Chapter : Bipolar Junction Transistor (BJT), Electronics and Communication Engineering - Electronics and Communication Engineering (ECE) PDF Download

Bipolar Junction Transistor (BJT)

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Introduction

•The basic of electronic system nowadays is semiconductor device.
•The famous and commonly use of this device is BJTs (Bipolar Junction Transistors).
• It can be use as amplifier and logic switches.
• BJT consists of three terminal:
 collector : C
 base : B
emitter : E
• Two types of BJT : pnp and npn

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Transistor Construction

•3 layer semiconductor device consisting:
•2 n- and 1 p-type layers of material  npn transistor
•2 p- and 1 n-type layers of material pnp transistor
•The term bipolar reflects the fact that holes and electrons participate in the injection process into the oppositely polarized material
•A single pn junction has two different types of bias:
• forward bias
• reverse bias
• Thus, a two-pn-junction device has four types of bias.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Position of the terminals and symbol of BJT.

• Base is located at the middle and more thin from the level of collector and emitter
• The emitter and collector terminals are made of the same type of semiconductor material, while the base of the other type of material

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Transistor currents

-The arrow is always drawn on the emitter
-The arrow always point toward the n-type
-The arrow indicates the direction of the emitter current: pnp:E B npn: B E
IC=the collector current
IB= the base current
IE= the emitter current

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•By imaging the analogy of diode, transistor can be construct like two diodes that connetecd together.
•It can be conclude that the work of transistor is base on work of diode.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Transistor Operation

•The basic operation will be described using the pnp transistor. The operation of the pnp transistor is exactly the same if the roles played by the electron and hole are interchanged.
•One p-n junction of a transistor is reverse-biased, whereas the other is forward-biased.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•Both biasing potentials have been applied to a pnp transistor and resulting majority and minority carrier flows indicated.
•Majority carriers (+) will diffuse across the forward-biased p-n junction into the n-type material.
•A very small number of carriers (+) will through n-type material to the base terminal. Resulting IB is typically in order of microamperes.
•The large number of majority carriers will diffuse across the reverse-biased junction into the p-type material connected to the collector terminal.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•Majority carriers can cross the reverse-biased junction because the injected majority carriers will appear as minority carriers in the n-type material.
•Applying KCL to the transistor :
IE = IC + IB
•The comprises of two components – the majority and minority carriers
IC = ICmajority + ICOminority
•ICO – IC current with emitter terminal open and is called leakage current.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Common-Base Configuration

•Common-base terminology is derived from the fact that the :
- base is common to both input and output of the configuration.
- base is usually the terminal closest to or at ground potential.
•All current directions will refer to conventional (hole) flow and the arrows in all electronic symbols have a direction defined by this convention.
•Note that the applied biasing (voltage sources) are such as to establish current in the direction indicated for each branch.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•To describe the behavior of common-base amplifiers requires two set of characteristics:
-Input or driving point characteristics.
-Output or collector characteristics
•The output characteristics has 3 basic regions:
-Active region –defined by the biasing arrangements
-Cutoff region – region where the collector current is 0A
-Saturation region- region of the characteristics to the left of VCB = 0V

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•The curves (output characteristics) clearly indicate that a first approximation to the relationship between IE and IC in the active region is given by
IC ≈IE
•Once a transistor is in the ‘on’ state, the base-emitter voltage will be assumed to be
VBE = 0.7V

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

• In the dc mode the level of IC and IE due to the
majority carriers are related by a quantity called alpha
=
IC = IE + ICBO
• It can then be summarize to IC = IE (ignore ICBO due to small value)
• For ac situations where the point of operation moves on the characteristics curve, an ac alpha defined by
• Alpha a common base current gain factor that shows the efficiency by calculating the current percent from current flow from emitter to collector.The value of 
is typical from 0.9 ~ 0.998.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Biasing

•Proper biasing CB configuration in active region by approximation IC  IE (IB  0 uA)

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Transistor as an amplifier

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Simulation of transistor as an amplifier

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Common-Emitter Configuration

•It is called common-emitter configuration since :
- emitter is common or reference to both input and output terminals.
- emitter is usually the terminal closest to or at ground
potential.
•Almost amplifier design is using connection of CE due to the high gain for current and voltage.
•Two set of characteristics are necessary to describe the behavior for CE ;input (base terminal) and output (collector terminal) parameters.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Proper Biasing common-emitter configuration in active region

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•IB is microamperes compared to miliamperes of IC.
• IB will flow when VBE > 0.7V
for silicon and 0.3V for germanium
•Before this value IB is very small and no IB.
• Base-emitter junction is forward bias
• Increasing VCE will reduce IB for different values.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•For small VCE (VCE < VCESAT, IC increase linearly with increasing of VCE
• VCE > VCESAT IC not totally depends on VCE  constant IC
• IB(uA) is very small compare to IC (mA). Small increase in IB cause big increase in IC
• IB=0 A  ICEO occur.
•Noticing the value when IC=0A. There is still some value of current flows.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Beta (β) or amplification factor

•The ratio of dc collector current (IC) to the dc base current (IB) is dc beta (dc ) which is dc current gain where IC and IB are determined at a particular operating point, Q-point (quiescent point).
• It’s define by the following equation:
30 < dc < 300  2N3904
•On data sheet, dc=hFE with h is derived from ac hybrid equivalent cct. FE are derived from forward-current amplification and common-emitter configuration respectively.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

•For ac conditions an ac beta has been defined as the changes of collector current (IC) compared to the changes of base current (IB) where IC and IB are determined at operating point.
•On data sheet, ac=hfe
•It can defined by the following equation:

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Example

From output characteristics of common emitter configuration, find ac and dc with an Operating point at IB=25 A and VCE =7.5V.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Solution

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Relationship analysis between α and β

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Common – Collector Configuration

•Also called emitter-follower (EF).
•It is called common-emitter configuration since both the
signal source and the load share the collector terminal as a common connection point.
•The output voltage is obtained at emitter terminal.
•The input characteristic of common-collector configuration is similar with common-emitter. configuration.
•Common-collector circuit configuration is provided with the load resistor connected from emitter to ground.
•It is used primarily for impedance-matching purpose since it has high input impedance and low output impedance.

Bipolar Junction Transistor (BJT) ---------------------------------------------------------- Next Slide

Limits of Operation
•Many BJT transistor used as an amplifier. Thus it is
important to notice the limits of operations.
•At least 3 maximum values is mentioned in data sheet.
•There are:
a) Maximum power dissipation at collector: PCmax or PD
b) Maximum collector-emitter voltage: VCEmax sometimes named as VBR(CEO) or VCEO.
c) Maximum collector current: ICmax
•There are few rules that need to be followed for BJT
transistor used as an amplifier. The rules are:
i) transistor need to be operate in active region!
ii) IC < ICmax
ii) PC < PCmax