Description

This mock test of Flow Over Notches And Weirs for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam.
This contains 7 Multiple Choice Questions for Civil Engineering (CE) Flow Over Notches And Weirs (mcq) to study with solutions a complete question bank.
The solved questions answers in this Flow Over Notches And Weirs quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE)
students definitely take this Flow Over Notches And Weirs exercise for a better result in the exam. You can find other Flow Over Notches And Weirs extra questions,
long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.

QUESTION: 1

Consider the following measuring structures:

1. Submerged broad-crested weir

2. Free broad-crested weir

3. Free sharp-crested weir

4. Free ogee spillway

The correct sequence of the increasing order of the discharge coefficient of these structures is

Solution:

For ogee spillway, C_{d1} = 1.19 C_{ds}

Cds is the discharge coefficient for sharp - crested weir. So 4 will come after 3.

The classification of weir is:

Further submerged weirs have lesser coefficient of discharge compared to free weirs. So, 2 will come after 1.

QUESTION: 2

Match List-I with List-ll and,select the correct answer using the codes given below the lists:

List-I

A. Rehbock formula

B. Francis formula

C. A special trapezoidal weir

D. Linear proportional weir

List-lI

1. Sutroweir

2. Rectangular suppressed weir

3. Rectangular side-contracted weir

4. Cippolietti weir

Solution:

(i) Rehbock’s formula is an empirical formula for calculating discharge in rectangular suppressed weir. It is given by,

Where L is the length of weir, H is head in meters and Z is the crest height in meters,

(ii) Francis’ formula is one of the commonly used empirical formula for computing the discharge over sharp or narrow crested weirs with or without end contraction. Francis proposed the following formulae for the discharge over rectangular weir.

(a) When the velocity of approach is not considered,

(b) With the velocity of approach is taken into account,

water surface above the crest of weir, and n is the number of end contractions.

QUESTION: 3

The head over a V notch at the end of a channel is 75 cm. If an error of 0.15 cm is possible in the measurement of head, the percentage error. in computing the discharge will be

Solution:

Percentage error discharge over a

Similarly percentage error in discharge in a rectangular weir

QUESTION: 4

A hemispherical tank of radius R has an orifice of cross - sectional area ‘a’ at its bottom and is full of liquid. The time required to empty the tank completely is

Solution:

QUESTION: 5

A triangular notch is a more accurate measuring device than a rectangular notch

Solution:

QUESTION: 6

The head over a 90° V notch weir is increased from 0.15 m to 0.30 m. The ratio of new discharge to the original discharge will be

Solution:

QUESTION: 7

The discharge through a Cipolletti weir is given by where symbols have their, usual meanings.

Solution:

### Chapter 11 Flow Over Bodies: Drag and Lift Chapter 11 FLOW OVER BODIES: DRAG AND LIFT

Doc | 21 Pages

### Chapter 11 Flow Over Bodies: Drag and Lift Lift

Doc | 31 Pages

### Flow meter flow devices

Doc | 4 Pages

- Flow Over Notches & Weirs
Test | 10 questions | 30 min

- Flow Over Notches And Weirs
Test | 7 questions | 20 min

- Kinematics Of Flow And Ideal Flow - 3
Test | 15 questions | 45 min

- Test: Asynchronous Flow Control
Test | 10 questions | 25 min

- Turbulent Flow - 1
Test | 10 questions | 30 min