Description

This mock test of Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam.
This contains 20 Multiple Choice Questions for Mechanical Engineering Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2 (mcq) to study with solutions a complete question bank.
The solved questions answers in this Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering
students definitely take this Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2 exercise for a better result in the exam. You can find other Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2 extra questions,
long questions & short questions for Mechanical Engineering on EduRev as well by searching above.

QUESTION: 1

A thin supercritical pressure vessel of 200 mm diameter and 1 mm thickness is subjected to an internal pressure varying from 4 to 8 MPa. Assume that the yield, ultimate, and endurance strength of material are 600, 800 and 400 MPa respectively. The factor of safety as per Goodman’s relation is

Solution:

QUESTION: 2

A forged steel link with uniform diameter of 30 mm at the centre is subjected to an axial force that varies from 40 kN in compression to 160 kN in tension. The tensile (S_{u}), yield (S_{y},) and corrected endurance (S_{e}) strength of the steel material are 600 MPa, 420 MPa and 240 MPa respectively. The factor of safety against fatigue endurance as per Soderberg’s criterion is

Solution:

QUESTION: 3

An aeroplane makes a half circle towards left. The engine runs clockwise when viewed from the rear. Gyroscopic effect on the aeroplane causes the nose to

Solution:

QUESTION: 4

For a disk of moment of inertia I the spin and precession angular velocities are ω and ω_{p} respectively. The magnitude of gyroscopic couple is…………

Solution:

QUESTION: 5

A cylindrical shaft is subjected to an alternating stress of 100 MPa. Fatigue strength to sustain 1000 cycles is 490 MPa. If the corrected endurance strength is 70 MPa, estimated shaft life will be

Solution:

It is a finite life problem. The line AB is the failure line. Where A {3, log_{10} ( 0.9σ_{ult} )} but here it will be A {3, log_{10} ( 490 )} and B{6, log_{10} ( σ_{e} )} here it is B{6, log_{10} ( 70)} Therefore F{ log_{10} N,log_{10}(100)},we have to find N

QUESTION: 6

In designing a shaft for variable loads, the S.N. diagram can be drawn by

Solution:

QUESTION: 7

Match List I with List II and select the correct answer using the codes given below the lists:

Solution:

QUESTION: 8

Fatigue strength of a rod subjected to cyclic axial force is less than that of a rotating beam of the same dimensions subjected to steady lateral force. What is the reason?

Solution:

QUESTION: 9

The design calculations for members subject to fluctuating loads with the same factor of safety yield the most conservative estimates when using

Solution:

QUESTION: 10

Assertion (A): There is a danger of locomotive wheels being lifted above rails at certain speeds.

Reason (R): Lifting of the locomotive wheel above rails at certain speed is due to gyroscopic action.

Solution:

QUESTION: 11

A flywheel has a mass of 300 kg and a radius of gyration of 1m. It is given a spin of 100 r.p.m about its horizontal axis. The whole assembly rotates about a vertical axis at 6 rad/sec. The gyroscopic couple experienced will be

Solution:

QUESTION: 12

In a semi-infinite flat plate shown in the figure, the theoretical stress concentration factor k_{t} for an elliptical hole of major axis 2a and minor axis 2b is given by

Solution:

QUESTION: 13

Match List I (Mechanical Property) with List II (Measured in Terms of) and select the correct answer using the codes given below the lists:

Solution:

QUESTION: 14

A band brake consists of a lever attached to one end of the band. The other end of the band is fixed to the ground. The wheel has a radius of 200 mm and the wrap angle of the band is 270^{o}. The braking force applied to the lever is limited to 100 N, and the coefficient of friction between the band and the wheel is 0.5. No other information is given.

Que: The maximum tension that can be generated in the band during braking is

Solution:

QUESTION: 15

A band brake consists of a lever attached to one end of the band. The other end of the band is fixed to the ground. The wheel has a radius of 200 mm and the wrap angle of the band is 270^{o}. The braking force applied to the lever is limited to 100 N, and the coefficient of friction between the band and the wheel is 0.5. No other information is given.

Que: The maximum wheel torque that can be completely braked is

Solution:

QUESTION: 16

A block-brake shown below has a face width of 300 mm and a mean coefficient of friction of 0.25. For an activating force of 400 N, the braking torque in Nm is

Solution:

QUESTION: 17

A device for lifting or lowering objects suspended from a hook at the end of a retractable chain or cable is called

Solution:

QUESTION: 18

Consider the following statements regarding the differential of an automobile:

1. The speed of the crown wheel will always be the mean of the speeds of the two road wheels.

2. The road wheel speeds are independent of the number of teeth on the planets.

3. The difference between the speeds of the road wheels depends on the number of teeth on the planets.

4. The ratio of speeds of the road wheels depends upon the number of teeth on the gear wheels attached to them and on the crown wheel.

Of these statements

Solution:

QUESTION: 19

In an automobile service station, an automobile is in a lifted up position by means of a hydraulic jack. A person working in the service station gave a tap to one rear wheel and made it rotate by one revolution. The rotation of another rear wheel is

Solution:

When one rear wheel is rotated, other is free.

QUESTION: 20

Rope brake dynamometer uses

Solution:

### Hypersonic vehicle design consideration

Doc | 12 Pages

### Mess, Bar, strips and design consideration

Doc | 10 Pages

### Types of pile load test

Doc | 10 Pages

- Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 2
Test | 20 questions | 60 min

- Fluctuating Load Consideration For Design & Miscellaneous - MCQ Test 1
Test | 20 questions | 60 min

- Test: Design Against Fluctuating Load - 2
Test | 10 questions | 30 min

- Test: Design Against Fluctuating Load - 1
Test | 10 questions | 30 min

- Test: Digital Filters Design Consideration
Test | 10 questions | 10 min