Flow Through Pipes | Mechanical Engineering SSC JE (Technical) PDF Download

FLOW THROUGH PIPES

The limiting values of Reynold’s Number corresponding to which flow is Laminar is given by :

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  • Entrance length (Le) - The length of pipe from its entrance upto the point where flow attains fully developed velocity profile and which remains unaltered beyond that known as entrance length.
  • The entrance length required to establish fully developed laminar flow is given by

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  • The entrance length for fully developed turbulent flow is given by

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

Losses in pipe flow

-It is often necessary  to  determine  the  head  loss, h, that occur in a pipe flow so that the energy equation, can be used in the analysis of pipe flow problems.
-The  overall head loss for the pipe  system consists of the head loss due to viscous effects  in the straight pipes, termed the major loss and denoted hL-major.
-The head loss in various pipe components, termed the minor loss and denoted hL-minor.
That is ; hl =  hL-major+ hL-minor
-The  head  loss  designations  of  “major”  and  “minor” do not necessarily reflect the  relative  importance  of  each type of loss.
-For  a  pipe  system  that  contains  many  components and a relatively short length of  pipe, the minor loss may actually be larger than the major loss. 

1. Minor losses 

  • Loss due to sudden expansion This loss is due to eddies in the corner and loss of momentum

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

he= (V12/2g)[1- (A1/A2)2]

V1 = Mean velocity before expansion
V2 = Mean velocity after expansion
A1 = Area of pipe before expansion
A2 = Area of pipe after expansion

  • Loss due to sudden contraction This loss is due to eddies in vena contracta.

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

If value of Cis not given, then the loss due to countraction is taken as 0.5Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

Where, V2 = velocity after contraction
Cc = Coefficient of contraction
A= Area of fluid at vena contracta
A2 = Area of pipe after contraction

  • Exit loss

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)
v → Mean velocity of flow in pipe

  • Entry loss

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  • For sudden expansion, the optimum ratio of diameters of the pipe so that the pressure rise may be maximum

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  • Loss due to gradual expansion

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  hL = KL(V12/2g)[1- (A1/A2)2]

KL depends upon angle of expansion.

  • Loss at pipe fittings

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)
Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

(2) Major losses
Darcy Weisbach equation.

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

f = Friction factor (0.02 to 0.04 for metals)
L = Length of pipe
D = Dia. of pipe
V = Mean velocity of flow

-It  is  valid  for  any  fully  developed, steady, incompressible pipe flow, whether the pipe is horizontal or on hill
-Friction factor for laminar flow is ;
 f=64/Re
-Friction  factor  for  turbulent  flow  is  based  on  Moodychart.
-It is because, in turbulent flow, Reynolds number and relative roughness influence the friction.
-Reynolds number, Re=ρVD/μ
-Relative roughness = ε/D
 (relative roughness is not present in the laminar flow)
-Friction loss in pipe whose end is closed and flow takes place through sides at regular interval

 Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  •  Pipe Connections 
    • Series Connection :

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

(i) Discharge remains constant through all pipes.
(ii) Ignoring secondary losses the total loss of head is equal to the sum of the friction losses in the individual pipes.
Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

  • Parallel Connection

Pipes are said to be in parallel when they are so connected that the flow from a pipe branches or divides into two or more separate pipes and then reunite into a single pipe.
Suppose a main pipe branched at section 1-1 into two pipes of lengths l1 and l2 and diameters d1 and d2 and unite again at a section 2-2 to form a single pipe.
Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

Then the two branch pipes are said to be connected in parallel.
In this arrangement the total discharge Q divides into components Q1 and Q2 along the branch pipes such that –
Q = Q1 + Q2
and in this arrangement the loss of head from section 1-1 to section 2-2 is equal to the loss of head in any one of the branch pipes.
hf = hf1 = hf2 

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

Hence the total discharge Q divides into components Q1 and Q2 satisfying the above equation.

-Power input to pump = g Q(H + hL)/h
-Power output in turbine = g Q(H – hL)h
-Power delivered by a given pipeline is maximum when the flow is such that one third of static head is consumed in pipe friction. Thus efficiency is limited to only 66.66%.

Siphon Action of Pipe 

“In a piping system any part of the pipe is above the hydraulic gradient line it is called a siphon.”In Fig below shows a pipe in which the part BCD is above the hydraulic gradient line. The pressure head at any point along the axis of the pipe is equal to the distance between the HGL and the axis.
Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

It shows that pressure head at points B and D  is zero.The pressure head in the region BCD where pipe is above H.G.L. is negative. The minimum pressure would be at point C(summit point).  If the absolute pressure at point C reache vapour pressure, gases, vapour bubbles are liberated and cavitation occurs.For water,the maximum height of summit above H.G.L. at normal temperature and pressure is 7.8 m.The discharge through a siphon may be calculated as

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

The siphon will start functioning only when it is primed, air is removed from it.

Uses of siphon
1.To carry away water from one reservoir to another reservoir separated by a hill orridge.
2.To take out the liquid from a tank which is not having any outlet.
3.To empty a channel not provided with any outlet sluice. 

Water hammer in pipe 

-Consider a long pipe AB as shown in Fig. below connected at one end to a tank containing water at a height of H from the centre of the pipe. At the other end of the pipe, a valve to regulate the flow of water is  provided. When the valve is completely open, the water is flowing with a velocity, V in the pipe.
-If the valve is suddenly closed, the momentum of the flowing water will be destroyed and consequently a wave of high pressure will be set up. This wave of high pressure will be transmitted along the pipe with a velocity equal to the velocity of sound wave and may create noise called knocking.  Also this wave of high pressure has the  effect of hammering action on the walls of the pipe and hence it is known as water hammer.
Flow Through Pipes | Mechanical Engineering SSC JE (Technical)


-The pressure rise due to water hammer depends upon: (i) the velocity of flow of water in pipe,(ii) length of pipe, (iii) time taken to close the valve, (iv) elastic properties of the material of the pipe. The following cases of water hammer in pipes will be considered:
1.Gradual closure of valve
2.Sudden closure of valve and considering pipe rigid
3.Sudden closure of valve and considering pipe elastic

-The valve closure is gradual if t > (2L/C)
-The valve closure is sudden if t < (2L/C)

where,
L = Length of pipe
t = time in sec.
C = velocity of pressure wave 

(i) Gradual Closure 

In this case the pressure head is given by
  Flow Through Pipes | Mechanical Engineering SSC JE (Technical)where,L = Length of pipeV = Velocity of flow
 t = time in second to close to close the valve.

(ii) Sudden Closure With Rigid Pipe 

  • The pressure head in this case is given by

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)   (Alliev formula)     ... (II)

where,

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)
V = Velocity of pressure wave
K = Bulk modulus of water

 r = density of water.

(iii) Sudden Closure With Elastic Pipe 

  • The pressure head is given by :

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

where,

D = Diameter of pipe
t = Thickness of pipe
E = Modulus of elasticity of pipe material
(In deriving the above equation, the Poisson’s ratio of pipe material is assumed as 0.25.)

The document Flow Through Pipes | Mechanical Engineering SSC JE (Technical) is a part of the Mechanical Engineering Course Mechanical Engineering SSC JE (Technical).
All you need of Mechanical Engineering at this link: Mechanical Engineering
5 videos|103 docs|59 tests

Top Courses for Mechanical Engineering

FAQs on Flow Through Pipes - Mechanical Engineering SSC JE (Technical)

1. What is the definition of flow through pipes in mechanical engineering?
Ans. Flow through pipes in mechanical engineering refers to the movement of fluids, such as liquids or gases, within a closed conduit or pipe. It involves the study of fluid dynamics, pressure drop, and flow rate calculations in order to design efficient and optimal pipe systems for various applications.
2. How is flow rate calculated in pipe systems?
Ans. Flow rate in pipe systems can be calculated using various methods, such as the Bernoulli's equation or the Darcy-Weisbach equation. The most common approach is to use the Darcy-Weisbach equation, which takes into account factors such as pipe diameter, fluid viscosity, and the pressure difference between the inlet and outlet of the pipe.
3. What factors affect the pressure drop in pipe systems?
Ans. Several factors can affect the pressure drop in pipe systems, including the length and diameter of the pipe, the fluid velocity, the type of fluid being transported, and the pipe roughness. Additionally, fittings, valves, and other components in the pipe system can also contribute to pressure losses.
4. How does pipe roughness affect the flow of fluids?
Ans. Pipe roughness refers to the irregularities on the internal surface of the pipe, which can cause frictional resistance and affect the flow of fluids. Higher pipe roughness leads to increased frictional losses and pressure drop in the pipe system. Therefore, it is important to consider the roughness factor when designing pipe systems to ensure efficient flow.
5. What are the different types of pipe flow patterns?
Ans. In pipe systems, there are three main types of flow patterns: laminar flow, transitional flow, and turbulent flow. Laminar flow occurs at low velocities and is characterized by smooth and orderly fluid motion. Transitional flow is an intermediate flow regime between laminar and turbulent flow, while turbulent flow occurs at high velocities and is characterized by chaotic and irregular fluid motion. The type of flow pattern in a pipe system depends on factors such as fluid properties and pipe dimensions.
5 videos|103 docs|59 tests
Download as PDF
Explore Courses for Mechanical Engineering exam

Top Courses for Mechanical Engineering

Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
10M+ students study on EduRev
Related Searches

Semester Notes

,

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

,

Extra Questions

,

past year papers

,

Important questions

,

shortcuts and tricks

,

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

,

mock tests for examination

,

Sample Paper

,

pdf

,

Viva Questions

,

video lectures

,

practice quizzes

,

Exam

,

ppt

,

MCQs

,

Objective type Questions

,

Free

,

Summary

,

Flow Through Pipes | Mechanical Engineering SSC JE (Technical)

,

study material

,

Previous Year Questions with Solutions

;