Mock Test: SSC JE (ME)- 10
100 Questions MCQ Test Mechanical Engineering SSC JE (Technical) | Mock Test: SSC JE (ME)- 10
| 1 Crore+ students have signed up on EduRev. Have you? |
The heat and work are mutually convertible. This statement is called ......law of thermodynamics.
The amount of heat required to raise the temperature of 1 kg of water through one kelvin in called
A process, in which the gas is heated or expanded in such a way that the product of its pressure and volume remains constant, is called
In a quasi equilibrium process, the pressure in a system
The figure as shown below is the variation of the pressure of a gas with temperature (not volume) a given mass of an idea gas is subjected to various process starting from the state represented by point A. Which graph does an isochoric process represent
Which is usually the costliest item in a refrigeration system ?
COP of a domestic refrigerator in comparison to domestic air conditioner will be
When the lower temperature of a refrigerating machine is fixed, then the coefficient of performance can be improved by
The difference between dry bulb temperature ad wet bulb temperature, is called
used for calculatingIn a petrol engine, the fuel supplied to the engine cylinder is mixed with required quantity of air and the mixture is ignited with a
In a four stroke cycle diesel engine, the exhaust valve
The probability of knocking in diesel engines is increased by
The nuclear radiators produced in a reactor which must be shielded are
In a SI engine very high compression ratio cannot be used because
For practical purposes ethyl fluid is used to increase the octane rating of the fuel.
The incomplete combustion is indicated by the presence of
Power required by fan in forced draught is ...... to that of induced draught
Which of the following component is not subjected to high-pressure high-temperature steam ?
The amount of water evaporated in kg per kg of fuel burnt is called
In a glass tube type water indicator for a boiler, one end of the tube is connected to water space and the other end is connected to
Lancashire Boiler is a horizontal type and stationary fire tube boiler.
There are two types of a fire-tube boiler which are Internally & Externally fired boilers.
Babcock and Wilcox Boiler was discovered by George Herman Babcock and Stephen Wilcox in the year 1967. This is a water tube boiler, used in steam power plants. In this type of boiler, water is circulated inside the tubes and hot gases flow over the tubes.
The Mercury is known as non-wetting liquid because it does not wet the surface. The Mercury posses this property due to
Correct Answer :- a
Explanation : Capillarity is the property of both cohesion and adhesion. But surface tension is due to cohesion only it does not involve adhesion. As cohesive force is higher than adhesion in mercury it does not wet the glass.
Which one of the following is a typical example of non-newtonian fluid of Pseudo plastic variety
Fluid is a substance which offers no resistance to change of
Navier-Stoke's equation represents the conservation of
When the pressure intensity at a point is more than the local atmospheric pressure, then the difference of these two pressure is called
The point at which the resultant pressure on an immersed surface acts, is known as
The discharge through a venturimeter is given by
where Cd = Coefficient of discharge,
a1 = Area at inlet,
a2 = Area at throat, and
h = Venturi -head
Correct Answer :- b
Explanation : Within a multistage centrifugal pump, each impeller acts like a single-stage pump within a chain of pumps. As the liquid is propelled from one impeller to the next within the pump’s housing, the pressure of the liquid continuously increases as it passes through until it exits the pump.
By relying on multiple impellers to distribute the pressure-building load of the pump, multistage centrifugal pumps can generate greater power and pressure with smaller motors, using less energy.
The biggest advantage of centrifugal pumps is their aforementioned simplicity. They don't require any valves, or many moving parts. This makes them easy to produce with many different materials. It also allows them to move at high speeds with minimal maintenance.
The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
The forces, whose lines of action are parallel to each other and act in the same directions, are known as
Non -coplaner concurrent forces are those forces which
The angle of inclination of the plane at which the body begin to move down the plane is called
The angle of inclination of the plane at which the body begins to move down the plane, is called angle of repose.
A leader is resting on a rough ground and leaning against a smooth vertical wall. The force of friction will act
The ratio of change in volume to the original volume is called
A localised compressive stress at the area of contact between two members is known as
The bending moment on a section is maximum where shear force is
Correct Answer :- c
Explanation : Both zero and changes sign is the correct answer. Because when sf changes sign from max to min or vice versa, it will come to a point when sf will be zero.
So according to the given options "changes sign" is the correct answer.
The maximum bending moment of a simply supported beam of span l and carrying a pointloadW at the centre of beam, is
When a body is subjected to three mutually perpendicular stresses, of equal intensity, the ratio of direct stress to the corresponding volumetric strain is known as
A material capable of absorbing large amount of energy before fracture is known as
If a shaft is rotating at N revolutions per minute with an applied torque T N-m, the power being transmitted by the shaft in watt is
For a circular shaft of diameter d subjected to torque T, the maximum value of the shear stress
is
The steel bars in reinforced cement concrete beam are located at
A simply supported beam of span L carries a point load P at the mid span. The downward deflection under the load will be
The motion transmitted between the teeth of two spur gears is generally
The condition for correct steering of a Davis steering gear is
where a = Angle of inclination of the links to the vertical
The metal suitable for bearings subjected to light loads is
The metal suitable for bearings subjected to light loads is phosphor bronze.
The process which improves the machinability of steels, but lowers the hardness and tensile strength is
The ratio of endurance limit in shear to the endurance limit in flexure is
A thin spherical shell of internal diameter d is subjected to an internal pressure p. If st is the tensile stress for the shell material, then thickness of shell is equal to
Correct Answer :- d
Explanation : In case of thin spherical shell hoop and longitudinal stresses are same as here length and dia are not two separate things. Both are equal. That's why when we equal resisting stress to the stress due to internal pressure same value is obtained for hoop and longitudinal.
The centre to centre distance between two consecutive rivets in a row, is called
Ceramic cutting tool chip are fixed to the tool body by
Which of the following is an example of rothogonal cutting ?
The soldering process is carried out in the temperature range
Which of the following welding techniques uses a nonconsumable electrode ?
A casting defect which occurs near the ingrates as rough lumps on the surface of a casting is known as
The high cutting speed and large rake angle of the tool will result in the formation of
|
6 videos|97 docs|55 tests
|
|
Use Code STAYHOME200 and get INR 200 additional OFF
|
Use Coupon Code |
|
6 videos|97 docs|55 tests
|
Download free EduRev App
Related content with Mock Test: SSC JE (ME)- 10
|
|
|
|
Related tests with Mock Test: SSC JE (ME)- 10
|
|
|
|
|
|
© EduRev
|
Education Revolution
|
Follow Us
|
