Test: Machine Design- 2

# Test: Machine Design- 2

Test Description

## 25 Questions MCQ Test Mechanical Engineering SSC JE (Technical) | Test: Machine Design- 2

Test: Machine Design- 2 for Mechanical Engineering 2023 is part of Mechanical Engineering SSC JE (Technical) preparation. The Test: Machine Design- 2 questions and answers have been prepared according to the Mechanical Engineering exam syllabus.The Test: Machine Design- 2 MCQs are made for Mechanical Engineering 2023 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Test: Machine Design- 2 below.
Solutions of Test: Machine Design- 2 questions in English are available as part of our Mechanical Engineering SSC JE (Technical) for Mechanical Engineering & Test: Machine Design- 2 solutions in Hindi for Mechanical Engineering SSC JE (Technical) course. Download more important topics, notes, lectures and mock test series for Mechanical Engineering Exam by signing up for free. Attempt Test: Machine Design- 2 | 25 questions in 50 minutes | Mock test for Mechanical Engineering preparation | Free important questions MCQ to study Mechanical Engineering SSC JE (Technical) for Mechanical Engineering Exam | Download free PDF with solutions
 1 Crore+ students have signed up on EduRev. Have you?
Test: Machine Design- 2 - Question 1

### Which category of V-Belts has maximum power transmission capability

Test: Machine Design- 2 - Question 2

### A wire rope is designated as 6 × 7. The number 6 represents.

Test: Machine Design- 2 - Question 3

### When a gear and pinion are made of same material the design is based on.

Test: Machine Design- 2 - Question 4

Which of the following is an assumption in equation.

Test: Machine Design- 2 - Question 5

It t = Thickness of teeth, h = height of teeth m = module of gear, lewis form factor is given by

Test: Machine Design- 2 - Question 6

The velocity factor for a gear having pitch line velocity of 15 m/s2 is given as.

Test: Machine Design- 2 - Question 7

The friction radius for designing a clutch with uniform pressure theory is given as

Test: Machine Design- 2 - Question 8

For a multiplate clutch with number of driving flange = 3 and no. of driven flange = 2 no. of contact surface is.

Detailed Solution for Test: Machine Design- 2 - Question 8

In a multi plate clutch, number of pairs of contact surfaces (n) is equal to n1 + n2 – 1. Due to the high number of pairs of contact surfaces, the torque transmitted is higher.
n is always a whole number.

Test: Machine Design- 2 - Question 9

For an engine which cannot start when loaded the type of clutch that should be used is

Test: Machine Design- 2 - Question 10

In two wheelers (eg mopeds) the type of clutch used is

Test: Machine Design- 2 - Question 11

An axle is subjected to.

Test: Machine Design- 2 - Question 12

Generally in design of shaft and key which of the following is made weak.

Test: Machine Design- 2 - Question 13

Which of the following is an example of flexible coupling
1. oldham's coupling
2. Muff coupling
3. Hooke's joint
4. flange coupling

Test: Machine Design- 2 - Question 14

Maximum shear stress theory is also known as

Test: Machine Design- 2 - Question 15

Which of the following theory is most suitable for brittle materials

Test: Machine Design- 2 - Question 16

For combines stress condition with bending moment = M and Twisting moment = T equivalent bending moment is given as.

Test: Machine Design- 2 - Question 17

If µ - heat cone angle f = Friction angle then in a cone clutch grabbing occurs when

Test: Machine Design- 2 - Question 18

At low speed which of the following has lowest frictional resistance.

Test: Machine Design- 2 - Question 19

A double cover plate butt joint will fail due to

Test: Machine Design- 2 - Question 20

The angle of inclination between two teeths in a acme thread is

Test: Machine Design- 2 - Question 21

Centrifugal tension should be considered in a belt drive when pitch line velocity is

Test: Machine Design- 2 - Question 22

Compound belt drive are used for.

Test: Machine Design- 2 - Question 23

For old clutches, designing is based on

Test: Machine Design- 2 - Question 24

The type of joint used between piston rod and cross head is

Test: Machine Design- 2 - Question 25

Which of the following is not a permanent joint

## Mechanical Engineering SSC JE (Technical)

6 videos|97 docs|55 tests
 Use Code STAYHOME200 and get INR 200 additional OFF Use Coupon Code
Information about Test: Machine Design- 2 Page
In this test you can find the Exam questions for Test: Machine Design- 2 solved & explained in the simplest way possible. Besides giving Questions and answers for Test: Machine Design- 2, EduRev gives you an ample number of Online tests for practice

## Mechanical Engineering SSC JE (Technical)

6 videos|97 docs|55 tests