Lecture 43 - Rectangular Wave Guide and Transverse Magnetic Mode Notes | EduRev

: Lecture 43 - Rectangular Wave Guide and Transverse Magnetic Mode Notes | EduRev

 Page 1


 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
   Objective
   In this course you will learn the following
General Approach to Wave Guide Analysis.
Transverse Magnetic Mode.
Boundary conditions for the longitudinal electric field.
Page 2


 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
   Objective
   In this course you will learn the following
General Approach to Wave Guide Analysis.
Transverse Magnetic Mode.
Boundary conditions for the longitudinal electric field.
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
General Approach to Wave Guide Analysis
In case of parallel wave guide the modal propagation was visualized as super position of multiply reflected plane wave
from the two conducting sheets. This approach although provides better physical understanding of the modal propagation,
becomes algebraically unmanagable for complicated waveguide in structure.
In the following we develop a general framework for analyzing the wave guide structure like a Rectangular Wave Guide.
A rectangular wave guide is a hollow metallic pipe with rectangular cross section. The electro magnetic energy
propagates along the length of pipe. The net wave propagation therefore is along the length of the pipe.
A direction along the length of the pipe is called the Longitudinal direction. Whereas any direction perpendicular to the
wave propagation is called the TRANSVERSE DIRECTION.
Let us choose the co-ordinate system such that the  - axis is along the longitudinal direction.
You can note that in general there are six field components, three for electric field nad three for magnetic field which are
related through Maxwell's equations. All the six components therefore cannot be independent. We can select to field
components as an independent components and the remaining four components can be obtained from the Maxwell's
equation.
Since the  - direction is a special direction(direction of the net wave propagation) we choose the longitudinal electric and
magnetic field components (  ,  ) as independent components and derive the transverse components in terms of
the longitudinal components using the Maxwell's equation.
Since the net wave is travelling in a  - direction any field component in the  - direction will be of the type  ,
where  is the phase constant of the net wave propagating along the  - direction.
If we define a parameter  (transverse propagation constant) as
 
we can write transverse electric and magnetic field in term of the longitudinal field components (  ,  ) as
    ----------- (6.28 )
    ----------- (6.29 )
Here  transverse is defined by
    ----------- (6.30 )
in Cartesians co-ordinate system.
 
From the above equations we can make some important observations as follows :
(1)
Transverse fields can exist provided at least one of the longitudinal components ( or ) is non-zero, except when 
= 0. That is, in general there is no transverse electromagnetic wave propagation except when .
(2)
For  we get  implying that the transverse electromagnetic wave can exist in a waveguide if its
propagation constant is same as that of the unbound medium filling the waveguide.
(3)
The fields corresponding to , have electric field transverse to the direction of wave propagation and hence
Page 3


 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
   Objective
   In this course you will learn the following
General Approach to Wave Guide Analysis.
Transverse Magnetic Mode.
Boundary conditions for the longitudinal electric field.
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
General Approach to Wave Guide Analysis
In case of parallel wave guide the modal propagation was visualized as super position of multiply reflected plane wave
from the two conducting sheets. This approach although provides better physical understanding of the modal propagation,
becomes algebraically unmanagable for complicated waveguide in structure.
In the following we develop a general framework for analyzing the wave guide structure like a Rectangular Wave Guide.
A rectangular wave guide is a hollow metallic pipe with rectangular cross section. The electro magnetic energy
propagates along the length of pipe. The net wave propagation therefore is along the length of the pipe.
A direction along the length of the pipe is called the Longitudinal direction. Whereas any direction perpendicular to the
wave propagation is called the TRANSVERSE DIRECTION.
Let us choose the co-ordinate system such that the  - axis is along the longitudinal direction.
You can note that in general there are six field components, three for electric field nad three for magnetic field which are
related through Maxwell's equations. All the six components therefore cannot be independent. We can select to field
components as an independent components and the remaining four components can be obtained from the Maxwell's
equation.
Since the  - direction is a special direction(direction of the net wave propagation) we choose the longitudinal electric and
magnetic field components (  ,  ) as independent components and derive the transverse components in terms of
the longitudinal components using the Maxwell's equation.
Since the net wave is travelling in a  - direction any field component in the  - direction will be of the type  ,
where  is the phase constant of the net wave propagating along the  - direction.
If we define a parameter  (transverse propagation constant) as
 
we can write transverse electric and magnetic field in term of the longitudinal field components (  ,  ) as
    ----------- (6.28 )
    ----------- (6.29 )
Here  transverse is defined by
    ----------- (6.30 )
in Cartesians co-ordinate system.
 
From the above equations we can make some important observations as follows :
(1)
Transverse fields can exist provided at least one of the longitudinal components ( or ) is non-zero, except when 
= 0. That is, in general there is no transverse electromagnetic wave propagation except when .
(2)
For  we get  implying that the transverse electromagnetic wave can exist in a waveguide if its
propagation constant is same as that of the unbound medium filling the waveguide.
(3)
The fields corresponding to , have electric field transverse to the direction of wave propagation and hence
represent the Transverse electric (TE) wave.
(4)
The fields corresponding to =0 have magnetic field transverse to the direction of wave propagation and hence
represent Transverse magnetic (TM) wave.
(5)
For TM or TE case,  or  respectively is to be non zero, and  has to be non zero. Otherwise the transverse fields
would become infinite. In other words, the TE and TM modes can not have the phase constant same as that of the
unbound medium. The TE and TM modes then essentially have to be dispersive modes i.e., their phase velocity should
vary as a function of frequency.
In Cartesian co-ordinate system we can explicitly write the transverse field component in terms of the longitudinal
components as
 
     ----------- (6.31)
 
     ----------- (6.32)
 
     ----------- (6.33)
 
 
     ----------- (6.34)
 
So, in the analysis of a wave guide first we obtain  or  which is consistent with the boundary conditions and then
subsequently obtain the transverse component using the above equation.
1 2 3 4 5 6
Page 4


 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
   Objective
   In this course you will learn the following
General Approach to Wave Guide Analysis.
Transverse Magnetic Mode.
Boundary conditions for the longitudinal electric field.
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
General Approach to Wave Guide Analysis
In case of parallel wave guide the modal propagation was visualized as super position of multiply reflected plane wave
from the two conducting sheets. This approach although provides better physical understanding of the modal propagation,
becomes algebraically unmanagable for complicated waveguide in structure.
In the following we develop a general framework for analyzing the wave guide structure like a Rectangular Wave Guide.
A rectangular wave guide is a hollow metallic pipe with rectangular cross section. The electro magnetic energy
propagates along the length of pipe. The net wave propagation therefore is along the length of the pipe.
A direction along the length of the pipe is called the Longitudinal direction. Whereas any direction perpendicular to the
wave propagation is called the TRANSVERSE DIRECTION.
Let us choose the co-ordinate system such that the  - axis is along the longitudinal direction.
You can note that in general there are six field components, three for electric field nad three for magnetic field which are
related through Maxwell's equations. All the six components therefore cannot be independent. We can select to field
components as an independent components and the remaining four components can be obtained from the Maxwell's
equation.
Since the  - direction is a special direction(direction of the net wave propagation) we choose the longitudinal electric and
magnetic field components (  ,  ) as independent components and derive the transverse components in terms of
the longitudinal components using the Maxwell's equation.
Since the net wave is travelling in a  - direction any field component in the  - direction will be of the type  ,
where  is the phase constant of the net wave propagating along the  - direction.
If we define a parameter  (transverse propagation constant) as
 
we can write transverse electric and magnetic field in term of the longitudinal field components (  ,  ) as
    ----------- (6.28 )
    ----------- (6.29 )
Here  transverse is defined by
    ----------- (6.30 )
in Cartesians co-ordinate system.
 
From the above equations we can make some important observations as follows :
(1)
Transverse fields can exist provided at least one of the longitudinal components ( or ) is non-zero, except when 
= 0. That is, in general there is no transverse electromagnetic wave propagation except when .
(2)
For  we get  implying that the transverse electromagnetic wave can exist in a waveguide if its
propagation constant is same as that of the unbound medium filling the waveguide.
(3)
The fields corresponding to , have electric field transverse to the direction of wave propagation and hence
represent the Transverse electric (TE) wave.
(4)
The fields corresponding to =0 have magnetic field transverse to the direction of wave propagation and hence
represent Transverse magnetic (TM) wave.
(5)
For TM or TE case,  or  respectively is to be non zero, and  has to be non zero. Otherwise the transverse fields
would become infinite. In other words, the TE and TM modes can not have the phase constant same as that of the
unbound medium. The TE and TM modes then essentially have to be dispersive modes i.e., their phase velocity should
vary as a function of frequency.
In Cartesian co-ordinate system we can explicitly write the transverse field component in terms of the longitudinal
components as
 
     ----------- (6.31)
 
     ----------- (6.32)
 
     ----------- (6.33)
 
 
     ----------- (6.34)
 
So, in the analysis of a wave guide first we obtain  or  which is consistent with the boundary conditions and then
subsequently obtain the transverse component using the above equation.
1 2 3 4 5 6
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
Transverse Magnetic Mode
A rectangular waveguide with cross-section  is shown in the figure below
The walls of the waveguide are made of ideal conductior and the medium filling the waveguide is ideal dielectric.
 
As a convention and the -axis is oriented along the broader dimension of the wave guide, and the -axis is oriented
along the shorter dimension of the waveguide. The -axis is oriented along the length of the waveguide and the waveguide
is assumed to be infinite length.
 
For transverse magnetic mode, we have  and . The transverse fields are therefore represented in terms
of  components only.
 
The wave equation is to be solved for  with appropriate boundary conditions. In Cartesian co-ordinates the wave
equation for  can be written as
 
                     -------- (6.35) 
  
The equation can be solved by the separation of variables i.e by assuming that  is given as
                                                     --------(6.36) 
 
The fields are assumed to be of sinosoidal nature with an angular frequency  .
  
Substituting for  from 6.36 into 6.35, we get
                                                  -------- (6.37)
 
 
 
 
Note that in equation 6.37 the first term is a function of , the second term is a function of  only, the third term is a
function of  only and fourth term is a constant. Since the equation is to be satisfied for every value of  each term in
equation 6.37 must be constant i.e
Page 5


 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
   Objective
   In this course you will learn the following
General Approach to Wave Guide Analysis.
Transverse Magnetic Mode.
Boundary conditions for the longitudinal electric field.
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
General Approach to Wave Guide Analysis
In case of parallel wave guide the modal propagation was visualized as super position of multiply reflected plane wave
from the two conducting sheets. This approach although provides better physical understanding of the modal propagation,
becomes algebraically unmanagable for complicated waveguide in structure.
In the following we develop a general framework for analyzing the wave guide structure like a Rectangular Wave Guide.
A rectangular wave guide is a hollow metallic pipe with rectangular cross section. The electro magnetic energy
propagates along the length of pipe. The net wave propagation therefore is along the length of the pipe.
A direction along the length of the pipe is called the Longitudinal direction. Whereas any direction perpendicular to the
wave propagation is called the TRANSVERSE DIRECTION.
Let us choose the co-ordinate system such that the  - axis is along the longitudinal direction.
You can note that in general there are six field components, three for electric field nad three for magnetic field which are
related through Maxwell's equations. All the six components therefore cannot be independent. We can select to field
components as an independent components and the remaining four components can be obtained from the Maxwell's
equation.
Since the  - direction is a special direction(direction of the net wave propagation) we choose the longitudinal electric and
magnetic field components (  ,  ) as independent components and derive the transverse components in terms of
the longitudinal components using the Maxwell's equation.
Since the net wave is travelling in a  - direction any field component in the  - direction will be of the type  ,
where  is the phase constant of the net wave propagating along the  - direction.
If we define a parameter  (transverse propagation constant) as
 
we can write transverse electric and magnetic field in term of the longitudinal field components (  ,  ) as
    ----------- (6.28 )
    ----------- (6.29 )
Here  transverse is defined by
    ----------- (6.30 )
in Cartesians co-ordinate system.
 
From the above equations we can make some important observations as follows :
(1)
Transverse fields can exist provided at least one of the longitudinal components ( or ) is non-zero, except when 
= 0. That is, in general there is no transverse electromagnetic wave propagation except when .
(2)
For  we get  implying that the transverse electromagnetic wave can exist in a waveguide if its
propagation constant is same as that of the unbound medium filling the waveguide.
(3)
The fields corresponding to , have electric field transverse to the direction of wave propagation and hence
represent the Transverse electric (TE) wave.
(4)
The fields corresponding to =0 have magnetic field transverse to the direction of wave propagation and hence
represent Transverse magnetic (TM) wave.
(5)
For TM or TE case,  or  respectively is to be non zero, and  has to be non zero. Otherwise the transverse fields
would become infinite. In other words, the TE and TM modes can not have the phase constant same as that of the
unbound medium. The TE and TM modes then essentially have to be dispersive modes i.e., their phase velocity should
vary as a function of frequency.
In Cartesian co-ordinate system we can explicitly write the transverse field component in terms of the longitudinal
components as
 
     ----------- (6.31)
 
     ----------- (6.32)
 
     ----------- (6.33)
 
 
     ----------- (6.34)
 
So, in the analysis of a wave guide first we obtain  or  which is consistent with the boundary conditions and then
subsequently obtain the transverse component using the above equation.
1 2 3 4 5 6
 Module 6 : Wave Guides
Lecture 43 : Rectangular Wave Guide and Transverse Magnetic Mode
 
Transverse Magnetic Mode
A rectangular waveguide with cross-section  is shown in the figure below
The walls of the waveguide are made of ideal conductior and the medium filling the waveguide is ideal dielectric.
 
As a convention and the -axis is oriented along the broader dimension of the wave guide, and the -axis is oriented
along the shorter dimension of the waveguide. The -axis is oriented along the length of the waveguide and the waveguide
is assumed to be infinite length.
 
For transverse magnetic mode, we have  and . The transverse fields are therefore represented in terms
of  components only.
 
The wave equation is to be solved for  with appropriate boundary conditions. In Cartesian co-ordinates the wave
equation for  can be written as
 
                     -------- (6.35) 
  
The equation can be solved by the separation of variables i.e by assuming that  is given as
                                                     --------(6.36) 
 
The fields are assumed to be of sinosoidal nature with an angular frequency  .
  
Substituting for  from 6.36 into 6.35, we get
                                                  -------- (6.37)
 
 
 
 
Note that in equation 6.37 the first term is a function of , the second term is a function of  only, the third term is a
function of  only and fourth term is a constant. Since the equation is to be satisfied for every value of  each term in
equation 6.37 must be constant i.e
 
                                                           
 
---------- (6.38)
 
---------- (6.39)
 
---------- (6.40)
 
 and  are real constants.
 
From the physical understanding of reflection of waves from parallel conducting boundaries we expect a standing wave
kind of behaviour in  and  directions and a travelling wave kind of behaviour in  direction. In any case, we expect a
wave phenomenon in  direction which can be properly represented by putting a negative sign infront of the constant 
 ,  and  . Instead of negative sign if the positive sign was used the solutions will have real exponential
functions which would not represent the wave phenomenon.
 
The equations 6.38, 6.39 and 6.40 can be re-written as
                                                                            
 
---------- (6.41)
 
---------- (6.42)
 
---------- (6.43)
 
These equations are identical to the transmission line equations.
 
The solution to equations 6.41, 6.42 and 6.43 can be appropriately written as
 
---------- (6.44)
---------- (6.45)
 
---------- (6.46)
where  are arbitrary constants which are to be evaluated by boundary conditions.
 
If we assume that waveguide is of infinite length, we can take only one travelling wave in -direction. We can
then choose  . Substituting for  from 6.44, 6.45 and 6.46 into equation 6.36 the general solution for 
can be written as
---------- (6.47)
Read More
Offer running on EduRev: Apply code STAYHOME200 to get INR 200 off on our premium plan EduRev Infinity!