Electrical Engineering (EE) 2004 GATE Paper without solution (unsolved) GATE Notes | EduRev

GATE : Electrical Engineering (EE) 2004 GATE Paper without solution (unsolved) GATE Notes | EduRev

 Page 1


GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
Q.1 – Q.30 Carry One Mark Each 
 
1. The value of Z in Figure.Q.1, which is most appropriate to cause parallel 
resonance at 500 Hz, is 
 (a) 125.00 mH 
 (b) 304.20 µF 
 (c) 2.0 µF 
 (d) 0.05 µF 
  
2. A parallel plate capacitor is shown in figure Q.2. It is made of two square metal 
plates of 400 mm side. The 14 mm space between the plates is filled with two 
layers od dielectrics of 4,6
r
e = mm thick and 2,8
r
e = mm thick. Neglecting 
fringing of fields at the edges the capacitance is 
 (a) 1298 pF 
 (b) 944 pF 
 (c) 354 pF 
 (d) 257 pF 
 
 
 
3. The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 
turns on a cylindrical paper tube of 60mm diameter is 
 (a) 3.2 µH (b) 3.2 mH (c) 32.0 mH (d) 3.2 H 
 
4. Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L 
load is 
 (a) zero   (b) constant 
 (c) pulsating with zero average (d) pulsating with non-zero average 
 
5. A 500 kVA, 3-phase transformer has iron loses of 300 W and full load copper 
losses of 600 W. The percentage load at which the transformer is expected to 
have maximum efficiency is
 
 (a) 50.0% (b) 70.7% (c) 141.4% (d) 200.0% 
 
6. For a given stepper motor, the following torque has the highest numerical value. 
 (a) Detent torque   (b) Pull-in torque 
 (c) Pull-out torque   (d) Holding torque 
 
 
 
~ 
Z 
5O 
2H 
e r=4;d=6mm 
e r=2;d=8mm 
e 0=8.85×10
-12
F/m 
Page 2


GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
Q.1 – Q.30 Carry One Mark Each 
 
1. The value of Z in Figure.Q.1, which is most appropriate to cause parallel 
resonance at 500 Hz, is 
 (a) 125.00 mH 
 (b) 304.20 µF 
 (c) 2.0 µF 
 (d) 0.05 µF 
  
2. A parallel plate capacitor is shown in figure Q.2. It is made of two square metal 
plates of 400 mm side. The 14 mm space between the plates is filled with two 
layers od dielectrics of 4,6
r
e = mm thick and 2,8
r
e = mm thick. Neglecting 
fringing of fields at the edges the capacitance is 
 (a) 1298 pF 
 (b) 944 pF 
 (c) 354 pF 
 (d) 257 pF 
 
 
 
3. The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 
turns on a cylindrical paper tube of 60mm diameter is 
 (a) 3.2 µH (b) 3.2 mH (c) 32.0 mH (d) 3.2 H 
 
4. Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L 
load is 
 (a) zero   (b) constant 
 (c) pulsating with zero average (d) pulsating with non-zero average 
 
5. A 500 kVA, 3-phase transformer has iron loses of 300 W and full load copper 
losses of 600 W. The percentage load at which the transformer is expected to 
have maximum efficiency is
 
 (a) 50.0% (b) 70.7% (c) 141.4% (d) 200.0% 
 
6. For a given stepper motor, the following torque has the highest numerical value. 
 (a) Detent torque   (b) Pull-in torque 
 (c) Pull-out torque   (d) Holding torque 
 
 
 
~ 
Z 
5O 
2H 
e r=4;d=6mm 
e r=2;d=8mm 
e 0=8.85×10
-12
F/m 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
R 
Y 
B 
7. The following motor definitely has a permanent magnet rotor 
 (a) DC commutator motor (b) Brushless dc motor 
 (c) Stepper motor   (d) Reluctance motor 
 
8. The type of single-phase induction motor having the highest power factor at full 
load is 
 (a) shaded pole type   (b) split-phase type 
 (c) capacitor-start type  (d) capacitor-run type 
 
9. The direction of rotation of a 3-phase induction motor is clockwise when it is 
supplied with 3-phase sinusoidal voltage having phase sequence A-B-C. For 
counter clockwise rotation of the motor, the phase sequence of the power supply 
should be 
 (a) B-C-A   (b) C-A-B 
 (c) A-C-B   (d) B-C-A or C-A-B 
 
10. For a linear electromagnetic circuit, the following statement is true. 
 (a) Field energy is equal to the co-energy 
 (b) Field energy is greater than the co-energy 
 (c) Field energy is lesser than the co-energy 
 (d) Co-energy is zero 
 
11. The rated voltage of a 3-phase power system is given as 
 (a) rms phase voltage  (b) peak phase voltage 
 (c) rms line to line voltage (d) peak line to line voltage 
 
12.  The phase sequence of the 3-phase system shown in Figure is 
 
 
 
 
 
 
 (a) RYB (b) RBY (c) BRY (d) YBR 
 
13. In thermal power plants, the pressure in the working fluid cycle is developed by 
 (a) condenser   (b) super heater  
 (c) feed water pump   (d) turbine 
 
Page 3


GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
Q.1 – Q.30 Carry One Mark Each 
 
1. The value of Z in Figure.Q.1, which is most appropriate to cause parallel 
resonance at 500 Hz, is 
 (a) 125.00 mH 
 (b) 304.20 µF 
 (c) 2.0 µF 
 (d) 0.05 µF 
  
2. A parallel plate capacitor is shown in figure Q.2. It is made of two square metal 
plates of 400 mm side. The 14 mm space between the plates is filled with two 
layers od dielectrics of 4,6
r
e = mm thick and 2,8
r
e = mm thick. Neglecting 
fringing of fields at the edges the capacitance is 
 (a) 1298 pF 
 (b) 944 pF 
 (c) 354 pF 
 (d) 257 pF 
 
 
 
3. The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 
turns on a cylindrical paper tube of 60mm diameter is 
 (a) 3.2 µH (b) 3.2 mH (c) 32.0 mH (d) 3.2 H 
 
4. Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L 
load is 
 (a) zero   (b) constant 
 (c) pulsating with zero average (d) pulsating with non-zero average 
 
5. A 500 kVA, 3-phase transformer has iron loses of 300 W and full load copper 
losses of 600 W. The percentage load at which the transformer is expected to 
have maximum efficiency is
 
 (a) 50.0% (b) 70.7% (c) 141.4% (d) 200.0% 
 
6. For a given stepper motor, the following torque has the highest numerical value. 
 (a) Detent torque   (b) Pull-in torque 
 (c) Pull-out torque   (d) Holding torque 
 
 
 
~ 
Z 
5O 
2H 
e r=4;d=6mm 
e r=2;d=8mm 
e 0=8.85×10
-12
F/m 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
R 
Y 
B 
7. The following motor definitely has a permanent magnet rotor 
 (a) DC commutator motor (b) Brushless dc motor 
 (c) Stepper motor   (d) Reluctance motor 
 
8. The type of single-phase induction motor having the highest power factor at full 
load is 
 (a) shaded pole type   (b) split-phase type 
 (c) capacitor-start type  (d) capacitor-run type 
 
9. The direction of rotation of a 3-phase induction motor is clockwise when it is 
supplied with 3-phase sinusoidal voltage having phase sequence A-B-C. For 
counter clockwise rotation of the motor, the phase sequence of the power supply 
should be 
 (a) B-C-A   (b) C-A-B 
 (c) A-C-B   (d) B-C-A or C-A-B 
 
10. For a linear electromagnetic circuit, the following statement is true. 
 (a) Field energy is equal to the co-energy 
 (b) Field energy is greater than the co-energy 
 (c) Field energy is lesser than the co-energy 
 (d) Co-energy is zero 
 
11. The rated voltage of a 3-phase power system is given as 
 (a) rms phase voltage  (b) peak phase voltage 
 (c) rms line to line voltage (d) peak line to line voltage 
 
12.  The phase sequence of the 3-phase system shown in Figure is 
 
 
 
 
 
 
 (a) RYB (b) RBY (c) BRY (d) YBR 
 
13. In thermal power plants, the pressure in the working fluid cycle is developed by 
 (a) condenser   (b) super heater  
 (c) feed water pump   (d) turbine 
 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
14. For harnessing low variable water heads, the suitable hydraulic turbine with high 
percentage of reaction and runner adjustable vanes is 
 (a) Kaplan (b) Francis (c) Pelton (d) Impeller 
 
15. The transmission line distance protection relay having the property of being 
inherently directional is 
 (a) impedance relay   (b) MHO relay 
 (c) OHM relay   (d) reactance relay 
 
16. The current through the Zener diode in figure is 
 
 
 
 
 
 
 (a) 33 mA (b) 3.3 mA (c) 2 mA (d) 0 mA 
 
17. Two perfectly matched silicon transistors are connected as shown in figure. The 
value of the current I is 
 
 
 
 
 
 
 
 
 
 (a) 0 mA (b) 2.3 mA (c) 4.3 mA (d) 7.3 mA 
 
 
 
 
 
 
 
 
 
1kO 
+3V 
I 
ß=1000 ß=1000 
0.7V 
+ 
- 
-5V 
2.2kO 
3.5V 
I Z 
R 1 
+ 
- 
10V 
R Z=0.1kO 
V Z=3.3V 
Page 4


GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
Q.1 – Q.30 Carry One Mark Each 
 
1. The value of Z in Figure.Q.1, which is most appropriate to cause parallel 
resonance at 500 Hz, is 
 (a) 125.00 mH 
 (b) 304.20 µF 
 (c) 2.0 µF 
 (d) 0.05 µF 
  
2. A parallel plate capacitor is shown in figure Q.2. It is made of two square metal 
plates of 400 mm side. The 14 mm space between the plates is filled with two 
layers od dielectrics of 4,6
r
e = mm thick and 2,8
r
e = mm thick. Neglecting 
fringing of fields at the edges the capacitance is 
 (a) 1298 pF 
 (b) 944 pF 
 (c) 354 pF 
 (d) 257 pF 
 
 
 
3. The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 
turns on a cylindrical paper tube of 60mm diameter is 
 (a) 3.2 µH (b) 3.2 mH (c) 32.0 mH (d) 3.2 H 
 
4. Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L 
load is 
 (a) zero   (b) constant 
 (c) pulsating with zero average (d) pulsating with non-zero average 
 
5. A 500 kVA, 3-phase transformer has iron loses of 300 W and full load copper 
losses of 600 W. The percentage load at which the transformer is expected to 
have maximum efficiency is
 
 (a) 50.0% (b) 70.7% (c) 141.4% (d) 200.0% 
 
6. For a given stepper motor, the following torque has the highest numerical value. 
 (a) Detent torque   (b) Pull-in torque 
 (c) Pull-out torque   (d) Holding torque 
 
 
 
~ 
Z 
5O 
2H 
e r=4;d=6mm 
e r=2;d=8mm 
e 0=8.85×10
-12
F/m 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
R 
Y 
B 
7. The following motor definitely has a permanent magnet rotor 
 (a) DC commutator motor (b) Brushless dc motor 
 (c) Stepper motor   (d) Reluctance motor 
 
8. The type of single-phase induction motor having the highest power factor at full 
load is 
 (a) shaded pole type   (b) split-phase type 
 (c) capacitor-start type  (d) capacitor-run type 
 
9. The direction of rotation of a 3-phase induction motor is clockwise when it is 
supplied with 3-phase sinusoidal voltage having phase sequence A-B-C. For 
counter clockwise rotation of the motor, the phase sequence of the power supply 
should be 
 (a) B-C-A   (b) C-A-B 
 (c) A-C-B   (d) B-C-A or C-A-B 
 
10. For a linear electromagnetic circuit, the following statement is true. 
 (a) Field energy is equal to the co-energy 
 (b) Field energy is greater than the co-energy 
 (c) Field energy is lesser than the co-energy 
 (d) Co-energy is zero 
 
11. The rated voltage of a 3-phase power system is given as 
 (a) rms phase voltage  (b) peak phase voltage 
 (c) rms line to line voltage (d) peak line to line voltage 
 
12.  The phase sequence of the 3-phase system shown in Figure is 
 
 
 
 
 
 
 (a) RYB (b) RBY (c) BRY (d) YBR 
 
13. In thermal power plants, the pressure in the working fluid cycle is developed by 
 (a) condenser   (b) super heater  
 (c) feed water pump   (d) turbine 
 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
14. For harnessing low variable water heads, the suitable hydraulic turbine with high 
percentage of reaction and runner adjustable vanes is 
 (a) Kaplan (b) Francis (c) Pelton (d) Impeller 
 
15. The transmission line distance protection relay having the property of being 
inherently directional is 
 (a) impedance relay   (b) MHO relay 
 (c) OHM relay   (d) reactance relay 
 
16. The current through the Zener diode in figure is 
 
 
 
 
 
 
 (a) 33 mA (b) 3.3 mA (c) 2 mA (d) 0 mA 
 
17. Two perfectly matched silicon transistors are connected as shown in figure. The 
value of the current I is 
 
 
 
 
 
 
 
 
 
 (a) 0 mA (b) 2.3 mA (c) 4.3 mA (d) 7.3 mA 
 
 
 
 
 
 
 
 
 
1kO 
+3V 
I 
ß=1000 ß=1000 
0.7V 
+ 
- 
-5V 
2.2kO 
3.5V 
I Z 
R 1 
+ 
- 
10V 
R Z=0.1kO 
V Z=3.3V 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
18. The feedback used in the circuit shown in figure can be classified as 
 
 
 
 
 
 
 
 
 
 
 (a) shunt-series feedback  (b) shunt-shunt feedback 
 (c) series-shunt feedback  (d) series-series feedback 
19. The digital circuit using two inverters shown in figure will act as 
 (a) a bistable multi-vibrator 
 (b) an astable mutli-vibrator 
 (c) a monostable multi-vibrator 
 (d) an oscillator 
 
20. The voltage comparator shown in figure can be used in the analog-to-digital 
conversion as 
 (a) a 1-bit quantizer 
 (b) a 2-bit quantizer 
 (c) a 4-bit quantizer 
 (d) a 8-bit quantizer 
 
21. The Nyquist plot of loop transfer function G(s) H(s) of a closed loop control 
system passes through the point (-1,j0) in the G(s) H(s) plane. The phase margin 
of the system is 
 (a) 0° (b) 45° (c) 90° (d) 180° 
 
22. Consider the function ( )
( )
2
5
3 2
F s
s s s
=
+ +
, where F(s) is the Laplace transform 
of the function f(t). the initial value of f(t) is equal to  
 (a) 5 (b) 
5
2
 (c) 
5
3
 (d) 0 
 
R F 
R B 
R E 
C=x 
C=x 
C=x R 1 
R C 
V CC 
R S 
+ 
- 
V O 
V 1 
V 2 
Page 5


GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
Q.1 – Q.30 Carry One Mark Each 
 
1. The value of Z in Figure.Q.1, which is most appropriate to cause parallel 
resonance at 500 Hz, is 
 (a) 125.00 mH 
 (b) 304.20 µF 
 (c) 2.0 µF 
 (d) 0.05 µF 
  
2. A parallel plate capacitor is shown in figure Q.2. It is made of two square metal 
plates of 400 mm side. The 14 mm space between the plates is filled with two 
layers od dielectrics of 4,6
r
e = mm thick and 2,8
r
e = mm thick. Neglecting 
fringing of fields at the edges the capacitance is 
 (a) 1298 pF 
 (b) 944 pF 
 (c) 354 pF 
 (d) 257 pF 
 
 
 
3. The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 
turns on a cylindrical paper tube of 60mm diameter is 
 (a) 3.2 µH (b) 3.2 mH (c) 32.0 mH (d) 3.2 H 
 
4. Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L 
load is 
 (a) zero   (b) constant 
 (c) pulsating with zero average (d) pulsating with non-zero average 
 
5. A 500 kVA, 3-phase transformer has iron loses of 300 W and full load copper 
losses of 600 W. The percentage load at which the transformer is expected to 
have maximum efficiency is
 
 (a) 50.0% (b) 70.7% (c) 141.4% (d) 200.0% 
 
6. For a given stepper motor, the following torque has the highest numerical value. 
 (a) Detent torque   (b) Pull-in torque 
 (c) Pull-out torque   (d) Holding torque 
 
 
 
~ 
Z 
5O 
2H 
e r=4;d=6mm 
e r=2;d=8mm 
e 0=8.85×10
-12
F/m 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
R 
Y 
B 
7. The following motor definitely has a permanent magnet rotor 
 (a) DC commutator motor (b) Brushless dc motor 
 (c) Stepper motor   (d) Reluctance motor 
 
8. The type of single-phase induction motor having the highest power factor at full 
load is 
 (a) shaded pole type   (b) split-phase type 
 (c) capacitor-start type  (d) capacitor-run type 
 
9. The direction of rotation of a 3-phase induction motor is clockwise when it is 
supplied with 3-phase sinusoidal voltage having phase sequence A-B-C. For 
counter clockwise rotation of the motor, the phase sequence of the power supply 
should be 
 (a) B-C-A   (b) C-A-B 
 (c) A-C-B   (d) B-C-A or C-A-B 
 
10. For a linear electromagnetic circuit, the following statement is true. 
 (a) Field energy is equal to the co-energy 
 (b) Field energy is greater than the co-energy 
 (c) Field energy is lesser than the co-energy 
 (d) Co-energy is zero 
 
11. The rated voltage of a 3-phase power system is given as 
 (a) rms phase voltage  (b) peak phase voltage 
 (c) rms line to line voltage (d) peak line to line voltage 
 
12.  The phase sequence of the 3-phase system shown in Figure is 
 
 
 
 
 
 
 (a) RYB (b) RBY (c) BRY (d) YBR 
 
13. In thermal power plants, the pressure in the working fluid cycle is developed by 
 (a) condenser   (b) super heater  
 (c) feed water pump   (d) turbine 
 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
14. For harnessing low variable water heads, the suitable hydraulic turbine with high 
percentage of reaction and runner adjustable vanes is 
 (a) Kaplan (b) Francis (c) Pelton (d) Impeller 
 
15. The transmission line distance protection relay having the property of being 
inherently directional is 
 (a) impedance relay   (b) MHO relay 
 (c) OHM relay   (d) reactance relay 
 
16. The current through the Zener diode in figure is 
 
 
 
 
 
 
 (a) 33 mA (b) 3.3 mA (c) 2 mA (d) 0 mA 
 
17. Two perfectly matched silicon transistors are connected as shown in figure. The 
value of the current I is 
 
 
 
 
 
 
 
 
 
 (a) 0 mA (b) 2.3 mA (c) 4.3 mA (d) 7.3 mA 
 
 
 
 
 
 
 
 
 
1kO 
+3V 
I 
ß=1000 ß=1000 
0.7V 
+ 
- 
-5V 
2.2kO 
3.5V 
I Z 
R 1 
+ 
- 
10V 
R Z=0.1kO 
V Z=3.3V 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
18. The feedback used in the circuit shown in figure can be classified as 
 
 
 
 
 
 
 
 
 
 
 (a) shunt-series feedback  (b) shunt-shunt feedback 
 (c) series-shunt feedback  (d) series-series feedback 
19. The digital circuit using two inverters shown in figure will act as 
 (a) a bistable multi-vibrator 
 (b) an astable mutli-vibrator 
 (c) a monostable multi-vibrator 
 (d) an oscillator 
 
20. The voltage comparator shown in figure can be used in the analog-to-digital 
conversion as 
 (a) a 1-bit quantizer 
 (b) a 2-bit quantizer 
 (c) a 4-bit quantizer 
 (d) a 8-bit quantizer 
 
21. The Nyquist plot of loop transfer function G(s) H(s) of a closed loop control 
system passes through the point (-1,j0) in the G(s) H(s) plane. The phase margin 
of the system is 
 (a) 0° (b) 45° (c) 90° (d) 180° 
 
22. Consider the function ( )
( )
2
5
3 2
F s
s s s
=
+ +
, where F(s) is the Laplace transform 
of the function f(t). the initial value of f(t) is equal to  
 (a) 5 (b) 
5
2
 (c) 
5
3
 (d) 0 
 
R F 
R B 
R E 
C=x 
C=x 
C=x R 1 
R C 
V CC 
R S 
+ 
- 
V O 
V 1 
V 2 
GATE EE - 2004                            www.gateforum.com 
                                        Join discussion of this test paper at http://forum.gatementor.com 
Join All India Mock GATE Classroom Test Series - 2007 conducted by GATE Forum in over 25 cities all over India. Question 
Papers including section tests and full tests are designed by IISc alumni according to the latest syllabus. Percentile, All India Rank, 
interaction with IISc alumni in our online discussion forums, and more. For more details,  
visit 
www.gateforum.com 
Think GATE Think GATE Forum 
23. For a tachometer if ?(t) is the rotor displacement is radians, e(t) is the output 
voltage and K
t
 is the tachometer constant in V/rad/sec, then the transfer 
function, 
( )
( )
E s
s T
will be 
 (a) 
2
t
K s (b) 
t
K
s
 (c) 
t
K s (d) 
t
K 
24. A dc potentiometer is designed to measure up to about 2V with a slide wire of 
300 mm.  A standard cell of emf 1.18 V obtains balance at 600 mm. A test cell is 
seen to obtain balance at 680 mm. The emf of the test cell is 
 (a) 1.00 V (b) 1.34 V (c) 1.50 V (d) 1.70 V 
 
25. The circuit in figure is used to measure the power consumed by the load. The 
current coil and the voltage coil of the wattmeter have 0.02O and 1000O 
resistances respectively. The measured power compared to the load power will be 
 (a) 0.4% less 
 (b) 0.2% less 
 (c) 0.2% more 
 (d) 0.4% more 
 
26. A galvanometer with a full-scale current of 10mA has a resistance of 1000O. The 
multiplying power (the ratio of measured current to galvanometer current) of a 
100O shunt with this galvanometer is 
 (a) 110 (b) 100 (c) 11 (d) 10 
 
27. A bipolar junction transistor (BJT) is used as a power control switch by biasing it 
in the cut-off region (OFF state) or in the saturation region (ON state). In the ON 
state, for the BJT  
 (a) both the base-emitter and base-collector junctions are reverse biased 
 (b) the base-emitter junctions is reverse biased, and the base-collector junction 
is forward biased 
 (c) the base-emitter junction is forward biased, and the base-collector junction is 
reverse biased 
 (d) both the base-emitter and base-collector junctions are forward biased 
 
28. The circuit in figure shows a full-wave rectifier. The input voltage is 230V (rms) 
single-phase ac. The peak reverse voltage across the diodes D1 and D2 is 
 (a) 100 2 V 
 (b) 100 V 
 (c) 50 2 V 
 (d) 50 V 
 
0.02O 
1000O 
200V 
20A 
Upf 
load 
230V/50-0-50V 
D 2 
230V,    
50 Hz, ac 
D 1 
Read More
Offer running on EduRev: Apply code STAYHOME200 to get INR 200 off on our premium plan EduRev Infinity!

Related Searches

mock tests for examination

,

Semester Notes

,

Free

,

shortcuts and tricks

,

MCQs

,

Electrical Engineering (EE) 2004 GATE Paper without solution (unsolved) GATE Notes | EduRev

,

Previous Year Questions with Solutions

,

past year papers

,

video lectures

,

pdf

,

Summary

,

Extra Questions

,

Important questions

,

Electrical Engineering (EE) 2004 GATE Paper without solution (unsolved) GATE Notes | EduRev

,

ppt

,

Exam

,

Objective type Questions

,

Viva Questions

,

study material

,

Electrical Engineering (EE) 2004 GATE Paper without solution (unsolved) GATE Notes | EduRev

,

practice quizzes

,

Sample Paper

;