Electrical Engineering (EE) Exam  >  Electrical Engineering (EE) Notes  >  Basic Electrical Technology  >  Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE) PDF Download

Objectives 

  • Meaning of circuit analysis; distinguish between the terms mesh and loop.
  • To provide more general and powerful circuit analysis tool based on Kirchhoff’s voltage law (KVL) only.

Introduction

The Series-parallel reduction technique that we learned in lesson-3 for analyzing DC circuits simplifies every step logically from the preceding step and leads on logically to the next step. Unfortunately, if the circuit is complicated, this method (the simplify and reconstruct) becomes mathematically laborious, time consuming and likely to produce mistake in calculations. In fact, to elevate these difficulties, some methods are available which do not require much thought at all and we need only to follow a well-defined faithful procedure. One most popular technique will be discussed in this lesson is known as ‘mesh or loop’ analysis method that based on the fundamental principles of circuits laws, namely, Ohm’s law and Kirchhoff’s voltage law. Some simple circuit problems will be analyzed by hand calculation to understand the procedure that involve in mesh or loop current analysis.

Meaning of circuit analysis  

The method by which one can determine a variable (either a voltage or a current) of a circuit is called analysis. Basic difference between ‘mesh’ and ‘loop’ is discussed in lesson-3 with an example. A ‘mesh’ is any closed path in a given circuit that does not have any element (or branch) inside it. A mesh has the properties that (i) every node in the closed path is exactly formed with two branches (ii) no other branches are enclosed by the closed path. Meshes can be thought of a resembling window partitions. On the other hand, ‘loop’ is also a closed path but inside the closed path there may be one or more than one branches or elements.

Solution of Electric Circuit Based on Mesh (Loop) Current Method 

Let us consider a simple dc network as shown in Figure 4.1 to find the currents through different branches using Mesh (Loop) current method.  

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Applying KVL around mesh (loop)-1:(note in mesh-1, I1 is known as local current and other mesh currents I2 & I3 are known as foreign currents.) 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)
Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)
Applying KVL around mesh (loop)-2:(similarly in mesh-2, I2 is local current and 11 & I3 are known as foreign currents) 
Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Applying KVL around mesh (loop)-3: 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

** In general, we can write for ith mesh ( for i = 1, 2, .....N)

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)
Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE) simply means to take the algebraic sum of all voltage sources around the ith mesh. 

Rii → means the total self resistance around the ith mesh. 
Rii → means the mutual resistance between the and jth meshes.  

Note: Generally, Rij = Rji (true only for linear bilateral circuits)   

Ii → the unknown mesh currents for the network.

Summarize: 

Step-I: Draw the circuit on a flat surface with no conductor crossovers.
Step-2: Label the mesh currents (Ii) carefully in a clockwise direction.
Step-3: Write the mesh equations by inspecting the circuit (No. of independent mesh (loop) equations=no. of branches (b) - no. of principle nodes (n) + 1). 

Note: 

To analysis, a resistive network containing voltage and current sources using ‘mesh’ equations method the following steps are essential to note: 

  • If possible, convert current source to voltage source.
  • Otherwise, define the voltage across the current source and write the mesh equations as if these source voltages were known. Augment the set of equations with one equation for each current source expressing a known mesh current or difference between two mesh currents.
  • Mesh analysis is valid only for circuits that can be drawn in a two-dimensional plane in such a way that no element crosses over another.

Example-: Find the current through 'ab-branch' (Iab) and voltage (Vcg) across the current source using Mesh-current method.

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Solution: Assume voltage across the current source is v1 (‘c’ is higher potential than ‘g’ (ground potential and assumed as zero potential) and note I2 = -2A (since assigned current direction (I2) is opposite to the source current) 

Loop - 1: (Appling KVL) 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)
Loop - 2: (Appling KVL)
Let us assume the voltage across the current source is  and its top end is assigned with a positive sign. 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Solving equations (4.4) and (4.6), we get  Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Ibg = I1 − I 2 = 1.304 A

- ve sign of current means that the current flows in reverse direction (in our case, the current flows through 4Ω resistor from  ‘c’ to ‘b’ point). From equation (4.5), one can get v1 = 6.27 volt.

Another way: −v1+vbg + vbc = 0 ⇒ v1 = vcg =6.27 volt.

Example-L-4.2 For the circuit shown Figure 4.3 (a) find Vx using the mesh current method. 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)
Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Solution:  One can easily convert the extreme right current source (6 A) into a voltage source. Note that the current source magnitude is 6 A and its internal resistance is 6 Ω . The given circuit is redrawn and shown in Figure 4.3 (c) 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Using the value of I2 = 2A in equation (4.7), we get Vx = 48volt.

Example-L-4.3 Find VR for the circuit shown in figure 4.4 using ‘mesh current method. Calculate the power absorbed or delivered by the sources and all the elements. 

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

Solution: Assume the voltage across the current source is ‘ v ’ and the bottom end of current source is marked as positive sign.  

For loop No. 1: (KVL equation)         

v − (I1− I2) ×100 − I1 ×100 = 0 ⇒ v − 200 I1 + 100 I2 = 0    

It may be noted that from the figure that the current flowing through the 10 resistor (in the middle branch) is10 Ω. More specifically, one can write the following expression 

I1 − I2 = 10 ×10−3  

For loop No. 2: (KVL equation) 
−20− (I2 − I1) ×100 − v − I2 ×100 = 0 ⇒ v + 200 I2 − 100 I1 = − 20   

Solving equations (4.8)-(4.10), one can obtained the loop currents as I=-0.095 = - 95mA (-ve sign indicates that the assigned loop current direction is not correct or in other words loop current (I1) direction is anticlockwise.) and I2 =-0.105 = -105 mA (note, loop current (I2) direction is anticlockwise). Now the voltage across the 100 Ω resistor (extreme right branch) is given by vR = I2 x100 = -0.105x100 =-10.5volt. .This indicates that the resistor terminal (b) adjacent to the voltage source is more positive than the other end of the resistor terminal

(a). From equation (4.8)  and this implies that the ‘top’ end of the current source is more positive than the bottom ‘end’. v =− 8.5volt
 Power delivered by the voltage source = 20 × 0.105 = 2.1W (note that the current is leaving the positive terminal of the voltage source). On the other hand, the power received or absorbed by the current source = 8.5 × 0.01 = 0.085W (since current entering to the positive terminal (top terminal) of the current source). Power absorbed by the all resistance is given 

= (0.105)2 ×100+ (0.095)2 ×100+ (10 ×10−3)2 ×100 = 2.015W .

Further one can note that the power delivered (Pd = 2.1 W) = power absorbed (Pab = 0.085 + 2.015 = 2.1W) = 2.1W

The document Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE) is a part of the Electrical Engineering (EE) Course Basic Electrical Technology.
All you need of Electrical Engineering (EE) at this link: Electrical Engineering (EE)
57 docs|62 tests

Top Courses for Electrical Engineering (EE)

FAQs on Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents - Basic Electrical Technology - Electrical Engineering (EE)

1. What is loop analysis in the context of resistive circuits?
Ans. Loop analysis, also known as Kirchhoff's voltage law (KVL), is a method used to analyze resistive circuits in terms of DC voltages and currents. It is based on the principle that the sum of the voltage drops around any closed loop in a circuit must be equal to the sum of the voltage sources in that loop.
2. How is loop analysis performed in resistive circuits?
Ans. To perform loop analysis in resistive circuits, follow these steps: 1. Identify all the loops in the circuit. 2. Assign a direction for each loop and label the current flowing through it. 3. Apply Kirchhoff's voltage law to each loop by summing up the voltage drops and voltage sources in that loop. 4. Write down the equations for each loop. 5. Solve the simultaneous equations to find the unknown currents or voltages in the circuit.
3. What are the advantages of using loop analysis in resistive circuits?
Ans. Loop analysis offers the following advantages in resistive circuits: 1. It provides a systematic and efficient method for solving complex circuits. 2. It allows for the analysis of circuits with multiple loops and branches. 3. It helps in understanding the distribution of voltages across different elements in the circuit. 4. It enables the determination of unknown currents or voltages in the circuit. 5. It is based on fundamental principles and can be applied to any resistive circuit.
4. Can loop analysis be used for circuits with capacitors and inductors?
Ans. No, loop analysis is specifically designed for resistive circuits. It relies on the assumption that the circuit elements are resistors, which have a linear relationship between voltage and current. Capacitors and inductors, on the other hand, exhibit reactive behavior and their voltage-current relationship is governed by differential equations. To analyze circuits with capacitors and inductors, other methods such as nodal analysis or mesh analysis are used.
5. Are there any limitations or assumptions associated with loop analysis?
Ans. Yes, loop analysis has some limitations and assumptions: 1. It assumes that the circuit consists only of resistors and ideal voltage/current sources. 2. It assumes that the circuit is in a steady-state condition, with no transient behavior. 3. It assumes that the circuit elements obey Ohm's law and have a linear relationship between voltage and current. 4. It assumes that the connections between circuit elements are ideal, with no parasitic effects like stray capacitance or inductance. 5. It may not be suitable for circuits with a large number of loops, as solving simultaneous equations can become complex and time-consuming.
57 docs|62 tests
Download as PDF
Explore Courses for Electrical Engineering (EE) exam

Top Courses for Electrical Engineering (EE)

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

Sample Paper

,

shortcuts and tricks

,

MCQs

,

study material

,

Free

,

Previous Year Questions with Solutions

,

Extra Questions

,

Objective type Questions

,

Semester Notes

,

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

,

Summary

,

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

,

ppt

,

Important questions

,

mock tests for examination

,

Exam

,

practice quizzes

,

video lectures

,

Viva Questions

,

Loop Analysis of Resistive Circuit in the Context of DC Voltages & Currents | Basic Electrical Technology - Electrical Engineering (EE)

,

pdf

,

past year papers

;