Mechanical Engineering Exam  >  Mechanical Engineering Notes  >  Additional Study Material for Mechanical Engineering  >  Thick Cylinders Stresses due To Internal And External Pressures

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering PDF Download

Stresses in thick cylinders

For thick cylinders such as guns, pipes to hydraulic presses, high pressure hydraulic pipes the wall thickness is relatively large and the stress variation across the thickness is also significant. In this situation the approach made in the previous section is not suitable. The problem may be solved by considering an axisymmetry about z-axis and solving the differential equations of stress equilibrium in polar co-ordinates. In general the stress equations of equilibrium without body forces can be given as

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering                   (1)

For axisymmetry about z-axis Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering and this gives 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering                       (2)

In a plane stress situation if the cylinder ends are free to expand σz = 0 and due to uniform radial deformation and symmetry τrz = τθz = τ = 0. The equation of equilibrium reduces to

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

This can be written in the following form:       (3)

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

If we consider a general case with body forces such as centrifugal forces in the case of a rotating cylinder or disc then the equations reduce to

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering (4)

 It is convenient to solve the general equation so that a variety of problems may be solved. Now as shown in figure- 9.2.1.1, the strains εr and εθ may be given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.1.1F- Representation of radial and circumferential strain.

Combining equation (5) and (6) we have

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Now from equation (4) we may write

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineeringand combining this with equation (7) we may arrive at

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering         (8)

For a non-rotating thick cylinder with internal and external pressures pi and po we substitute ω = 0 in equation (8) and this gives

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering         (9)

A typical case is shown in figure- 9.2.1.2. A standard solution for equation (9) is σr = crn where c and n are constants. Substituting this in equation (9) and also combining with equation (3) we have

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering              (10)

where cand c2 are constants.

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering
9.2.1.2F- A thick cylinder with both external and internal pressure

Boundary conditions for a thick cylinder with internal and external pressures pi and po respectively are:

at r = ri σr = -p
and at r = ro σr = -po

The negative signs appear due to the compressive nature of the pressures. This gives

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

The radial stress σr and circumferential stress σθ are now given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering                  (11)

 

It is important to remember that if σθ works out to be positive, it is tensile and if it is negative, it is compressive whereas σr is always compressive irrespective of its sign. Stress distributions for different conditions may be obtained by simply substituting the relevant values in equation (11). For example, if po = 0 i.e. there is no external pressure the radial and circumferential stress reduce to

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering                                           (12)
 

The stress distribution within the cylinder wall is shown in figure- 9.2.1.3.

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.1.3F- Radial and circumferential stress distribution within the cylinder wall when only internal pressure acts.

 

It may be noted that σr + σθ = constant and hence the deformation in z-direction is uniform. This means that the cross-section perpendicular to the cylinder axis remains plane. Hence the deformation in an element cut out by two adjacent cross-sections does not interfere with the adjacent element. Therefore it is justified to assume a condition of plane stress for an element in section 9.2.1.

If pi = 0 i.e. there is no internal pressure the stresses σr and σθ reduce to

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering                             (13)
The stress distributions are shown in figure-9.2.1.4.

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.1.4F- Distribution of radial and circumferential stresses within the cylinder wall when only external pressure acts.

 

Methods of increasing the elastic strength of a thick cylinder by pre-stressing 

In thick walled cylinders subjected to internal pressure only it can be seen from equation (12) that the maximum stresses occur at the inside radius and this can be given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering             Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

This means that as pi increases σθ may exceed yield stress even when p< σyield. Furthermore, it can be shown that for large internal pressures in thick walled cylinders the wall thickness is required to be very large. This is shown schematically in figure 9.2.2.1. This means that the material near the outer edge is not effectively used since the stresses near the outer edge gradually reduce (Refer to figure- 9.2.1.3).

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering
9.2.2.1F- A schematic variation of wall thickness with the internal pressure in a thick walled cylinder.

 

In order to make thick-walled cylinders that resist elastically large internal pressure and make effective use of material at the outer portion of the cylinder the following methods of pre-stressing are used:

1. Shrinking a hollow cylinder over the main cylinder.
2. Multilayered or laminated cylinders.
3. Autofrettage or self hooping.

1. Composite cylinders
An outer cylinder (jacket) with the internal diameter slightly smaller than the outer diameter of the main cylinder is heated and fitted onto the main cylinder. When the assembly cools down to room temperature a composite cylinder is obtained. In this process the main cylinder is subjected to an external pressure leading to a compressive radial stress at the interface. The outer cylinder or the jacket is subjected to an internal pressure leading to a tensile circumferential stress at the inner wall. Under this condition as the internal pressure increases the compression in the inner cylinder is first released and then only the cylinder begins to act in tension. Gun barrels are normally pre-stressed by hooping since very large internal pressures are generated.

Here the main problem is to determine the contact pressure ps. At the contact surface the outer radius rsi of the inner cylinder is slightly larger than the inside diameter rso of the outer cylinder. However for stress calculations we assume that  rso ≌  rsi = rs (say). The inner and outer cylinders are shown in figure- 9.2.2.2.

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical EngineeringThick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.2.2F- Dimensions and the pressures at the contact surface of the internal and outer cylinders.

For the outer cylinder the radial and circumferential stresses at the contact surface may be given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

In order to find the radial displacements of the cylinder walls at the contact we consider that Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering This gives the radial displacement of the inner wall of the outer cylinder as

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Similarly for the inner cylinder the radial and circumferential stresses at the outer wall can be given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

And following the above procedure the radial displacement of the contact surface of the inner cylinder is given by

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

The total interference δ at the contact is therefore given by

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

This gives the contact pressure in terms of the known variables as follows:

 

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering
The combined stress distribution in a shrink fit composite cylinder is made up of stress distribution in the inner and outer cylinders and this is shown in figure-9.2.2.3.

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.2.3F- Combined stress distribution in a composite cylinder.

Residual circumferential stress is maximum at r = ri for the inner cylinder and is given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Residual circumferential stress is maximum at r = rs for the outer cylinder and is given by

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

Stresses due to fluid pressure must be superimposed on this to find the complete stress distribution.

 

2. Multilayered or Laminated cylinder

The laminated cylinders are made by stretching the shells in tension and then welding along a longitudinal seam. This is shown in figure- 9.2.2.4.

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering  Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

9.2.2.4F- Method of construction of multilayered cylinder

 

3. Autofrettage 

In some applications of thick cylinders such as gun barrels no inelastic deformation is permitted. But for some pressure vessel design satisfactory function can be maintained until the inelastic deformation that starts at inner bore spreads completely over the wall thickness. With the increase in fluid pressure yielding would start at the inner bore and then with further increase in fluid pressure yielding would spread outward. If now the pressure is released the outer elastic layer would regain its original size and exert a radial compression on the inner shell and tension on the outer region.

This gives the same effect as that obtained by shrinking a hoop over an inner cylinder. This is known as Self- hooping or Autofrettage. This allows the cylinder to operate at higher fluid pressure. For a given autofrettage fluid pressure a given amount of inelastic deformation is produced and therefore in service the same fluid pressure may be used without causing any additional inelastic deformation.

The document Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering is a part of the Mechanical Engineering Course Additional Study Material for Mechanical Engineering.
All you need of Mechanical Engineering at this link: Mechanical Engineering
1 videos|30 docs|57 tests

Top Courses for Mechanical Engineering

FAQs on Thick Cylinders Stresses due To Internal And External Pressures - Additional Study Material for Mechanical Engineering

1. What is the formula for calculating the stress in a thick cylinder due to internal pressure?
Ans. The formula for calculating the stress in a thick cylinder due to internal pressure is given by the Lame's equation, which is σθ = (P*r)/(2t) where σθ is the hoop stress, P is the internal pressure, r is the radius of the cylinder, and t is the thickness of the cylinder.
2. How is the stress distribution different in a thick cylinder compared to a thin cylinder?
Ans. In a thick cylinder, the stress distribution is non-uniform and varies across the thickness of the cylinder. It is highest at the inner surface (hoop stress) and decreases towards the outer surface. In contrast, a thin cylinder has a uniform stress distribution across its thickness.
3. What is the difference between internal pressure and external pressure in the context of thick cylinders?
Ans. Internal pressure refers to the pressure exerted on the inside of a thick cylinder, usually caused by a fluid or gas contained within it. External pressure, on the other hand, refers to the pressure exerted on the outer surface of the cylinder, which can be due to external environmental factors or additional loads.
4. How does the presence of external pressure affect the stress in a thick cylinder?
Ans. The presence of external pressure in a thick cylinder increases the overall stress levels. The combined effect of internal and external pressures results in higher hoop stress at the inner surface and lower hoop stress at the outer surface. This can potentially lead to structural failure if the stress exceeds the material's yield strength.
5. Can a thick cylinder withstand both internal and external pressures simultaneously?
Ans. Yes, a thick cylinder is designed to withstand both internal and external pressures simultaneously. The thickness of the cylinder is chosen in such a way that it can handle the combined stresses arising from internal and external pressures without exceeding the material's strength limits. Proper design considerations and material selection are crucial to ensure the cylinder's integrity under such conditions.
Explore Courses for Mechanical Engineering exam

Top Courses for Mechanical Engineering

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

Previous Year Questions with Solutions

,

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

,

Exam

,

pdf

,

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

,

shortcuts and tricks

,

past year papers

,

Sample Paper

,

MCQs

,

Semester Notes

,

Extra Questions

,

Thick Cylinders Stresses due To Internal And External Pressures | Additional Study Material for Mechanical Engineering

,

ppt

,

video lectures

,

study material

,

Objective type Questions

,

Important questions

,

Summary

,

Viva Questions

,

practice quizzes

,

mock tests for examination

,

Free

;