JEE Exam  >  JEE Notes  >  Physics Main & Advanced  >  Toroid & Solenoid

Toroid & Solenoid - Physics for JEE Main & Advanced PDF Download

9. Toroid : It is on hollow circular tube have windings of conducting wire closely attached to each other circularly on it (as shown below)

Toroid & Solenoid

for ideal Toroid d << R

Magnetic field in Toroid

Let N = Total No. of turns

Now from Ampere's circuital law

Toroid & Solenoid   

B.2πR = μ0 iin = μ0 Ni       

⇒ B = Toroid & Solenoid     

Toroid & Solenoid

n = Toroid & Solenoid = No of turns per unit length

so B = μ0 n i

What is Solenoid?

Let us consider a solenoid, such that its length is large as compared to its radius. Here, the wire is wound in the form of the helix with a very little gap between any two turns. Also, the wires are enameled, thus rendering them insulated from each other. As a result, each turn can be taken as a closed circular loop. The magnetic field thus generated is equivalent to that generated by a circular loop and the total magnetic field generated by the solenoid can be given as the vector sum of force generated by each such turn. The magnetic field lines generated inside a finite solenoid has been shown in the figure below.
Toroid & Solenoid

We can see from the figure that the magnetic field inside the solenoid is uniform in nature and is along the axis of the solenoid. The field at the exterior at any point immediately to the solenoid is very weak and the field lines cannot be seen near the close vicinity. It is important to note that the field inside it is parallel to its axis at every position.


From the Ampere's Law, the magnetic force produced by a solenoid can be given as,
Toroid & Solenoid

Where n is the number of turns of the wire per unit length, I is the current flowing through the wire and the direction is given using the right-hand thumb rule.

10. Infinite Current Carrying sheet

Now from Ampere's loop

Toroid & Solenoid

Toroid & Solenoid

Toroid & Solenoid 

Bl + 0 + Bl + 0 = μ l  
Toroid & Solenoid

B = Toroid & Solenoid

Ex.14 Three identical long solenoids P, Q and R are connected to each other as shown in figure. if the magnetic field at the center of P is 2.0 T, what would be the field at the centre of Q? Assume that the field due to any solenoid is confined within the volume of that solenoid only.

Sol. Toroid & Solenoid

As the solenoids are identical, the currents in Q and R will be the same and will be half the current in P. The magnetic field within a solenoid is given by B = μ0 ni. Hence the field in Q will be equal to the field in R and will be half the field in P i.e., will be 1.0 T

11. Magnetic force on moving charge

When a charge q moves with velocity Toroid & Solenoid, in a magnetic field Toroid & Solenoid, then the magnetic force experienced by moving charge is given by following formula :

Toroid & Solenoid Put q with sign. ...(9)

Toroid & Solenoid : Instantaneous velocity

Toroid & Solenoid : Magnetic field at that point.

11.1 DIFFERENCE BETWEEN MAGNETIC FORCE AND ELECTRIC FORCE

(1) Magentic force is always perpendicular to the field while electric force is collinear with the field.

(2) Magnetic force is velocity dependent, i.e., acts only when the charged particle is in motion while electric force (qE) is independent of the state of rest or motion of the charged particle.

(3) Magentic force does no work when the charged particle is displaced while the electric force does work in displacing the charged particle.

Note :

Toroid & Solenoid

Therefore, Toroid & Solenoid Therefore, power due to magnetic force on a charged particle is zero. (use the formula of power P = Toroid & Solenoidfor its proof)

Since the Toroid & Solenoid so work done by magnetic force is zero in every part of the motion. The magnetic force cannot increase or decrease the speed (or kinetic energy) of a charged particle. Its can only change the direction of velocity.

On a stationary charged particle, magnetic force is zero.

If Toroid & Solenoid, then also magnetic force on charged particle is zero. It moves along a straight line if only magnetic field is acting.

Ex.15 A Charged particle of mass 5 mg and charge q = +2μC has velocity Toroid & Solenoid. Find out the magnetic force on the charged particle and its acceleration at this instant due to magnetic field Toroid & SolenoidToroid & Solenoid and Toroid & Solenoid are in m/s and Wb/m2 respectively.

Sol. Toroid & Solenoid = 2 × 10-6 Toroid & Solenoid

By Newton's Law Toroid & Solenoid

=Toroid & Solenoid

Ex.16 A charged particle has acceleration Toroid & Solenoid in a magnetic field Toroid & Solenoid. Find the value of x.

Sol. Toroid & Solenoid Toroid & Solenoid

Therefore, Toroid & Solenoid

Therefore, Toroid & Solenoid

Therefore, Toroid & Solenoid = 0

⇒ - 6 + 2x = 0 ⇒ x = 3.

12. MOTION OF A CHARGED PARTICLE IN A UNIFORM MAGNETIC FIELD.

12.1 WHEN THE CHARGED PARTICLE IS GIVEN VELOCITY PERPENDICULAR TO THE FIELD

Let a particle of charged q and mass m is moving with a velocity v and enters at right angles to a uniform magnetic field Toroid & Solenoid as shown in figure.

The force on the particle is qvB and this force will always act in a direction perpendicular to v. Hence, the particle will move on a circular path. If the radius of the path is r then

Toroid & Solenoid

Toroid & Solenoid or, r = Toroid & Solenoid ...(10)

Thus, radius of the path is proportional to the momentum mv of the particle and inversely proportional to the magnitude of magnetic field.

Time period : The time period is the time taken by the charged particle to complete one rotation of the circular path which is given by,

T = Toroid & Solenoid = Toroid & Solenoid ...(11)

The time period is independent of the speed v.

Frequency : The frequency is number of revolution of charged particle in one second, which is given by,

Toroid & Solenoid..(12)

and angular frequency = Toroid & Solenoid

Ex 17. A proton (p), a - particle and deuteron (D) are moving in circular paths with same kinetic energies in the same magnetic field. Find the ratio of their radii and time periods. (Neglect interaction between particles).

Sol. R = Toroid & Solenoid

Therefore, Rp : Ra : RD =Toroid & Solenoid

= 1 : 1 : Toroid & Solenoid

T = 2πm/qB

Therefore, Tp : Ta : TToroid & Solenoid : Toroid & Solenoid : Toroid & Solenoid

= 1 : 2 : 2 Ans.

Ex.18 A positive charge particle of charge q, mass m enters into a uniform magnetic field with velocity v as shown in the figure. There is no magnetic field to the left of PQ. Find

 Toroid & Solenoid

(i) time spent,

(ii) distance travelled in the magnetic field

(iii) impulse of magnetic force.

Sol. The particle will move in the field as shown. Angle subtended by the arc at the centre = 2q

(i) Time spent by the charge in magnetic field

wt = q ⇒ Toroid & Solenoid ⇒ t = Toroid & Solenoid

(ii) Distance travelled by the charge in magnetic field : 

= r (2θ) = Toroid & Solenoid 
Toroid & Solenoid

(iii) Impulse = change in momentum of the charge

= (-mv sin θ + mv cos θ Toroid & Solenoid) - (mv sin θ Toroid & Solenoid + mv cos θ ) = -2mv sinθToroid & Solenoid

The document Toroid & Solenoid is a part of the JEE Course Physics for JEE Main & Advanced.
All you need of JEE at this link: JEE

FAQs on Toroid & Solenoid

1. What is a toroid and how does it differ from a solenoid?
Ans. A toroid is a donut-shaped object with a circular cross-section, while a solenoid is a cylindrical coil of wire. The main difference between them is in their shape and the way they are used. Toroids are often used in electronic transformers and inductors, while solenoids are commonly used in electromechanical devices such as valves and relays.
2. How does a toroid work as an inductor?
Ans. A toroid works as an inductor by storing energy in its magnetic field. When a current flows through the wire wound around the toroid, it creates a magnetic field that is concentrated within the toroid's core. This magnetic field stores energy, which can be released when the current is interrupted. The inductance of a toroid depends on factors such as the number of turns of wire and the permeability of the core material.
3. What are some applications of solenoids?
Ans. Solenoids have a wide range of applications due to their ability to convert electrical energy into mechanical motion. Some common uses of solenoids include door locks, automotive starter motors, vending machines, and electric valves. They are also used in various types of electromagnetic relays and actuators.
4. How does a solenoid create a magnetic field?
Ans. A solenoid creates a magnetic field when an electric current flows through the coil of wire. The wire is wound in a helical shape, and the current flowing in one direction creates a magnetic field around each turn of the coil. The magnetic fields of the individual turns align with each other, resulting in a stronger magnetic field in the center of the solenoid.
5. What are some advantages of using toroids and solenoids in electronic systems?
Ans. There are several advantages to using toroids and solenoids in electronic systems. - Toroids offer a high degree of magnetic coupling, making them efficient for use in transformers and inductors. - The donut shape of toroids allows for more compact and space-saving designs compared to other types of inductors. - Solenoids provide precise and controlled linear or rotational motion, making them suitable for various electromechanical applications. - Both toroids and solenoids can be designed to have high inductance values, allowing for effective energy storage and control in electronic circuits.
Explore Courses for JEE exam
Get EduRev Notes directly in your Google search
Related Searches
mock tests for examination, Free, Exam, Semester Notes, Toroid & Solenoid, past year papers, Toroid & Solenoid, shortcuts and tricks, practice quizzes, Viva Questions, Previous Year Questions with Solutions, Important questions, study material, Objective type Questions, pdf , video lectures, Summary, MCQs, Sample Paper, Toroid & Solenoid, ppt, Extra Questions;