Test: Mechanical Engineering- 14


100 Questions MCQ Test Mechanical Engineering SSC JE (Technical) | Test: Mechanical Engineering- 14


Description
This mock test of Test: Mechanical Engineering- 14 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam. This contains 100 Multiple Choice Questions for Mechanical Engineering Test: Mechanical Engineering- 14 (mcq) to study with solutions a complete question bank. The solved questions answers in this Test: Mechanical Engineering- 14 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering students definitely take this Test: Mechanical Engineering- 14 exercise for a better result in the exam. You can find other Test: Mechanical Engineering- 14 extra questions, long questions & short questions for Mechanical Engineering on EduRev as well by searching above.
QUESTION: 1

Molal specific heats of an ideal gas depend on

Solution:
QUESTION: 2

There is no work transfer involved in this process

Solution:
QUESTION: 3

A carnot engine operates between 27ºC and 327ºC. If the engine produces 300 kj of work,what is the entropy change during heat addition ?

Solution:
QUESTION: 4

Three engines A, B and Coperating on Argon, Oxygen and Air respectively. Which engine will have higher efficiency ?

Solution:
QUESTION: 5

At critical point the enthalpy of vaporization is

Solution:
QUESTION: 6

Increase in entropy of a system represents

Solution:
QUESTION: 7

The knocking tendency in compression ignition engines increase with

Solution:

In SI engineknocking tendency increases with increase in compression ratio. In CI engineknocking tendency decreases with increase in compression ratio and vice versa. If compression ratio is low in CI engine, there will not be enough temperature generation for ignition of the fuel air mixture.

QUESTION: 8

The cetane number of automotive diesel fuel used in India is in which one of the following ranges ?

Solution:
QUESTION: 9

The delay period in CI engine depends upon which of the following ?

Solution:
QUESTION: 10

What is the cause of reheat factor in a steam turbine ?

Solution:
QUESTION: 11

Blade erosion in steam turbines takes place

Solution:
QUESTION: 12

Mobility of statically indeterminate structure is

Solution:
QUESTION: 13

The path of contact in involute gears is

Solution:
QUESTION: 14

Mitre gears are used for

Solution:
QUESTION: 15

Bevel gears have their teeth

Solution:
QUESTION: 16

Which one of the following governor is widely used in Gramophone

Solution:
QUESTION: 17

Which of the following are antifriction bearing

Solution:
QUESTION: 18

Bearing used for heavy loads are

Solution:
QUESTION: 19

Hydrostatic law of pressure is given as

Solution:
QUESTION: 20

A 70 kg person walks on snow with a total foot implant area of 500 cm2. What pressure doeshe exert on snow ?

Solution:
QUESTION: 21

The centre of buoyancy is

Solution:
QUESTION: 22

During floods, water entered an office having wooden tables. The position of tables, if floating,will be

Solution:
QUESTION: 23

While using boundary layer equations, Bernoulli's equation

Solution:
QUESTION: 24

The Euler's equation of motion is a statement of

Solution:
QUESTION: 25

Which one of the following is measured by a rotameter ?

Solution:
QUESTION: 26

The number of elastic constant for a completely anisotropic elastic material are

Solution:
QUESTION: 27

The number of elastic constant for a orthotropic material are

Solution:
QUESTION: 28

What is the relationship between the linear elastic properties young's modulus (E), rigidity modulus (G) and bulk modulus (K) ?

Solution:
QUESTION: 29

Slenderness ratio is defined as the ratio of

Solution:
QUESTION: 30

The slenderness ratio of a section is

Solution:
QUESTION: 31

Euler's formula holds good only for

Solution:
QUESTION: 32

A thin cylindrical shell of diameter d, length L and thickness t is subjectd to an internal pressure
p. What is the ratio of longitudinal strain to hoop strain in terms of Poission's ratio (1/m) ?

Solution:
QUESTION: 33

The volumetric strain in case of a thin cylindrical shell of diameter d, thickness t, subjected to
internal pressure p is

Solution:
QUESTION: 34

The correct sequence of elements of 18-4=1 HSS tool is

Solution:
QUESTION: 35

In relation VTn = C, the value of n, for ceramic tools

Solution:
QUESTION: 36

Ceramic cutting tool chip are fixed to the tool body by

Solution:
QUESTION: 37

Bolt heads are manufactured by

Solution:
QUESTION: 38

Generally the value of point angle of a drill is

Solution:
QUESTION: 39

The different speeds on lathe are provided in

Solution:
QUESTION: 40

The two parts of a sand casting mould are called

Solution:
QUESTION: 41

Fluidity is greatly influenced by

Solution:
QUESTION: 42

In D.C. reverse polarity arc welding

Solution:
QUESTION: 43

In which of the following welding techniques in vacuum environment required

Solution:
QUESTION: 44

Which one of the following welding processes consists of minimum heat affected zone

Solution:
QUESTION: 45

Which one of the following is not an electric resistance method of welding

Solution:
QUESTION: 46

A medium carbon steel workpiece is turned on a lath at 50 m/ min cutting speed, 0.8 mm/ revfeed and 1.5 mm depth of cut, what is the rate of metal removal

Solution:
QUESTION: 47

In a typical metal cutting operation, using a cutting tool of positive rake a = 10º. It was observed that the shear angle was 20º the friction angle is

Solution:
QUESTION: 48

Primary tool force used in calculating the total power consumption in machining is

Solution:
QUESTION: 49

When the molten metal is poured in a mould, it may pass through the following items in sequence

Solution:
QUESTION: 50

A trepanning tool is used on

Solution:
QUESTION: 51

In solidification of metal during casting, compensation for solid contraction is

Solution:
QUESTION: 52

When trying to turn a key into a lock, following is applied

Solution:
QUESTION: 53

Properties of substances like pressure, temperature and density , in thermodynamic coordinates are

Solution:
QUESTION: 54

A perpetual motion machine is

Solution:
QUESTION: 55

Air refrigerators work on

Solution:
QUESTION: 56

Second law of thermodynamics defines

Solution:
QUESTION: 57

An isentropic process on T-S diagram is represented by a

Solution:
QUESTION: 58

The area under curve on T-S diagram represents the

Solution:
QUESTION: 59

Dynamic viscosity (m) has the dimensions as

Solution:
QUESTION: 60

The co-efficient of discharge (Cd) in terms of Cv and Cc is

Solution:
QUESTION: 61

For viscous flow between two parallel plates, the pressure drop per unit length is equal to

Solution:
QUESTION: 62

Total energy line (T.E.L) represents the sum of

Solution:
QUESTION: 63

Hydraulic gradient line (H.G. L.) represents the sum of

Solution:
QUESTION: 64

The loss of head due to sudden contraction of a pipe is equal to

Solution:
QUESTION: 65

The property of a material by virtue of which a body returns to its original shape after removal of the load is called

Solution:
QUESTION: 66

The ratio of direct stress to volumetric strain in case of a body subjected to three mutually perpendicular stresses of equal intensity, is equal to

Solution:
QUESTION: 67

The dimension of young's modulus of elasticity is given by

Solution:
QUESTION: 68

Match the items in columns I and II

Solution:
QUESTION: 69

There are two points P and Q on a planar rigid body. The relative velocity between the two points

Solution:

QUESTION: 70

In the figure shown, the relative velocity of link 1 with respect of link 2 is 12m/ sec. Link 2 rotates at a constant speed of 120 rpm. The magnitude of Coriolis component of acceleration of link 1 is

Solution:
QUESTION: 71

Axial thrust is minimum in case of

Solution:
QUESTION: 72

Gearing contact is which one of the following ?

Solution:
QUESTION: 73

If the two pulleys in a belt drive have different values of coefficient of friction, then the design will be based on the pulley for which

Solution:
QUESTION: 74

Alloy containing Tin is

Solution:
QUESTION: 75

The ductility of a material with work hardening

Solution:
QUESTION: 76

Which among the following is slowest speed operation in lathe

Solution:
QUESTION: 77

Soft materials can not be economically grinded due to

Solution:
QUESTION: 78

Feed rate in milling operation is expressed as

Solution:
QUESTION: 79

The machining process which makes a stepped cylindrical recess at the top of a hole to accommodate bolt head is called

Solution:
QUESTION: 80

Internal and external threads of different pitches can be produced by

Solution:
QUESTION: 81

The casting defect which is not caused by the high pouring temperature of melt is

Solution:
QUESTION: 82

The impurities in true centrifugal casting

Solution:
QUESTION: 83

In a gas welding of mild steel using an neutral flame the total amount of acetylene consurmed is 10 litre. the oxygen consumption is

Solution:
QUESTION: 84

Pinch effect in welding is the result of

Solution:
QUESTION: 85

The maximum heat in resistance welding is at the

Solution:
QUESTION: 86

If a i is the rake angle of the cutting tool f is the shear angle and V is the cutting velocity, velocity of chip sliding along the shear plane is given by

Solution:
QUESTION: 87

The size of inlet valve of an engine in comparison to exhaust valve is

Solution:
QUESTION: 88

The domestic refrigerator uses following type of compressor

Solution:
QUESTION: 89

The adiabatic equation of a perfect gas is

Solution:
QUESTION: 90

The forces which meet at one point, but their lies of action do not lie in a plane are called

Solution:

Concurrent Non coplanar forces

Ø In this system, all forces do not lie in the same plane, but their line of action passes through a single point ( O ).

Ø  Any two forces of a concurrent force system determine a plane, their resultant is determined by parallelogram law.

QUESTION: 91

A perfact gas

Solution:
QUESTION: 92

The buoyancy depends on

Solution:
QUESTION: 93

Euler's dimensionless number relates the following

Solution:
QUESTION: 94

Liquids transmit pressure equally in all the directions. This is according to

Solution:
QUESTION: 95

Centre of pressure compared to c.g. is

Solution:
QUESTION: 96

Flow of water in a pipe about 3 metres in diameter can be measured by

Solution:
QUESTION: 97

The equation of continuity of flow is based on the principle of conservation of

Solution:
QUESTION: 98

The length of divergent portion of ventrumeter in comparison to convergent portion is

Solution:
QUESTION: 99

The intensity of stress which causes unit strain is called

Solution:
QUESTION: 100

True stress- strain curve for materials is plotted between

Solution: