Mechanical Engineering - ME 2014 GATE Paper (Practice Test)


65 Questions MCQ Test Mock Test Series - Mechanical Engineering (ME) for GATE 2020 | Mechanical Engineering - ME 2014 GATE Paper (Practice Test)


Description
This mock test of Mechanical Engineering - ME 2014 GATE Paper (Practice Test) for GATE helps you for every GATE entrance exam. This contains 65 Multiple Choice Questions for GATE Mechanical Engineering - ME 2014 GATE Paper (Practice Test) (mcq) to study with solutions a complete question bank. The solved questions answers in this Mechanical Engineering - ME 2014 GATE Paper (Practice Test) quiz give you a good mix of easy questions and tough questions. GATE students definitely take this Mechanical Engineering - ME 2014 GATE Paper (Practice Test) exercise for a better result in the exam. You can find other Mechanical Engineering - ME 2014 GATE Paper (Practice Test) extra questions, long questions & short questions for GATE on EduRev as well by searching above.
QUESTION: 1

Q. No. 1 – 5 Carry One Mark Each

“India is a country of rich heritage and cultural diversity.” Which one of the following facts best supports the claim made in the above sentence?

Solution:

Diversity is shown in terms of difference language

QUESTION: 2

The value of one U.S. dollar is 65 Indian Rupees today, compared to 60 last year. The Indian Rupee has ____________.

Solution:
QUESTION: 3

'Advice' is ________________.

Solution:
*Answer can only contain numeric values
QUESTION: 4

The next term in the series 81, 54, 36, 24 … is ________

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 5

In which of the following options will the expression P < M be definitely true?

Solution:
QUESTION: 6

Q. No. 6 – 10 Carry Two Marks Each

Q. Find the next term in the sequence: 7G, 11K, 13M, ___

Solution:
QUESTION: 7

The multi-level hierarchical pie chart shows the population of animals in a reserve forest. The correct conclusions from this information are:

(i) Butterflies are birds
(ii) There are more tigers in this forest than red ants
(iii) All reptiles in this forest are either snakes or crocodiles
(iv) Elephants are the largest mammals in this forest

Solution:

It is not mentioned that elephant is the largest animal

*Answer can only contain numeric values
QUESTION: 8

A man can row at 8 km per hour in still water. If it takes him thrice as long to row upstream, as to row downstream, then find the stream velocity in km per hour.

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 9

A firm producing air purifiers sold 200 units in 2012. The following pie chart presents the share of raw material, labour, energy, plant & machinery, and transportation costs in the total manufacturing cost of the firm in 2012. The expenditure on labour in 2012 is Rs. 4,50,000. In 2013, the raw material expenses increased by 30% and all other expenses increased by 20%. If the company registered a profit of Rs. 10 lakhs in 2012, at what price (in Rs.) was each air purifier sold?

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 10

A batch of one hundred bulbs is inspected by testing four randomly chosen bulbs. The batch
is rejected if even one of the bulbs is defective. A batch typically has five defective bulbs.
The probability that the current batch is accepted is _________

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 11

Q. No. 11 – 35 Carry One Mark Each
1. Consider a 3 × 3 real symmetric matrix S such that two of its eigen values are a = 0 , b = 0 with respective eigen vectors  . If a = b then x1y1 + x2y2 + x2y2 equals

Solution:

We know that the Eigen vectors  corresponding to distinct Eigen values of real symmetric matrix are orthogonal.

QUESTION: 12

If a function is continuous at a point,

Solution:

QUESTION: 13

Divergence of the vector field at (1, -1, 1) is

Solution:

*Answer can only contain numeric values
QUESTION: 14

A group consists of equal number of men and women. Of this group 20% of the men and 50% of the women are unemployed. If a person is selected at random from this group, the probability of the selected person being employed is _______

(Important - Enter only the numerical value in the answer)


Solution:

*Answer can only contain numeric values
QUESTION: 15

The definite integral  is evaluated using Trapezoidal rule with a step size of 1. The correct answer is ________

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 16

A rotating steel shaft is supported at the ends. It is subjected to a point load at the centre. The maximum bending stress developed is 100 MPa. If the yield, ultimate and corrected endurance strength of the shaft material is 300 MPa, 500 MPa and 200 MPa, respectively, then the factor of safety for the shaft is _______

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 17

Two solid circular shafts of radii R1 and R2 are subjected to same torque. The maximum shear stresses developed in the two shafts are τ1 and τ2 . If R1 / R2=2, then τ2 / τ1 is _______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 18

Consider a single degree-of-freedom system with viscous damping excited by a harmonic force. At resonance, the phase angle (in degree) of the displacement with respect to the exciting force is

Solution:
QUESTION: 19

A mass 1 m of 100 kg travelling with a uniform velocity of 5 m/s along a line collides with a stationary mass m2 of 1000 kg. After the collision, both the masses travel together with the same velocity. The coefficient of restitution is

Solution:

QUESTION: 20

Which one of following is NOT correct?

Solution:
QUESTION: 21

Gear 2 rotates at 1200 rpm in counter clockwise direction and engages with Gear 3. Gear 3 and Gear 4 are mounted on the same shaft. Gear 5 engages with Gear 4. The numbers of teeth on Gears 2, 3, 4 and 5 are 20, 40, 15 and 30, respectively. The angular speed of Gear 5 is

Solution:

QUESTION: 22

Consider a long cylindrical tube of inner and outer radii, ri and ro , respectively, length, L and thermal conductivity, k. Its inner and outer surfaces are maintained at Ti and T0, respectively ( Ti > TO ). Assuming one-dimensional steady state heat conduction in the radial direction, the thermal resistance in the wall of the tube is

Solution:

QUESTION: 23

Which one of the following pairs of equations describes an irreversible heat engine?

Solution:

QUESTION: 24

Consider the turbulent flow of a fluid through a circular pipe of diameter, D. Identify the correct pair of statements.
I. The fluid is well-mixed
II. The fluid is unmixed
III. ReD < 2300
IV. ReD > 2300

Solution:

ReD > 2300 means it is a turbulent flow. In turbulent flow, the fluid is well mixed. The fluid is unmixed, for a very-low Reynolds number laminar flow.

QUESTION: 25

For a gas turbine power plant, identify the correct pair of statements. 

P. Smaller in size compared to steam power plant for same power output

Q. Starts quickly compared to steam power plant

R. Works on the principle of Rankine cycle

S. Good compatibility with solid fuel

Solution:

Steam power plants are bulky due to presence of boiler and condenser. Gas turbines are compact, as compressors and turbines are coupled on a common shaft. In steam power plants, boiler takes lot of time to get started, as compared to Gas Turbines.

*Answer can only contain numeric values
QUESTION: 26

A source at a temperature of 500 K provides 1000 kJ of heat. The temperature of environment is 27OC. The maximum useful work (in kJ) that can be obtained from the heat source is_______

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 27

A sample of moist air at a total pressure of 85 KPa has a dry bulb temperature of 30°C (saturation vapour pressure of water = 4.24 KPa). If the air sample has a relative humidity of 65%, the absolute humidity (in gram) of water vapour per kg of dry air is _______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 28

The process utilizing mainly thermal energy for removing material is

Solution:
*Answer can only contain numeric values
QUESTION: 29

The actual sales of a product in different months of a particular year are given below:

The forecast of the sales, using the 4-month moving average method, for the month of February is _______

(Important - Enter only the numerical value in the answer) 


Solution:

Number of periods = 4, then the past 4 months average sales is fore cast for next 4 months.

*Answer can only contain numeric values
QUESTION: 30

A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel rod. The feed is 0.2 mm/rev and the depth of cut is 0.5 mm. The tool has a side cutting edge angle of 60°. The uncut chip thickness (in mm) is _______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 31

A minimal spanning tree in network flow models involves

Solution:

A path forms a loop or cycle if it connects a node itself. A spanning tree links all the nodes of network with no loops allowed.

QUESTION: 32

A path forms a loop or cycle if it connects a node itself. A spanning tree links all the nodes of network with no loops allowed.

Solution:
QUESTION: 33

Cutting tool is much harder than the workpiece. Yet the tool wears out during the tool-work interaction, because

Solution:
QUESTION: 34

The stress-strain curve for mild steel is shown in the figure given below. Choose the correct option referring to both figure and table.

Solution:
QUESTION: 35

The hot tearing in a metal casting is due to

Solution:
QUESTION: 36

Q. No. 36 – 65 Carry Two Marks Each

Q. An analytic function of a complex variable z = x + iy is expressed as f(z) = w(x, y) + iv(x, y), where. If u(x, y) = x2 – y2, then expression for v(x, y) in terms of x, y and a general constant c would be

Solution:

QUESTION: 37

Consider two solutions x(t) = x1t and x(t) and x(t) = x2(t) of the differential equation

Solution:

QUESTION: 38

A machine produces 0, 1 or 2 defective pieces in a day with associated probability of 1/6, 2/3 and 1/6, respectively. The mean value and the variance of the number of defective pieces produced by the machine in a day, respectively, are

Solution:

*Answer can only contain numeric values
QUESTION: 39

The real root of the equation 5x − 2cosx −1 = 0 (up to two decimal accuracy) is _______

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 40

A drum brake is shown in the figure. The drum is rotating in anticlockwise direction. The coefficient of friction between drum and shoe is 0.2. The dimensions shown in the figure are in mm. The braking torque (in N.m) for the brake shoe is _______

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 41

A body of mass (M) 10 kg is initially stationary on a 45° inclined plane as shown in figure. The coefficient of dynamic friction between the body and the plane is 0.5. The body slides down the plane and attains a velocity of 20 m/s. The distance travelled (in meter) by the body along the plane is _______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 42

Consider a simply supported beam of length, 50h, with a rectangular cross-section of depth, h, and width, 2h. The beam carries a vertical point load, P, at its mid-point. The ratio of the maximum shear stress to the maximum bending stress in the beam is

Solution:

*Answer can only contain numeric values
QUESTION: 43

The damping ratio of a single degree of freedom spring-mass-damper system with mass of 1 kg, stiffness 100 N/m and viscous damping coefficient of 25 N.s/m is _______


Solution:

QUESTION: 44

An annular disc has a mass m, inner radius R and outer radius 2R. The disc rolls on a flat surface without slipping. If the velocity of the centre of mass is v, the kinetic energy of the disc is

Solution:

QUESTION: 45

A force P is applied at a distance x from the end of the beam as shown in the figure. What would be the value of x so that the displacement at ‘A’ is equal to zero?

Solution:

QUESTION: 46

Consider a rotating disk cam and a translating roller follower with zero offset. Which one of the following pitch curves, parameterized by t, lying in the interval 0 to 2π, is associated with the maximum translation of the follower during one full rotation of the cam rotating about the center at (x, y) = (0, 0) ?

Solution:

*Answer can only contain numeric values
QUESTION: 47

A four-wheel vehicle of mass 1000 kg moves uniformly in a straight line with the wheels revolving at 10 rad/s. The wheels are identical, each with a radius of 0.2 m. Then a constant braking torque is applied to all the wheels and the vehicle experiences a uniform deceleration. For the vehicle to stop in 10 s, the braking torque (in N.m) on each wheel is _______

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 48

A slider-crank mechanism with crank radius 60 mm and connecting rod length 240 mm is shown in figure. The crank is rotating with a uniform angular speed of 10 rad/s, counter clockwise. For the given configuration, the speed (in m/s) of the slider is _______

(Important - Enter only the numerical value in the answer) 


Solution:
*Answer can only contain numeric values
QUESTION: 49

Consider an objective function Z(x1 ,x2) = 3x1 + 9x2 and the constraints
x1 + x2 < 8,

x1 + 2x2 < 4,

x1 >  x2 > 0,

The maximum value of the objective function is _______


Solution:

Roots are (12,-4) and (12,-2)
Maximum value of objective function = 3(12)+9(-2) = 18.

*Answer can only contain numeric values
QUESTION: 50

A mass-spring-dashpot system with mass m = 10 kg, spring constant k = 6250 N/m is excited by a harmonic excitation of 10 cos(25t) N. At the steady state, the vibration amplitude of the mass is 40 mm. The damping coefficient (c, in N.s/m) of the dashpot is _______ 


Solution:

QUESTION: 51

A certain amount of an ideal gas is initially at a pressure P1 and temperature T1. First, it undergoes a constant pressure process 1-2 such that T2 = 3T1/4. Then, it undergoes a constant volume process 2-3 such that T3 = T1/2. The ratio of the final volume to the initial volume of the ideal gas is

Solution:

*Answer can only contain numeric values
QUESTION: 52

An amount of 100 kW of heat is transferred through a wall in steady state. One side of the wall is maintained at 127OC and the other side at 27OC. The entropy generated (in W/K) due to the heat transfer through the wall is _______

(Important - Enter only the numerical value in the answer) 


Solution:

 

QUESTION: 53

A siphon is used to drain water from a large tank as shown in the figure below. Assume that the level of water is maintained constant. Ignore frictional effect due to viscosity and losses at entry and exit. At the exit of the siphon, the velocity of water is

Solution:

*Answer can only contain numeric values
QUESTION: 54

Heat transfer through a composite wall is shown in figure. Both the sections of the wall have equal thickness (l). The conductivity of one section is k and that of the other is 2k. The left face of the wall is at 600 K and the right face is at 300 K. The interface temperature Ti (in K) of the composite wall is _______


Solution:

*Answer can only contain numeric values
QUESTION: 55

A fluid of dynamic viscosity 2 × 10-5 kg/m.s and density 1 kg/m3 flows with an average velocity of 1 m/s through a long duct of rectangular (25 mm × 15 mm) cross-section. Assuming laminar flow, the pressure drop (in Pa) in the fully developed region per meter length of the duct is _______

(Important - Enter only the numerical value in the answer) 


Solution:

Given,

*Answer can only contain numeric values
QUESTION: 56

At the inlet of an axial impulse turbine rotor, the blade linear speed is 25 m/s, the magnitude of absolute velocity is 100 m/s and the angle between them is 25°. The relative velocity and the axial component of velocity remain the same between the inlet and outlet of the blades. The blade inlet and outlet velocity triangles are shown in the figure. Assuming no losses, the specific work (in J/kg) is _______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 57

A solid sphere of radius r1 = 20 mm is placed concentrically inside a hollow sphere of radius r2 = 30 mm as shown in the figure. 

The view factor F21 for radiation heat transfer is

Solution:

*Answer can only contain numeric values
QUESTION: 58

A double-pipe counter-flow heat exchanger transfers heat between two water streams. Tube side water at 19 liter/s is heated from 10OC to 38OC. Shell side water at 25 liter/s is entering at 46OC. Assume constant properties of water, density is 1000 kg/m3 and specific heat is 4186 J/kg K. The LMTD (in OC) is ________

(Important - Enter only the numerical value in the answer) 


Solution:

*Answer can only contain numeric values
QUESTION: 59

A diesel engine has a compression ratio of 17 and cut-off take place at 10% of the stroke. Assuming ratio of specific heats (g ) as 1.4, the air-standard efficiency (in percent) is_______

(Important - Enter only the numerical value in the answer) 


Solution:

QUESTION: 60

Consider the given project network, where numbers along various activities represent the normal time. The free float on activity 4-6 and the project duration, respectively, are

Solution:

QUESTION: 61

A manufacturer can produce 12000 bearings per day. The manufacturer received an order of 8000 bearings per day from a customer. The cost of holding a bearing in stock is Rs.0.20 per month. Setup cost per production run is Rs.500. Assuming 300 working days in a year, the frequency of production run should be

Solution:
QUESTION: 62

A cylindrical blind riser with diameter d and height h, is placed on the top of the mold cavity of a closed type sand mold as shown in the figure. If the riser is of constant volume, then the rate of solidification in the riser is the least when the ratio h/d is

Solution:

 

*Answer can only contain numeric values
QUESTION: 63

The diameter of a recessed ring was measured by using two spherical balls of diameter d2 =60 mm and d= 40 mm as shown in the figure.

The distance H2 = 35.55 mm and H1 = 20.55 mm. The diameter (D, in mm) of the ring gauge is _______


Solution:

QUESTION: 64

Which pair of following statements is correct for orthogonal cutting using a single-point cutting tool?

P. Reduction in friction angle increases cutting force
Q. Reduction in friction angle decreases cutting force
R. Reduction in friction angle increases chip thickness
S. Reduction in friction angle decreases chip thickness

Solution:
*Answer can only contain numeric values
QUESTION: 65

For spot welding of two steel sheets (base metal) each of 3 mm thickness, welding current of 10000 A is applied for 0.2s. The heat dissipated to the base metal is 1000 J. Assuming that the heat required for melting 1 mm3 volume of steel is 20 J and interfacial contact resistance between sheets is 0.000 2? , the volume (in mm3) of weld nugget is _______

(Important - Enter only the numerical value in the answer) 


Solution: