Mock Test: SSC JE (ME)- 12
100 Questions MCQ Test Mechanical Engineering SSC JE (Technical) | Mock Test: SSC JE (ME)- 12
| 1 Crore+ students have signed up on EduRev. Have you? |
Which of the following conditions are favourable for liquefaction of a gas?
The work done in a reversible adiabatic process from state 1 to states 2 is given by
The Characteristic equation of gases PV = nRT holds good for
In thermodynamics analysis, a pure substance is that which
The measurement of a thermodynamic property known as temperature is based on
The behaviour of super heated vapour is similar to that of
The processes occurring in open system which permit the transfer of mass to and from the system, are known as
A process, in which the working substance neither receives nor gives out heat to its surroundings during its expansion or compression, is called
Which is usually the costliest item in a refrigeration system ?
An external gear with 60 teeth meshes with a pinion of 20 teeth, module being 6 mm. What is the centre distance in mm ?
Main advantage of a two- stroke engine over four-stroke engine is
Compression ratio in case of CI engine is in the range of
For an Otto cycle, the increase in compression ratio leads to
In thermal power plants, the dearator is used mainly to
Which device is used in thermal power plants to reduce level of pollution?
Which one of the following is NOT and accessory for the boiler ?
Match List-I (Type of boiler) with List-II (Features) select the correct answer using the
codes given below the lists:
List-I
a. Benson
b. Stirling
c. Babcock-Wilcox
d. Cochran
List-II
1. Vertical fire tube
2. Horizontal fire tube
3. Bent water tube
4. Once through flow
5. Inclined water tube
In parson's turbine ifa is nozzle angle, then what is the maximum efficiency of the turbine
The critical pressure ratio for maximum discharge through a nozzle is given by
The time of oscillation of a floating body with increase in metacentric height will be
All the terms of energy of Bernoulli's equation have dimension of
If a set of pipes described by (L1, D1, f1), (L2,D2,f2)....... are connected in series then an
equivalent pipe (Le, De,fe) is related as
If a set of pipes described by (L1, D1, f1), (L2,D2,f2)....... are connected in series then an
equivalent pipe (Le, De,fe) is related as
An open channel of symmetric right angled triangular cross-section is conveying a discharge Q. Taking gas the acceleration due to gravity,what is the critical depth ?
Match List I (Physical properties of fluid) with List II (Dimensions/definitions) and select the
correct answer using the codes given below the lists
The Bernoulli's equation is based on the assumption that
The discharge through an external mouthpiece is given by
The total energy line lies over the hydraulic gradient line by an amount equal to the
A fluid whose viscosity does no change with the rate of deformation of shear strain is known as
A fluid which obeys the Newton's law of viscosity is termed as
The point of contraflexure in a beam is at the location where the
Consider the simply supported beam AB subjected to the point loads of equal magnitudeas shown in the diagram below:
Which one of the following statement is correct?The position CD of the beam is
A cantilever beam of rectangular cross-section is subjected to a concentrated load at its free end. The state of stress at a point P on the centroidal longitudinal axis of beam is given by
If the principal stresses on a plane stress problem are s1 = 100 MPa and s2 = 40 MPa, then themagnitude of shear stress (in MPa) will be
A thin cylindrical shell of internal diameter d and thickness 't' is subjected to internal pressure 'p'. The change in diameter is given by
The ratio of bulk modulus to Young's modulus for a Poisson's ratio of 0.25 will be
Within elastic limit, shear stress is ......... shear strain.
The linear velocity of a body rotating atw rad/ s along a circular path of radius r is given by
A pendulum which executes one beat per second is known as
The ideal angle of banking provided on the curves on roads depends upon
The piston rod and the cross head in a steam engine are usually connected by means of
Match List-I (Application) with List-II (Joint) and select the correct answer using the code
given below the lists:
The endurance limit i.e., resistance to fatigue of a machine element can be improved by
In cyclic loading, stress concentration is more serious in
In case of pressure vessels having open ends, the fluid pressure induces
According to Unwin's formula, the relation between the diameter of rivet hole (d) and the thickness of plate (t) is given by
The difference between addendum and dedendum is known as
Which of the following machines does not require a flywheel ?
For a governor running at constant speed, what is the value of the force acting on the sleeve
The pair is known as a higher pair, when the relative motion between the elements of a pair is
Cutting tool material 18-4-1 HSS has which one of the following composition
Milling operation which produces flat vertical surfaces on both side of a work piece is known as
Which of the following material is best cut by oxy-cutting process ?
The temperature of the heat produced by an arc is around
When a steel containing more than 0.8% carbon in cooled slowly below the lower critical point, it consists of
In oblique cutting system, the cutting edge of the tool
|
6 videos|97 docs|55 tests
|
|
Use Code STAYHOME200 and get INR 200 additional OFF
|
Use Coupon Code |
|
6 videos|97 docs|55 tests
|
Download free EduRev App
Related content with Mock Test: SSC JE (ME)- 12
|
|
Related tests with Mock Test: SSC JE (ME)- 12
|
|
|
|
|
|
© EduRev
|
Education Revolution
|
Follow Us
|
