Computer Science Engineering (CSE) Exam > Computer Science Engineering (CSE) Notes > Chapter 5 - FM Receivers , PPT, Semester, Engineering
Chapter 5 - FM Receivers , PPT, Semester, Engineering - Computer Science Engineering (CSE) PDF Download
INTRODUCTION
FM Receivers ----------------------------------------------------- Next Slide
Double-Conversion Superheterodyne FM Receivers
FM Receivers ----------------------------------------------------- Next Slide
FM Receivers ----------------------------------------------------- Next Slide
FM DEMODULATION
Demodulation should provide an output signal whose amplitude is dependent on the instantaneous carrier frequency deviation and whose frequency is dependent on the rate of the carrier frequency change
FM Receivers ----------------------------------------------------- Next Slide
Slope Detector
1. simplest form of tuned-circuit frequency discriminator
2. Single ended slope has the most nonlinear voltage-versus-frequency characteristics à seldom used
3. Convert FM to AM - - > demodulate AM envelope with conventional peak detectors
4. Circuit consist of a tuned circuit and an AM detector
Disadvantages
1.Gain is reduced
2.Difficult to achieve a linear slope response curve
FM Receivers ----------------------------------------------------- Next Slide
FM Receivers ----------------------------------------------------- Next Slide
Circuit Operation (Figure 5.3)
1. La & Ca (tuned circuit) produce o/put voltage (amplitude varies) which is proportional to the i/put freq. (FM in)
- - -> AM characteristic
2. Maximum o/put voltage occurs at resonant freq of tank circuit, fo and its o/put decrease proportionately as the i/put freq deviates below & above fo
3. IF center frequency (fc) falls in the center of the most linear portion of the voltage-versus-frequency curve (Figure 5.3(b))
4. When IF deviates above fc, output voltage increase and when IF deviated below fc, output voltage decrease.
5. The tuned circuit converts frequency variations to amplitude variations (FM-to-AM conversion).
6. Di, Ci and Ri - - -> simple peak detector that converts amplitude variations to o/put voltage (operate as AM Diode Detector)
• o/put voltage varies at a rate equal to i/put frequency
• Amplitude of o/put voltage depend on magnitude of freq changes
FM Receivers ----------------------------------------------------- Next Slide
Balanced slope detector
Figure 5.4: Balanced slope detector (a) schematic diagram (b) voltage-versus-frequency response curve.
FM Receivers ----------------------------------------------------- Next Slide
• made up of single-ended slope detector connected in parallel and fed 180o out of phase (phase inversion).
• the 2 tuned circuit perform the FM to AM conversions
• At resonant freq, the resultant output voltage is 0 V.
• As the IF deviates above the center freq, top tuned circuit produces higher voltage than the lower tank circuit (+Vout) and vice versa.
• Figure 5.4(b) shows the output versus frequency response curve.
• diode detector circuit (D1,R1,C1 & D2,R2,C2) recover the original signal.
• advantage : simple.
• disadvantages : poor linearity, difficult in tuning and lack of provisions for limiting.
FM Receivers ----------------------------------------------------- Next Slide
Foster Seeley Discriminator
• Also called phase shift discriminator (tuned-circuit frequency discriminator) à operation very similar to the balanced slope detector
• Is tuned by injecting a frequency equal to the IF center frequency and tuning C0 for 0 volts out.
• Output voltage is directly proportional to the magnitude and direction of the frequency deviation.
• Output voltage-versus-frequency deviation curve is more linear than that of a slope detector because there is only one tank circuit,
- - -> easier to tune.
• For distortion less demodulation, the frequency deviation should be restricted to the linear portion of the secondary tuned-circuit frequency response curve.
• Responds to amplitude as well as frequency variations and, therefore, must be preceded by a separate limiter circuit
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.5: Foster Seeley discriminator (a) schematic diagram (b)vector diagram, fin = fo; (b) fin > fo; (c) fin < fo
FM Receivers ----------------------------------------------------- Next Slide
Principle Circuit Operation
FM Receivers ----------------------------------------------------- Next Slide
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.6 : Discriminator voltage-versus-frequency response curve.
FM Receivers ----------------------------------------------------- Next Slide
Ratio detector
• Advantage : relatively immune to amplitude variations in its input signal.
• Figure 5.7 shows the schematic diagram for a ratio detector.
• Same as the Foster-Seeley discriminator but with 3 limiting changes.
1. D2 has been reversed à current (Id) flow through the outermost loop of the circuit
2. Shunt capacitor, Cs charges to approximately the peak voltage across the secondary winding of T1. The reactance of Cs is low, and Rs simply provides a dc path for diode current.
3. Therefore, the time constant for Rs and Cs is sufficiently long so that rapid changes in the amplitude of the input signal due to thermal noise or other interfering signals are shorted to ground and have no effect on the average voltage across Cs.
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.7 : Ratio detector (a) schematic diagram; (b) voltage-versus-frequency response curve
FM Receivers ----------------------------------------------------- Next Slide
• Consequently, C1 and C2 charge and discharge proportional to frequency changes in the input signal and are relatively immune to amplitude variations.
• Also, the output voltage from a ratio detector is taken with respect to ground, and for the diode polarities shown in Figure 5.7(a), the average output voltage is positive.
• At resonance, the output voltage is divided equally between C1 and C2 and redistributed as the input frequency is deviated above and below resonance.
• Therefore, changes in Vout are due to the changing ratio of the voltage across C1 and C2, while the total voltage is clamped by Cs.
• Figure 5.7(b) shows the output frequency response curve for the ratio detector shown in Figure 5.7(a). It can be seen that at resonance, Vout is not equal to 0 V but, rather, to one-half of the voltage across the secondary windings of T1 . Because a ratio detector is relatively immune to amplitude variations, it is often selected over a discriminator.
• However, a discriminator produces a more linear output voltage-versus-frequency response curve.
FM Receivers ----------------------------------------------------- Next Slide
PHASE LOCKED LOOP (PLL)
• FM demodulation can be accomplished quite simply with a phase-locked loop (PLL).
• PLL FM demodulator is probably the simplest and easiest to understand.
• A PLL frequency demodulator requires no tuned circuits and automatically compensates for changes in the carrier frequency due to instability in the transmit oscillator.
• Figure 5.8(a) shows the simplified block diagram for a PLL FM demodulator.
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.8 (a) Block diagram for a PLL FM demodulator.
FM Receivers ----------------------------------------------------- Next Slide
• If the IF amplitude is sufficiently limited prior to reaching the PLL and the loop is properly compensated, the PLL loop gain is constant and equal to KV.
• after frequency lock had occurred the VCO would track frequency changes in the input signal by maintaining a phase error at the input of the phase comparator.
• Therefore, if the PLL input is a deviated FM signal and the VCO natural frequency is equal to the IF center frequency, the correction voltage produced at the output of the phase comparator and fed back to the input of the VCO is proportional to the frequency deviation and is, thus, the demodulated information signal.
• Therefore, the demodulated signal can be taken directly from the output of the internal buffer and is mathematically given as
Vout = Δf Kd Ka
FM Receivers ----------------------------------------------------- Next Slide
• Figure 5.8(b) shows a schematic diagram for an FM demodulator using the XR-2212. R0 and C0 are course adjustments for setting the VCO's free-running frequency. Rx is for fine tuning, and RF and Rc set the internal op-amp voltage gain (Ka). The PLL closed-loop frequency response should be compensated to allow un-attenuated demodulation of the entire information signal bandwidth.
• The PLL op-amp provides voltage gain and current drive stability
• PLL is the best frequency demodulator, because the filtering circuit removes noise and interference and its linear output reproduce the output signal
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.8 (b) PLL FM demodulator using the XR-2212 PLL
FM Receivers ----------------------------------------------------- Next Slide
LIMITER
• If noise or other interference perturbs the amplitude of the carrier, then the carrier amplitude variations will cause distortion at the output.
• This distortion can be removed by passing through a limiter prior to the differentiator (demodulator)
• The limiter output must then be converted to a sinusoid by passing it through a band-pass filter with center frequency and sufficient bandwidth to pass the varying fundamental.
• The result is a constant amplitude sinusoid, which is differentiated and passed through the envelope detector to produce the desired signal.
• Improve S/N as much as 20 dB.
FM Receivers ----------------------------------------------------- Next Slide
Figure 5.9 Amplitude limiter input and output waveforms:
(a) input waveform; (b) output waveform
(a) input waveform; (b) output waveform
FM Receivers ----------------------------------------------------- Next Slide
FIGURE 5.10 Limiter output:
(a) captured by noise; (b) captured by signal.
FM Receivers ----------------------------------------------------- Next Slide
FM STEREO TRANSMITTER
• Broadcast of high fidelity stereo began in 1961 of FM radio
• The transmission of 2 channels of sound information (stereophonic) on a single carrier require compatibility with existing high-fidelity monophonic FM receiver
• FDM is used to combine the two audio
Figure 5.11
FM Receivers ----------------------------------------------------- Next Slide
FIGURE 5.12: Stereo FM transmitter using frequency-division multiplexing
FM Receivers ----------------------------------------------------- Next Slide
From Figure 5.12
• Both L & R channel will be added to the 2 adder circuits
1. 1st adder : (L + R) channel (50Hz ~ 15KHz) - -> total mono audio signal for compatibility
2. 2nd adder : (L – R) channel (50Hz ~ 15KHz)
♦ R channel is inverted and then added to adder circuit
• Delay network
1. (L – R) channel have delay which is introduced by signal path as it propagates via the balanced modulator
2. (L + R) channel must maintain its phase integrity with (L – R) channel to prevent phase error at further process.
• Balanced modulator
1. AM DSB-SC which modulate (L – R) channel with frequency subcarrier 38KHz
2. Produce ( L – R) sidebands with bandwidth 23KHz ~ 53KHz
• Multiplier x2
1. Multiply 19KHz oscillator by 2 to produce 38KHz subcarrier
• Linear combining network
1. Combine (L + R) channel, (L – R) channel, 19KHz stereo pilot and SCA (Subsidiary Communication Authorization) 60KHz ~ 74KHz
2. Produce composite baseband to be modulated with main station carrier
• SCA is used to broadcast uninterrupted music to private subscriber (not compulsory to be combined by fundamental of FM Broadcast)
FM Receivers ----------------------------------------------------- Next Slide
• The 19kHz pilot frequency fits between (L + R) and DSBSC (L – R) signals in the baseband frequency spectrum
• All three signals are added together to form the composite stereo broadband signal, which will modulate the main station carrier
• The pilot frequency is made small enough so that its FM deviation of the carrier is only ≈ 10% of the total ±75kHz maximum deviation allowed
• After the FM stereo is received and demodulated to baseband, the 19kHz pilot is used to phase lock an oscillator, which provides the 38 kHz subcarrier for the demodulation of the (L – R) signal.
FM Receivers ----------------------------------------------------- Next Slide
FM Baseband Spectrum
FIGURE 5.13 : Composite baseband spectrum
FM Receivers ----------------------------------------------------- Next Slide
FM STEREO RECEIVER
• All new FM broadcast receivers are being built with provision for receiving stereo, or two-channel broadcasts.
• The left (L) and right (R) channel signals from the program material are combined to form two different signals, one of which is the left-plus-right signal and one of which is the left-minus-right signal
• The (L - R) signal is double-sideband suppressed carrier (DSBSC) modulated about a carrier frequency of 38 kHz, with the LSB in the 23- to 38-kHz slot and the USB in the 38- to 53-kHz slot. The (L + R) signal is placed directly in the 0- to 15-kHz slot, and a pilot carrier at 19 kHz is added to synchronize the demodulator at the receiver.
• The output from the FM detector is a composite audio signal containing the frequency-multiplexed (L + R) and (L - R) signals and the 19-kHz pilot tone. This composite signal is applied directly to the input of the decode matrix.
FIGURE 5.14
FM Receivers ----------------------------------------------------- Next Slide
• The composite audio signal is also applied to one input of a phase-error detector circuit, which is part of a phase locked loop 38-kHz oscillator.
• The output drives the 38-kHz voltage-controlled oscillator, whose output provides the synchronous carrier for the demodulator.
• The oscillator output is also frequency divided by 2 (in a counter circuit) and applied to the other input of the phase comparator to close the phase locked loop.
• The phase-error signal is also passed to a Schmitt trigger circuit, which drives an indicator lamp on the panel that lights when the error signal goes to zero, indicating the presence of a synchronizing input signal (the 19-kHz pilot tone).
• The outputs from the 38-kHz oscillator and the filtered composite audio signals are applied to the balanced demodulator, whose output is the (L - R) channel.
FM Receivers ----------------------------------------------------- Next Slide
• The ( L + R) and (L - R) signals are passed through a matrix circuit that separates the L and R signals from each other. These are passed through de-emphasis networks and low-pass filters to remove unwanted high-frequency components and are then passed to the two channel audio amplifiers and speakers.
• On reception of a monaural signal, the pilot-tone indicator circuit goes off, indicating the absence of pilot tone, and closes the switch to disable the (L - R) input to the matrix.
• The (L + R) signal is passed through the matrix to both outputs. An ordinary monaural receiver tuned to a stereo signal would produce only the (L + R) signal, since all frequencies above 15 kHz are removed by filtering, and no demodulator circuitry is present.
• Thus the stereo signal is compatible with the monaural receivers.
FM Receivers ----------------------------------------------------- Next Slide
FIGURE 5.15 FM stereo and mono receiver
The document Chapter 5 - FM Receivers , PPT, Semester, Engineering - Computer Science Engineering (CSE) is a part of Computer Science Engineering (CSE) category.
All you need of Computer Science Engineering (CSE) at this link: Computer Science Engineering (CSE)
FAQs on Chapter 5 - FM Receivers , PPT, Semester, Engineering - Computer Science Engineering (CSE)
| 1. What is an FM receiver? |  |
An FM receiver is a device that is used to receive and demodulate Frequency Modulated (FM) signals. It is commonly used in radio broadcasting systems to receive FM radio signals and convert them into audio signals that can be heard through speakers or headphones.
| 2. How does an FM receiver work? | |
An FM receiver works by first receiving the FM signal, which consists of a carrier wave that is modulated by the audio signal. The receiver then demodulates the FM signal to extract the audio signal. This is done by using a circuit called a frequency discriminator, which measures the difference in frequency between the carrier wave and the modulated signal. The output of the frequency discriminator is then amplified and processed to produce the audio signal.
| 3. What are the advantages of FM receivers? | |
FM receivers have several advantages over other types of radio receivers. Firstly, FM signals are less susceptible to interference and noise compared to AM signals, resulting in clearer audio reception. Additionally, FM receivers can provide stereo sound, which is not possible with AM receivers. FM receivers also have a wider bandwidth, allowing for better audio quality and the ability to transmit additional information such as RDS (Radio Data System) data.
| 4. What are the main components of an FM receiver? | |
The main components of an FM receiver include an antenna, a tuner, a frequency discriminator, and an audio amplifier. The antenna picks up the FM signal from the air and sends it to the tuner, which selects the desired frequency. The tuned signal is then passed through the frequency discriminator, which demodulates the FM signal. Finally, the demodulated audio signal is amplified by the audio amplifier and sent to the output device, such as speakers or headphones.
| 5. How can FM receivers be used in practical applications? | |
FM receivers have a wide range of practical applications. They are commonly used in radio broadcasting systems to receive FM radio signals. FM receivers can also be found in car radios, portable radios, and stereo systems. Additionally, FM receivers are used in wireless communication systems, such as wireless microphones and wireless headphones, where they receive FM signals from a transmitter.
Related Exams
About this Document
|
1.4K Views |
|
4.91/5 Rating |
|
Dec 12, 2024 Last updated |
Document Description: Chapter 5 - FM Receivers , PPT, Semester, Engineering for Computer Science Engineering (CSE) 2024 is part of Computer Science Engineering (CSE) preparation. The notes and questions for Chapter 5 - FM Receivers , PPT, Semester, Engineering have been prepared according to the Computer Science Engineering (CSE) exam syllabus. Information about Chapter 5 - FM Receivers , PPT, Semester, Engineering covers topics like and Chapter 5 - FM Receivers , PPT, Semester, Engineering Example, for Computer Science Engineering (CSE) 2024 Exam. Find important definitions, questions, notes, meanings, examples, exercises and tests below for Chapter 5 - FM Receivers , PPT, Semester, Engineering.
Introduction of Chapter 5 - FM Receivers , PPT, Semester, Engineering in English is available as part of
our Computer Science Engineering (CSE) preparation & Chapter 5 - FM Receivers , PPT, Semester, Engineering in Hindi for Computer Science Engineering (CSE)
courses. Download more important topics, notes, lectures and mock test series for Computer Science Engineering (CSE)
Exam by signing up for free. Computer Science Engineering (CSE): Chapter 5 - FM Receivers , PPT, Semester, Engineering - Computer Science Engineering (CSE)
Description
Full syllabus notes, lecture & questions for Chapter 5 - FM Receivers , PPT, Semester, Engineering - Computer Science Engineering (CSE) - Computer Science Engineering (CSE) | Plus excerises question with solution to help you revise complete syllabus | Best notes, free PDF download
Information about Chapter 5 - FM Receivers , PPT, Semester, Engineering
In this doc you can find the meaning of Chapter 5 - FM Receivers , PPT, Semester, Engineering defined & explained in the simplest way possible.
Besides explaining types of Chapter 5 - FM Receivers , PPT, Semester, Engineering theory,
EduRev gives you an ample number of questions to practice Chapter 5 - FM Receivers , PPT, Semester, Engineering tests, examples and also practice Computer Science Engineering (CSE) tests.
Download as PDF
|
Explore Courses for Computer Science Engineering (CSE) exam
|
|
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
Related Searches
past year papers
,Chapter 5 - FM Receivers
,Engineering - Computer Science Engineering (CSE)
,Extra Questions
,PPT
,video lectures
,PPT
,Summary
,Exam
,ppt
,mock tests for examination
,Free
,Semester Notes
,Objective type Questions
,MCQs
,Chapter 5 - FM Receivers
,Engineering - Computer Science Engineering (CSE)
,Previous Year Questions with Solutions
,Semester
,PPT
,study material
,Semester
,practice quizzes
,Sample Paper
,shortcuts and tricks
,Semester
,Important questions
,Engineering - Computer Science Engineering (CSE)
,Viva Questions
,Chapter 5 - FM Receivers
;
Additional Information about Chapter 5 - FM Receivers , PPT, Semester, Engineering for Computer Science Engineering (CSE) Preparation
Chapter 5 - FM Receivers , PPT, Semester, Engineering Free PDF Download
The Chapter 5 - FM Receivers , PPT, Semester, Engineering is an invaluable resource that delves deep into the core of the Computer Science Engineering (CSE) exam.
These study notes are curated by experts and cover all the essential topics and concepts, making your preparation more efficient and effective.
With the help of these notes, you can grasp complex subjects quickly, revise important points easily,
and reinforce your understanding of key concepts. The study notes are presented in a concise and easy-to-understand manner,
allowing you to optimize your learning process. Whether you're looking for best-recommended books, sample papers, study material,
or toppers' notes, this PDF has got you covered. Download the Chapter 5 - FM Receivers , PPT, Semester, Engineering now and kickstart your journey towards success in the Computer Science Engineering (CSE) exam.
Importance of Chapter 5 - FM Receivers , PPT, Semester, Engineering
The importance of Chapter 5 - FM Receivers , PPT, Semester, Engineering cannot be overstated, especially for Computer Science Engineering (CSE) aspirants.
This document holds the key to success in the Computer Science Engineering (CSE) exam.
It offers a detailed understanding of the concept, providing invaluable insights into the topic.
By knowing the concepts well in advance, students can plan their preparation effectively.
Utilize this indispensable guide for a well-rounded preparation and achieve your desired results.
Chapter 5 - FM Receivers , PPT, Semester, Engineering Notes
Chapter 5 - FM Receivers , PPT, Semester, Engineering Notes offer in-depth insights into the specific topic to help you master it with ease.
This comprehensive document covers all aspects related to Chapter 5 - FM Receivers , PPT, Semester, Engineering.
It includes detailed information about the exam syllabus, recommended books, and study materials for a well-rounded preparation.
Practice papers and question papers enable you to assess your progress effectively.
Additionally, the paper analysis provides valuable tips for tackling the exam strategically.
Access to Toppers' notes gives you an edge in understanding complex concepts.
Whether you're a beginner or aiming for advanced proficiency, Chapter 5 - FM Receivers , PPT, Semester, Engineering Notes on EduRev are your ultimate resource for success.
Chapter 5 - FM Receivers , PPT, Semester, Engineering Computer Science Engineering (CSE) Questions
The "Chapter 5 - FM Receivers , PPT, Semester, Engineering Computer Science Engineering (CSE) Questions" guide is a valuable resource for all aspiring students preparing for the
Computer Science Engineering (CSE) exam. It focuses on providing a wide range of practice questions to help students gauge
their understanding of the exam topics. These questions cover the entire syllabus, ensuring comprehensive preparation.
The guide includes previous years' question papers for students to familiarize themselves with the exam's format and difficulty level.
Additionally, it offers subject-specific question banks, allowing students to focus on weak areas and improve their performance.
Study Chapter 5 - FM Receivers , PPT, Semester, Engineering on the App
Students of Computer Science Engineering (CSE) can study Chapter 5 - FM Receivers , PPT, Semester, Engineering alongwith tests & analysis from the EduRev app,
which will help them while preparing for their exam. Apart from the Chapter 5 - FM Receivers , PPT, Semester, Engineering,
students can also utilize the EduRev App for other study materials such as previous year question papers, syllabus, important questions, etc.
The EduRev App will make your learning easier as you can access it from anywhere you want.
The content of Chapter 5 - FM Receivers , PPT, Semester, Engineering is prepared as per the latest Computer Science Engineering (CSE) syllabus.
|
© EduRev
|
Education Revolution
|
Follow Us
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup