GATE  >  GATE Electrical Engineering (EE) 2023 Mock Test Series  >  Test: Electrical Machines- 1 Download as PDF

Test: Electrical Machines- 1


Test Description

10 Questions MCQ Test GATE Electrical Engineering (EE) 2023 Mock Test Series | Test: Electrical Machines- 1

Test: Electrical Machines- 1 for GATE 2022 is part of GATE Electrical Engineering (EE) 2023 Mock Test Series preparation. The Test: Electrical Machines- 1 questions and answers have been prepared according to the GATE exam syllabus.The Test: Electrical Machines- 1 MCQs are made for GATE 2022 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Test: Electrical Machines- 1 below.
Solutions of Test: Electrical Machines- 1 questions in English are available as part of our GATE Electrical Engineering (EE) 2023 Mock Test Series for GATE & Test: Electrical Machines- 1 solutions in Hindi for GATE Electrical Engineering (EE) 2023 Mock Test Series course. Download more important topics, notes, lectures and mock test series for GATE Exam by signing up for free. Attempt Test: Electrical Machines- 1 | 10 questions in 30 minutes | Mock test for GATE preparation | Free important questions MCQ to study GATE Electrical Engineering (EE) 2023 Mock Test Series for GATE Exam | Download free PDF with solutions
1 Crore+ students have signed up on EduRev. Have you?
Test: Electrical Machines- 1 - Question 1

In an electromechanical energy conversion device, the developed torque depends upon

Test: Electrical Machines- 1 - Question 2

Consider the following statements:

The use of interpoles in dc machines is to counteract the
1. reactance voltage
2. demagnetizing effect of armature mmf in the commutating zone
3. cross-magnetizing effect of armature mmf in the commutating zone

Which of these statement(s) is/are correct?

Detailed Solution for Test: Electrical Machines- 1 - Question 2

In practice, the interpoles of appropriate polarity are strengthened so that in interpolar zone, the armature cross flux is neutralized and in addition some flux is produced there. This additional flux in the interpolar zone induces rotational emf in the commutated coil in such a direction as to oppose the reactance voltage. So, the resultant emf in the commutated coil would be zero and therefore zero current in that coil would amount to sparkless commutation. This is the reason why interpoles are designed to provide more mmf than the armature mmf in the commutating zone. In practice, the interpole mmf may be 1.2 to 1.3 times the armature mmf per pole.

Test: Electrical Machines- 1 - Question 3

In an armature, if m is the number of slots per pole per phase and γ is the slot pitch angle, then the breadth or the distribution factor for the armature winding is

Test: Electrical Machines- 1 - Question 4

The current drawn by a 220V dc motor of armature resistance 0.5 Ω and back emf 200V is

Detailed Solution for Test: Electrical Machines- 1 - Question 4

Ea = V – Ia Ra
Ea = 200 = 220 – Ia × 0.5 ⇒ Ia = 40 A 

Test: Electrical Machines- 1 - Question 5

A dc shunt generator when driven without connecting field winding shows an open circuit terminal voltage of 12V. When field winding is connected and excited, the terminal voltage drops to zero because

Detailed Solution for Test: Electrical Machines- 1 - Question 5

If shunt field resistance is more than the critical field resistance, there will be no voltage build up beyond residual voltage but voltage would not be zero.

Test: Electrical Machines- 1 - Question 6

Match List-I (dc motors) with List-II (Characteristics) labeled 1, 2, 3 and 4) and select the correct answer:

Test: Electrical Machines- 1 - Question 7

An induction motor when started on load does not accelerate up to full speed but runs at 1/7th of the rated speed. The motor is said to be

Detailed Solution for Test: Electrical Machines- 1 - Question 7

Refer, harmonic asynchronous (induction) torques. Running stably at low speed (around 1/7th normal motor speed) is known as Crawling.

Test: Electrical Machines- 1 - Question 8

The rotor power output of 3-phase induction motor is 15 kW. The rotor copper losses at a slip of 4% will be

Detailed Solution for Test: Electrical Machines- 1 - Question 8

Test: Electrical Machines- 1 - Question 9

Skewing of the rotor in a three-phase squirrel-cage induction motor reduces

Detailed Solution for Test: Electrical Machines- 1 - Question 9

If rotor slots are skewed by 2 harmonic polepitches, then effect of slot harmonics (Parasitic torques) can be eliminated.
Since the skewed rotor slot is not parallel to stator slot in an induction motor, there is more leakage reactance. As a result, induction motor has lower starting and maximum torques.
With skewed rotor bars, the revolving flux, in effect, encounters an air gap of uniform reluctance and this results in a uniform torque and quieter operation.

Test: Electrical Machines- 1 - Question 10

In a shaded-pole induction motor, the rotor runs from the

Use Code STAYHOME200 and get INR 200 additional OFF
Use Coupon Code
Information about Test: Electrical Machines- 1 Page
In this test you can find the Exam questions for Test: Electrical Machines- 1 solved & explained in the simplest way possible. Besides giving Questions and answers for Test: Electrical Machines- 1, EduRev gives you an ample number of Online tests for practice