Technical Mock Test CE (SSC JE)- 11

The number of bricks required per cubic metre of brick masonry is

Which one of the following types of concrete is most suitable in extreme cold climates?

The specific gravity of commonly available ordinary portland cement is

Which one of the following correctly expresses the split tensile strength of a circular cylinder of
length L and diameter D, subject to a maximum load of P?

The mix design for pavement concrete is based on

Which one of the following is the most preferred wood for high quality and durable furniture ?

The advantage in using plywood is that the

If ‘W’ is the percentage of water required for normal consistency of cement, water to be addedfor determination of initial setting time is

Which one of the following statements is correct?

The shear centre of a section is defined as that point

Match List I with List II and select the correct answer using the codes given below the lists:
 

List I
a. Moment of inertia
b. Elongation
c. neutral axis
d. Top fibre
 

List II
1. Tensile stress
2. Modulus of rupture
3. Zero shear stress
4. Zero longitudinal stress

A thin cylindrical shell of internal diameter D and thickness t is subjected to internal pressure p.
The change in diameter is given by

Which one of the following shear stressN distribution diagrams is correct for cross-bar
section shown in the given figure

The strain energy in a member is proportional to

Strain energy in torsion of a shaft per unit volume is given by (q is shear stress, E —modulus of
Elasticity and G is modulus of rigidity)

Creep of material is a property indicated by

As per the elastic theory of design, the factor of safety is the ratio of

For the simply supported beam shown in the figure given below, at what distance from the
support A, is the shear force zero?

What is the correct sequence of the following metals in the decreasing order of their Poisson’s
ratio?
1. Aluminum
2. Cast iron
3. Steel

Select the correct answer using the code given below :

The moment capacity of section at plastic hinge equals

The number of independent equations to be satisfied for static equilibrium in a space structureis

The material in which large deformation is possible before absolute failure by rupture takesplace, is known as

In a plastic hinge, the actual distribution of strain across the section is essentially as

A correct solution of a statically indeterminate structure as per the energy method

Clapeyron’s theorem is applied to

The number of unknowns to be determined in the stiffness method is equal to

The allowable shear stress in the web of mild steel beams decreases with (where ‘h’ is height and t is thickness)

Racking force on a steel railway bridge is due to

Which one of the following modes of failure is taken care of in plastic design of a steel beam?

The type of stress induced in the foundation bolts fixing a column to its footing is

Which of the following does not describe a weld type?

A plate used for connecting two or more structural, members intersecting each other is termed as

In the context of the ultimate load theory for steel, the stress-strain curve for steel is idealized as

The sum of nodal forces at any yield line intersection in a slab is

In pre-tensioning scheme, pre-stress load is transferred in

The propagation of a shear crack in a prestressed concrete member depends on

Which of the following deformations are important in case of deep beams when compared to flexure alone ?

A structure design should

The failure criteria in the ultimate load method of design is

Partial safety factors for dead load and imposed load combination for limit state of serviceabilityare

In a R. C. beam shear reinforcement should be always in the form of

The anchorage value of a standard U-type book is equivalent to _____ times the diameter of thebar

Which one of the following pressure units represents the LEAST pressure ?

There are four variables, namely, E (volumeN modulus of elasticity), p (pressure per unit area),g (acceleration due to gravity) and ⁰⁰ (viscosity of water). They are associated with mach, Euler,Froude and Reynolds numbers, respectively, in the order.

For laminar flow in a pipe carrying a given discharge, the height of surface roughness is doubled. In such a case, Darcy-Weisbach friction factor will

Match List-I (Name of instrument) with List-II (Variable measured) and select the correct
answer using the codes given below the lists:

 Match List I and List II and select the correct answer using the codes given below the Lists

If the velocity profile in laminar flow is parabolic, then the shear stress profile must be

Match List I with List II and select the correct answer:

For a hydro-electric project with reaction turbine, the draft tube at the exit from the turbine is

As the depth of immersion of a vertical plane surface increases, the location of centre of pressure

The function of an air vessel in a reciprocating pump is to obtain

A fast centrifugal pump impeller has which of the following ?

Mean precipitation over an area is best obtained from gauged amounts by

Water present in an artesian aquifer is usually

In a linear reservoir, the

In the design of storm sewers, “time of concentration” is relevant to determine the

Self purification of running streams may be due to

Which one of the following principal types of reactors is related to trickling filter ?

A garden developed over top of surface water tank is known as

Rainwater of the locality which flows in sewer is called

Which one of the following is not a formula for determining velocity of flow in sewers

Which soil can take maximum dose of sewage ?

Land treatment of sewage is suitable when

Shear failure of soils takes place when

In a Mohr’s diagram, a point above Mohr’s envelope indicates

Minimum centre to centre spacing of friction pilesof diameter (D) as per BIS code is

Rafts resting on sands can be allowed double of the allowable soil pressure when

Ratio of bearing capacity of double Under Reamed (U.R.) pile to that of single UnderReamed pile is nearly

Influence factor for immediate settlement of footing depends on its

A soil has a liquid limit of 40% and plasticity index of 20%. The plastic limit of the soil will be

In the case of stratified soil layers, the best equation that can be adopted for computing the pressure distribution is

A wet, cohesive subgrade is most effectively stabilised by the addition of

Which one of the following soil types is most likely to be subjected to liquefaction underseismic forces?

The correct sequence of plasticity of minerals in soil in an increasing order is

Which one of the following different types of submerged soils is susceptible to liquefaction under earthquake shocks?

A static cone penetration test is usually conducted when the structure is likely to be founded on which of the following ?

For a sandy soil with soil grains spherical in shape and uniform in size, what is the theoretical void ratio?

Which one of the following surveys is required in observations of stars?

Triangulation station selected close to the main station for avoiding intervening obstruction is called

The process of determining the location of the station (on the map) occupied by the plane is called as

Diurnal variation is greater

Which of the following can be used as a map substitute?

Which one of the following is not strictly a method of remote sensing ?

The general requirement in constructing a reinforced concrete road is to place a single layer of reinforcement

For carrying out bituminous patch work during the rainy season, the most suitable binder is

Which one of the following is the purpose of divisional island ?

With addition of lime in soil

Match List I with List II select the correct answer using the code given below the lists:

Which one of the following is not a desirable property of the subgrade soil as a highway material ?

Guage is the distance between _____ of rails of track.

Narrow gauge is adopted where

The first railway train of the world rolled in the year

The length of rails used in broad gauges in India is

Coning of wheels is at

Non-corrosive material applied to rails consist of

On soft formation ballast material preferred is