Civil Engineering (CE) Exam  >  Civil Engineering (CE) Notes  >  Modes of Propagation and Types of Optical Fibers

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE) PDF Download

Modes of Propagation 
Though optical fiber should support any numbers of rays for propagation practically it is found that it allow only certain restricted number of rays for propagation. The maximum number of rays supported by the fiber is called Modes of propagastion. Modes of propagation can be determined using parameter called V-number.

V-number (Normalised Frequency of the fiber):
An Optical fibre may be characterized by one more parameter called V-number. This determines the Number of modes supported for propagation in the fibre.

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

where “d is the diameter of the core, λ is wavelength, n1 is the refractive index of the core and n2 is the refractive index of the cladding. NA is numerical Aperture. If the fiber is surrounded by a medium of refractive index n0 then

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)
If Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE) , the number of modes supported by fiber can be determined using the formula

Number of Modes ≈ V2 /2

Types of Optical Fibers
Based on R I profile and Core size and Modes of Propagation Optical fibers are classified into 3 types,
(1) Single mode step index fiber.
(2) Multi mode step index fiber.
(3) Graded index multi mode or Grain index fiber.

Single mode step index fiber:
A single mode step index fiber consists of a very fine thin

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

core of uniform RI surrounded by Cladding of RI lower than that of Core. Since there is abrupt change of RI of Core and Cladding at the interface it is called Step index fiber. Since the Core size is small the Numerical aperture is also small. They accept light from laser source. Splicing is difficult. They are used in submarine cables.

Multimode step index fiber:
This is similar to single mode step index fiber with the exception that it has a larger core diameter. The core diameter is very large as compared to wavelength of light transmitted. A typical multimode step index fiber is as shown above. The numerical aperture is large because of large core size. They accept light from both laser as well as from LED. They are used in data links.

Graded index multimode fiber(GRIN fiber):
The multimode fiber, which has concentric layers of RI, is called GRIN fiber. It means

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

the R I of the Core varies with distance from the fiber axis. It has high R I at Center and falls rapidly as radial distance increases from the axis. The R I profile is as shown in fig. In GRIN fibers the acceptance angle and numerical aperture diminishes with radial distance. The light transmission is as shown above. They accept light from both laser as well as from LED. They are used for medium distance communication for example telephone link between central offices.

Attenuation and Fiber losses
An Optical signal passing through a fiber will get progressively reduced. This reduction or attenuation of signal may be defined as the ratio of the optical output power from a fibre of length L to the input optical power. It is expressed in terms of decibel / km.

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

Where P1 → Power of optical signal at launching end (input power)
P2 → Power of optical signal at receiving end (output power)

The attenuation is wavelength dependent and so the wavelength must also be specified.

The attenuation in fibers gives rise to the following three losses
(1) Absorption losses
(2) Geometric Effects
(3) Rayleigh Scattering.

Absorption:
Even very pure glass absorbs light of a specific wavelength. Strong electronic absorption occurs in UV region and vibrational absorption occurs in IR region of wavelength 7 micrometer to 12 micrometer. These losses are attributed due to inherent property of the glass and are called intrinsic absorption. However, this loss is insignificant.

Impurities are major extrinsic source of losses in fiber. Hydroxyl radical ions (OH) and transition metals like Nickel, Chromium, Copper, Manganese etc. have electronic losses near visible range of spectrum. These impurities should be kept as minimum as possible in the fiber. Intrinsic as well as extrinsic losses are found to be minimum at about 1.3 micrometer.

Geometric effects:
These may occur due to manufacturing defects like irregularities in fibre dimensions during drawing process or during coating, cabling or insulation processes.

The microscopic bends are the bends with radii greater than fiber diameter. The micro bends couple light between the various guided modes of the fiber and some of them then leak through the fiber.

Rayleigh Scattering: 
As glass has disordered structure having local microscopic variation in density which may also cause variation in RI. So light traveling through these structures may suffer scattering losses due to Rayleigh ie., scattering α = 1/λ4 . It means Rayleigh scattering sets a lower limit on wavelength that can be transmitted by a glass fibre at 0.8 micrometer below which scattering loss is appreciably high.

Dispersion: 
A pulse launched with a fibre gets attenuated due to losses in fibre. Moreover the incoming pulse also spreads during the transit through the fibre. So a pulse at the output is wider than the pulse at the input i.e., the pulse gets distorted as it moves through the fibre. This distortion of pulse is due to dispersion effects, which is measured in terms nanoseconds per km. There are three phenomena that may contribute towards the distortion effect.
(1) Material dispersion
(2) Wave guide dispersion
(3) Intermodal dispersion.

In optical fibers the Cladding material has uniform RI. But the RI of Core may remain constant or subjected to variation in a particular way. The curve representing the variation of RI with the Radial distance from the axis of the Core is called Refractive index profile. Modes of Propagation is the number paths of light rays along which the waves are in phase inside the fibre. The number of modes, a fibre can support depends on the ratio d/λ where d is the diameter of the core and λ is the wavelength of the wave transmitted.

The document Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE) is a part of Civil Engineering (CE) category.
All you need of Civil Engineering (CE) at this link: Civil Engineering (CE)

Top Courses for Civil Engineering (CE)

FAQs on Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

1. What are the modes of propagation in optical fibers?
Ans. The modes of propagation in optical fibers refer to the different paths that light can travel through the fiber. The two main modes of propagation are the single-mode and multi-mode modes. In single-mode fibers, only one mode of light travels through the core, while in multi-mode fibers, multiple modes of light can travel simultaneously.
2. What is the difference between single-mode and multi-mode fibers?
Ans. The main difference between single-mode and multi-mode fibers lies in the number of modes of light that can propagate through them. Single-mode fibers allow only one mode of light to travel, providing a more focused and direct transmission. On the other hand, multi-mode fibers allow multiple modes of light to propagate simultaneously, which can result in higher dispersion and signal loss.
3. What are the advantages of single-mode fibers over multi-mode fibers?
Ans. Single-mode fibers offer several advantages over multi-mode fibers. They have a higher bandwidth, which means they can transmit data over longer distances without significant signal degradation. Single-mode fibers also have lower dispersion, allowing for clearer and more accurate transmission. Additionally, they are less prone to attenuation, ensuring minimal signal loss.
4. What are the different types of optical fibers?
Ans. There are various types of optical fibers used in different applications. Some common types include single-mode fibers, multi-mode fibers, dispersion-shifted fibers, and plastic optical fibers. Each type has specific characteristics and is suited for specific purposes, such as long-distance communication, local area networks, or industrial applications.
5. What factors should be considered when choosing an optical fiber type?
Ans. When selecting an optical fiber type, several factors should be considered. These include the required bandwidth, distance of transmission, cost, installation requirements, and environmental conditions. Single-mode fibers are suitable for long-distance communication, while multi-mode fibers are more cost-effective for shorter distances. The choice also depends on the specific application and the available infrastructure.
Download as PDF
Explore Courses for Civil Engineering (CE) exam

Top Courses for Civil Engineering (CE)

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

,

Free

,

Objective type Questions

,

Previous Year Questions with Solutions

,

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

,

Sample Paper

,

Extra Questions

,

MCQs

,

study material

,

shortcuts and tricks

,

Important questions

,

Viva Questions

,

Exam

,

ppt

,

past year papers

,

Summary

,

Semester Notes

,

practice quizzes

,

mock tests for examination

,

video lectures

,

pdf

,

Modes of Propagation and Types of Optical Fibers - Civil Engineering (CE)

;