JE)- 14 - Question 44

If an unconfined compressive strength of 4 Kg/ cm2 in the natural state of clay reduced by fourtimes in the remoulded state, then its sensitivitywill be

Technical Mock Test CE (SSC JE)- 14 - Question 45

In a direct shear test, the shear stress and normla stress on a dry sand sample at failureare 0.6Kg/cm2 and 1Kg/cm2 respectively. The angle of internal friction of the sand will benearby

Technical Mock Test CE (SSC JE)- 14 - Question 46

If an infinite slope of clay at a depth 5m has cohesion of 1 t/m2 and unit wt. of 2t/m3. Thenthe stability number will be

Technical Mock Test CE (SSC JE)- 14 - Question 47

Given that  C = 2t/m2, φ= 0° and Y = 2t/m3   the depth of tension crack developing in a cohesiveback fill would be

Technical Mock Test CE (SSC JE)- 14 - Question 48

Which one of the following fairs are not related directly to each other?

Technical Mock Test CE (SSC JE)- 14 - Question 49

As per terzaghi's equation, the bearing capacity of strip footing resting on cohesive Soil (c = 10KN/m2) For unit depth and unit width (assume NC as 5.7) is

Detailed Solution for Technical Mock Test CE (SSC JE)- 14 - Question 49


= 10 x 5.7 = 57

Technical Mock Test CE (SSC JE)- 14 - Question 50

For four free standing pile group having are tan value of 18.3, the efficiency as per converselabarre formula, would be

Technical Mock Test CE (SSC JE)- 14 - Question 51

Deflections can be controlled by using the appropriate

Technical Mock Test CE (SSC JE)- 14 - Question 52

In limit state approach spacing of main reinforcement controls primarily

Technical Mock Test CE (SSC JE)- 14 - Question 53

Unequal top and bottom reinforcement in a reinforced concrete section leads to

Technical Mock Test CE (SSC JE)- 14 - Question 54

Unequal top and bottom reinforcement in a reinforced concrete section leads to

Detailed Solution for Technical Mock Test CE (SSC JE)- 14 - Question 54

(b)

When there is unequal top and bottom reinforcement in RC section, dfifferential strains are induced cross section  with the location with having reinforcement shrinking more than the location with high reinforcement, leading to shrinkage deflection.

Technical Mock Test CE (SSC JE)- 14 - Question 55

A 200 mm thick brick masonary wall made of modular brick carries an axial load of 30 kN/m from wall above and an eccentric load of 20 kN/m from RCC floor acting at a distance of47.5 mm from the centre line of the wall. The resultant eccentricity will be

Technical Mock Test CE (SSC JE)- 14 - Question 56

The reduction coefficient of a reinforced concrete column with an effective length of 4.8m and size 250 × 300 mm is

Technical Mock Test CE (SSC JE)- 14 - Question 57

Given that d=effective depth i b=width and D=overall depth, the maximum area ofcompression reinforcement in a beam is

Technical Mock Test CE (SSC JE)- 14 - Question 58

The final deflection due to all loads including the effects of temperature, creep and shrinkageand measured from as-cast level of supports of floors, roofs and all other horizontal membersshould NOT exceed.

Technical Mock Test CE (SSC JE)- 14 - Question 59

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can beused is

Technical Mock Test CE (SSC JE)- 14 - Question 60

For a prestressed concrete bridge beam, a minimum clear spacing of the cable or group ofcables should be

Technical Mock Test CE (SSC JE)- 14 - Question 61

If the conjugate depths before and after the jump are 0.5 m and 2.5 m respectively. then loss ofenergy in hydraulic jump will be

Technical Mock Test CE (SSC JE)- 14 - Question 62

Froude number is the ratio of inertia force to -

Technical Mock Test CE (SSC JE)- 14 - Question 63

Pressure coefficient is ratio of pressure force to

Technical Mock Test CE (SSC JE)- 14 - Question 64

The higest velocity in (cm/sec) for flow of water of viscosity 0.01 poise to be laminar in a 6mmpipe is

Technical Mock Test CE (SSC JE)- 14 - Question 65

With increasing ageing of pipes, the proportion between the maximum velocity and meanvelocity

Technical Mock Test CE (SSC JE)- 14 - Question 66

Sludge bulking can be controlled by which of the following effectively

Technical Mock Test CE (SSC JE)- 14 - Question 67

Aerosol is-

Technical Mock Test CE (SSC JE)- 14 - Question 68

Which one of the following methods can be employed for plastic and rubber wastedisposal?

Technical Mock Test CE (SSC JE)- 14 - Question 69

In the plot of residual chlorine versus chlorine dose applied shown in the above figure, thecurve will not have any (o, o) point because

Technical Mock Test CE (SSC JE)- 14 - Question 70

If the methyl orange alkalinity of water equals or exceeds total hardness, all of the hardnessis

Technical Mock Test CE (SSC JE)- 14 - Question 71

The Second stage BoD is due to

Technical Mock Test CE (SSC JE)- 14 - Question 72

Sewage sickness is due to a term used for

Technical Mock Test CE (SSC JE)- 14 - Question 73

The trap used for a water closet is called-

Technical Mock Test CE (SSC JE)- 14 - Question 74

A rural water supply scheme seves a population of 10,000 at the rate of 50 litres per capity perday, for the chlorine dose of 2 ppm, the required amount of bleaching powder with 20% available chlorine will be

Technical Mock Test CE (SSC JE)- 14 - Question 75

Reciprocating pumps are suitable for

Technical Mock Test CE (SSC JE)- 14 - Question 76

Given that the base period is 100 days and the duty of canal is 1000 hectares per comec, thedepth of water will be

Technical Mock Test CE (SSC JE)- 14 - Question 77

As per Lacey’s theory, the silt factor is_________________?

Detailed Solution for Technical Mock Test CE (SSC JE)- 14 - Question 77

As per Lacey's theory, the silt factor is directly proportional to square root of average particle size.

Technical Mock Test CE (SSC JE)- 14 - Question 78

The following data were recorded from an irrigatefiled

1. Field capacity = 20%

2. Permanent wilting capacity = 10%

3. permissible depletion of available soilmoisture = 50%

4. Dry unit weight of soil = 1500kgf/m3

5. Effective rainfall : 25mm

Based on these data the net irrigationrequire per meter depth of soil will be

Technical Mock Test CE (SSC JE)- 14 - Question 79

If the depth is 8.64 cm on a field over a base period of 10 days, then the duty is

Detailed Solution for Technical Mock Test CE (SSC JE)- 14 - Question 79

Technical Mock Test CE (SSC JE)- 14 - Question 80

The lacey's silt factor for a particular alluviam is 2.0. This alluviam would comprise

Technical Mock Test CE (SSC JE)- 14 - Question 81

Web crippling generally occurs at the point where

Technical Mock Test CE (SSC JE)- 14 - Question 82

The cross-section of a standard gillt is a triangle whose base angles are

Technical Mock Test CE (SSC JE)- 14 - Question 83

In a fillet weld placed on the sides of the base the metal experiences.

Technical Mock Test CE (SSC JE)- 14 - Question 84

The Indian standard code which deals with steel structure is

Technical Mock Test CE (SSC JE)- 14 - Question 85

A major beam in a building structure, is known as

Technical Mock Test CE (SSC JE)- 14 - Question 86

For steel membey not exposed to weather, the thickness of steel should not be less than

Technical Mock Test CE (SSC JE)- 14 - Question 87

A column splice is used to increase

Technical Mock Test CE (SSC JE)- 14 - Question 88

An imaginary line along which wivets are placed, is known as

Technical Mock Test CE (SSC JE)- 14 - Question 89

Sometimes a carriage way is reserved for use by high speed power driven vehicles only, called

Technical Mock Test CE (SSC JE)- 14 - Question 90

The road connecting capital cities of states is called

Technical Mock Test CE (SSC JE)- 14 - Question 91

The road length per hundre square kilometres in India is

Technical Mock Test CE (SSC JE)- 14 - Question 92

A flyover Segregates traffic with respect to

Technical Mock Test CE (SSC JE)- 14 - Question 93

A circumferential road, built ground an urban area to enable free flow of traffic is called

Technical Mock Test CE (SSC JE)- 14 - Question 94

A carriage way in which a cement concrete wearing surface is provided for the wheel tracxks only, is called

Technical Mock Test CE (SSC JE)- 14 - Question 95

One cubic meter of mild steel weighs about?

Technical Mock Test CE (SSC JE)- 14 - Question 96

Of the total estimation cost of a building, electrification usually account for

Technical Mock Test CE (SSC JE)- 14 - Question 97

Which one of the following is not the common size of steel bar ?

Technical Mock Test CE (SSC JE)- 14 - Question 98

Thickness of plastering is usually?

Technical Mock Test CE (SSC JE)- 14 - Question 99

Whenever not specified the number of hold fasts for door is usually taken as ?

Technical Mock Test CE (SSC JE)- 14 - Question 100

The process of evaluating the rough cost of construction of a project is known as 0?

Use Code STAYHOME200 and get INR 200 additional OFF
Use Coupon Code
Information about Technical Mock Test CE (SSC JE)- 14 Page
In this test you can find the Exam questions for Technical Mock Test CE (SSC JE)- 14 solved & explained in the simplest way possible. Besides giving Questions and answers for Technical Mock Test CE (SSC JE)- 14, EduRev gives you an ample number of Online tests for practice