Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

Digital Electronics

Electronics and Communication Engineering (ECE) : Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

The document Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev is a part of the Electronics and Communication Engineering (ECE) Course Digital Electronics.
All you need of Electronics and Communication Engineering (ECE) at this link: Electronics and Communication Engineering (ECE)

JK Flip-flops

Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

A Universal Programmable Flip-flop

The JK Flip-flop is also called a programmable flip-flop because, using its inputs, J, K, S and R, it can be made to mimic the action of any of the other flip-flop types.

Fig. 5.4.1 shows the basic configuration (without S and R inputs) for a JK flip-flop using only four NAND gates. The circuit is similar to the clocked SR flip-flop clocked SR flip-flop shown in Fig. 5.2.7, (Digital Electronics Module 5.2) but in Fig. 5.4.1, it can be seen that although the clock input is the same as in the clocked SR flip-flop, gate NAND 1 in Fig. 5.4.1 is now a three input gate and the set input (S) been replaced by an input labeled J, and the third input provides feedback from the Q output.

On NAND 2 the reset input (R) of Fig 5.2.7 has been replaced by input K and there is an additional feedback connection from Q. The purpose of this feedback is to eliminate the indeterminate state that occurred on the SR flip-flop when both inputs were made logic 0 at the same time.

Operation

As a starting point, assume that both J and K are at logic 1 and the outputs Q = 0 and Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev = 1, this will cause NAND 1 to be enabled, as it has logic 1 on two (J and Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev) of its three inputs, requiring only a logic 1 on its clock input to change its output state to logic 0. At the same time, NAND 2 is disabled, because it only has one of its inputs (K) at logic 1, its feedback input is at logic 0 because of the feedback from Q.

On the arrival of a clock pulse, the output of NAND 1 therefore becomes logic 0, and causes the flip-flop to change state so that Q = 1 and Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev = 0. This action enables NAND 2 and disables NAND 1.

As this change of state at the outputs occurs however, there is a problem. If the clock pulse is still high, or in its thold period when the flip-flop changes state, the output of NAND 2 will instantly go to logic 0 and the flip-flop will reset back to its original state. This can then set up a situation where the flip-flop will rapidly oscillate between its two states.

These problems caused by the output data ‘racing’ round the feedback lines from output to input before the end of the clock pulse are known as RACE HAZARDS and of course must be avoided. This can be done however, by using a more complex version of the circuit

Offer running on EduRev: Apply code STAYHOME200 to get INR 200 off on our premium plan EduRev Infinity!

Related Searches

video lectures

,

practice quizzes

,

Extra Questions

,

Summary

,

Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

,

mock tests for examination

,

shortcuts and tricks

,

Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

,

ppt

,

past year papers

,

Introduction To Jk - JK Flip Flops Electronics and Communication Engineering (ECE) Notes | EduRev

,

Objective type Questions

,

Viva Questions

,

MCQs

,

Free

,

study material

,

Important questions

,

Previous Year Questions with Solutions

,

Semester Notes

,

pdf

,

Exam

,

Sample Paper

;