Description

This mock test of Transportation Engineering - 2 for Civil Engineering (CE) helps you for every Civil Engineering (CE) entrance exam.
This contains 15 Multiple Choice Questions for Civil Engineering (CE) Transportation Engineering - 2 (mcq) to study with solutions a complete question bank.
The solved questions answers in this Transportation Engineering - 2 quiz give you a good mix of easy questions and tough questions. Civil Engineering (CE)
students definitely take this Transportation Engineering - 2 exercise for a better result in the exam. You can find other Transportation Engineering - 2 extra questions,
long questions & short questions for Civil Engineering (CE) on EduRev as well by searching above.

QUESTION: 1

The radius of a horizontal circular curve on a highway is 120 m. The design speed is 60 km/hour, and the design coefficient of lateral friction between the tyre and the road surface is 0.15. The estimated value of superelevation required (if full lateral friction is assumed to develop), and the value of the coefficient of friction needed (if no superelevation is provided) will, respectively, be

Solution:

Given ⇒ R = 120 m

f = 0.15

If full lateral friction is assumed to develop, then

If, e = 0

= 0.24

QUESTION: 2

The critical flow ratios for a three-phase signal are found to be 0.30, 0.25, and 0.25. The total time lost in the cycle is 10 s. Pedestrian crossings at this junction are not significant. The respective Green times (expressed in seconds and rounded off to the nearest integer) for the three phases are

Solution:

Y = y_{1} + y_{2} + y_{3}

= 0.30 + 0.25 + 0.25= 0.80

Now Total lost time

L = 10 sec (given)

∴ Optimum cycle time

Now green times are calculated by,

*Answer can only contain numeric values

QUESTION: 3

A motorist traveling at 100 km/h on a highway needs to take the next exit, which has a speed limit of 50 km/h. The section of the roadway before the ramp entry has a downgrade of 3% and the coefficient of friction ( f ) is 0.35. In order to enter the ramp at the maximum allowable speed limit, the braking distance (expressed in m) from the exit ramp is _________.

Solution:

Total energy lost between point (1) and (2)

= Work done by frictional force

= 0.35 × 9.81 × s

289.815 = 3.1392 s

**s = 92.32 m**

*Answer can only contain numeric values

QUESTION: 4

The relation between speed *u *(in km/h) and density *k *(number of vehicles / km) for a traffic stream on a road is *u *= 70 – 0.7*k*. The capacity on this road is _______________ vph (vehicles/hour).

Solution:

Traffic volume,

q = uk

q = (70 – 0.7 k) k= 70k – 0.7 k2

Maximum possible volume is capacity of road.

For maximum volume

⇒ 70 – 1.4 k = 0

⇒ k = 50 Veh /km

Hence, capacity

C = (70 – 0.7 × 50) × 50

**C = 1750 Veh/hr**

QUESTION: 5

During a forensic investigation of pavement failure, an engineer reconstructed the graphs P, Q, R and S, using partial and damaged old reports.

Theoretically plausible correct graphs according to the 'Marshall mixture design output' are

Solution:

The graph between VFB and Bitumen content is

QUESTION: 6

A superspeedway in New Delhi has among the highest super-elevation rates of any track on the Indian Grand Prix circuit. The track requires drivers to negotiate turns with a radius of 335 m and 33° banking. Given this information, the coefficient of side friction required in order to allow a vehicle to travel at 320 km/h along the curve is:

Solution:

R = 335 m

V = 320 km/hr

= 1.761

*Answer can only contain numeric values

QUESTION: 7

The penetration value of a bitumen sample tested at 25°C is 80. When this sample is heated to 60°C and tested again, the needle of the penetration test apparatus penetrates the bitumen sample by *d* mm. The value of *d *CANNOT be less than _______________ mm.

Solution:

The penetration value is 1/10th of the bitumen sample grade.

The penetration value of 80 means the needle of the penetration test apparatus penetrates the bitumen sample by 80/10= 8 mm

QUESTION: 8

In the context of the IRC 58-2011 guidelines for rigid pavement design, consider the following pair

of statements.

I: Radius of relative stiffness is directly related to the modulus of elasticity of concrete and inversely

related to Poisson's ratio.

II: Radius of relative stiffness is directly related to the thickness of slab and modulus of subgrade

reaction.

Which one of the following combinations is correct?

Solution:

Radius of relative stiffness

As μ increases then 1 – μ^{2} decreases.

∴ Relative stiffness also increases

∴ Statements 1 is false

Modulus of subgrade reaction is

Hence, Statement 2 is false.

*Answer can only contain numeric values

QUESTION: 9

While traveling along and against the traffic stream, a moving observer measured the relative flows as 50 vehicles/hr and 200 vehicles/hr, respectively. The average speeds of the moving observer while traveling along and against the stream are 20 km/hr and 30 km/hr, respectively. The density of the traffic stream (expressed in vehicles/km) is

Solution:

Solution: q = traffic flow

k = traffic density

V_{w} = velocity of test vehicle along the stream

V_{a} = velocity of test vehicle against the stream

⇒ q – kV_{w} = 50

**⇒**** q – k × 20 = 50**

q + kVa = 200

**⇒**** q + k × 30 = 200**

Solving equation (i) and (ii), we get

k = 3 Veh/km

*Answer can only contain numeric values

QUESTION: 10

The radii of the relative stiffness of the rigid pavement P and Q are denoted by IP and IQ respectively. The geometric and material properties of the concrete slab and underlying soil are given below.

The ratio (up to one decimal place) of I_{P} / I_{Q} is _____.

Solution:

QUESTION: 11

In Marshall method of mix design, the coarse aggregate, fine aggregate, fines and bitumen having respective values of specific gravity 2.60, 2.70, 2.65 and 1.01, are mixed in the relative proportions (% by weight) of 55.0, 35.8, 3.7 and 5.5 respectively. The theoretical specific gravity of the mix and the effective specific gravity of the aggregates in the mix respectively are:

Solution:

Theoretical specific gravity

Effective specific gravity of aggregates (coarse + fine) is given by

QUESTION: 12

Two cars P and Q are moving in a racing track continuously for two hours. Assume that no other vehicles are using the track during this time. The expressions relating the distance traveled d (in km) and time t (an hour) for both the vehicles are given as

P (d) = 60t

Q (d) = 60t^{2}

Within the first one hour, the maximum space headway would be

Solution:

P: d = 60t

Q: d = 60t^{2}

Space Headway (S) = 60t^{2} – 60t

For space headway to be max,

120t – 60 = 0

⇒ 60(2t – 1) = 0

⇒ t = ½ hr

Maximum space Headway

= 60 × ½ - 60 × (½)^{2}

= 60 × ½ - 60 × ¼

= 30 – 15 = **15 km**

*Answer can only contain numeric values

QUESTION: 13

A sign is required to be put up asking drivers to slow down to 30 km/h before entering Zone Y (see figure). On this road, vehicles require 174 m to slow down to 30 km/h (the distance of 174 m includes the distance traveled during the perception-reaction time of drivers). The sign can be read by 6/6 vision drivers from a distance of 48 m. The sign is placed at a distance of x m from the start of Zone Y so that even a 6/9 vision driver can slow down to 30 km/h before entering the zone. The minimum value of x is _______________ m.

Solution:

For a driver having 6/6 vision can see the board from distance 48 m.

For a driver having 6/9 vision can see the board from a of distance

Vehicle requires 174 m to slow down to 30 km/hr.

So minimum distance of X from the start of Y zone

= 174 – 32

= 142 m

Hence, the minimum value of X = 142 m

*Answer can only contain numeric values

QUESTION: 14

The acceleration-time relationship for a vehicle subjected to non-uniform acceleration is

where *v *is the speed in m/s, *t *is the time in s, α and β are parameters, and *v0 *is the initial speed in m/s. If the accelerating behavior of a vehicle, whose driver intends to overtake a slow-moving vehicle ahead, is described as,

Considering at t = 3 s, the distance (in m) traveled by the vehicle in 35 s is ___.

Solution:

∴ In (2 – 0.05 × v) = (t – 8.247) – (– 0.05)

⇒ 2 – 0.05 × v = 1.51 e^{-0.05t
}

∴ at t = 0, s = 0 ⇒ c’ = – 604.15

Hence, **s = 40t + 604.15 e ^{-0.05t} – 604.15**

at t = 35 sec

s = 40 × 35 + 604.15 e^{-0.05 × 35} – 604.15

s = 900.84 m

QUESTION: 15

The queue length (in a number of vehicles) versus time (in seconds) plot for an approach to a signalized intersection with the cycle length of 96 seconds is shown in the figure (not drawn to scale).

At time = t = 0, the light has just turned red. The effective green time is 36 seconds, during which vehicles discharge at the saturation flow rate, s (in vph). Vehicles arrive at a uniform rate, v (in vph), throughout the cycle. Which one of the following statements is TRUE?

Solution:

Vehicle arrived upto 60 sec (Red time) = 10

**V = 600 V/h**

Between = 60 second to 90 second total vehicle departed

= Vehicle arrived upto 60 second + Vehicle arriving between 60 sec to 90 sec

= 10 + 5

= 15

So, departure rate = Saturation flow

**S = 1800 v/h**

Average delay time is given by

C = 96 seconds

g = 96 – 60 = 36 seconds

V = 600 Vph

S = 1800 Vph

t_{d} = 28.125 seconds

### Transportation Engineering paper2

Doc | 1 Page

### Transportation (Part - 2)

Video | 18:50 min

### DATA-COLLECTION Transportation Engineering

Doc | 7 Pages

### Transportation-Systems-Engineering-Advanced-ITS

Doc | 5 Pages

- Transportation Engineering - 2
Test | 15 questions | 45 min

- Transportation Engineering - 2
Test | 20 questions | 60 min

- Transportation Engineering - 1
Test | 10 questions | 30 min

- Transportation Engineering - 1
Test | 15 questions | 45 min

- Transportation Engineering - 1
Test | 20 questions | 12 min