IOS And Security Device Manager, Networking Quiz

Question 1

Which of the following commands sets the secret password to Cisco?

Accepted Answer

enable secret Cisco

Answer

enable secret password Cisco

Answer

enable secret cisco

Answer

enable password Cisco

Question 2

You type the following command into the router and receive the following output:

Router#show serial 0/0         ^ % Invalid input detected at '^' marker.

Why was this error message displayed?

Accepted Answer

Part of the command is missing.

Answer

You need to be in privileged mode.

Answer

You cannot have a space between serial and 0/0.

Answer

The router does not have a serial0/0 interface.

Question 3

Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?

show version
show protocols
show interfaces
show controllers
show ip interface

Accepted Answer

2, 3 and 5

Answer

1, 2 and 4

Answer

3 and 4 only

Answer

None of the above

Question 4

You type show running-config and get this output:

[output cut] Line console 0     Exec-timeout 1 35     Password BIXPASSWD     Login [output cut]

What do the two numbers following the exec-timeout command mean?

Accepted Answer

If no commands have been typed in 1 minute and 35 seconds, the console connection will be closed.

Answer

If no command has been typed in 35 seconds, the console connection will be closed.

Answer

If no router activity has been detected in 1 hour and 35 minutes, the console will be locked out.

Answer

If you're connected to the router by a Telnet connection, input must be detected within 1 minute and 35 seconds or the connection will be closed.

Question 5

What layer of the OSI model would you assume the problem is in if you type show interface serial 1 and receive the following message? "Serial1 is down, line protocol is down."

Accepted Answer

Physical layer

Answer

Data Link layer

Answer

Network layer

Answer

None. It is a router problem.

Question 6

Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?

Accepted Answer

show interfaces

Answer

show running-config

Answer

show startup-config

Answer

show versions

Question 7

Which of the following commands will configure all the default VTY ports on a router?

Accepted Answer

Router(config)#line vty 0 4

Answer

Router#line vty 0 4

Answer

Router(config-if)#line console 0

Answer

Router(config)#line vty all

Question 8

You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?

Accepted Answer

show interfaces

Answer

show running-config

Answer

show startup-config

Answer

show protocols

Question 9

Which command will delete the contents of NVRAM on a router?

Accepted Answer

erase start

Answer

delete NVRAM

Answer

delete startup-config

Answer

erase NVRAM

Question 10

What command do you type to save the configuration stored in RAM to NVRAM?

Accepted Answer

Router#copy run startup

Answer

Router(config)#copy current to starting

Answer

Router#copy starting to running

Answer

Router(config)#copy running-config startup-config

Question 11

You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

Accepted Answer

There is more than one show command that starts with the letters ru.

Answer

The command requires additional options or parameters.

Answer

There is no show command that starts with ru.

Answer

The command is being executed from the wrong router mode.

Question 12

If you wanted administrators to see a message when logging into the router, which command would you use?

Accepted Answer

banner motd

Answer

message banner motd

Answer

banner message motd

Answer

message motd

Question 13

How many simultaneous Telnet sessions does a Cisco router support by default?

Accepted Answer

5

Answer

2

Answer

3

Answer

4

Question 14

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:

[output cut] Line console 0     Exec-timeout 1 44     Password 7098C0BQR     Login [output cut]

What cause the password to be stored like this?

Accepted Answer

service password-encryption

Answer

encrypt password

Answer

service-password-encryption

Answer

exec-timeout 1 35

Question 15

Which command will show you whether a DTE or a DCE cable is plugged into serial 0?

Accepted Answer

show controllers serial 0

Answer

sh int s0

Answer

sh int serial 0

Answer

show serial 0 controllers

IOS And Security Device Manager, Networking Quiz - Free MCQ Test with solutions

MCQ Practice Test & Solutions: IOS And Security Device Manager, Networking Quiz (15 Questions)

Which of the following commands sets the secret password to Cisco?

You type the following command into the router and receive the following output:
`Router#show serial 0/0 ^ % Invalid input detected at '^' marker.`
Why was this error message displayed?

Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
show version
show protocols
show interfaces
show controllers
show ip interface

You type show running-config and get this output:
`[output cut] Line console 0 Exec-timeout 1 35 Password BIXPASSWD Login [output cut]`
What do the two numbers following the exec-timeout command mean?

What layer of the OSI model would you assume the problem is in if you type show interface serial 1 and receive the following message? "Serial1 is down, line protocol is down."

Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?

Which of the following commands will configure all the default VTY ports on a router?

You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?

Which command will delete the contents of NVRAM on a router?

What command do you type to save the configuration stored in RAM to NVRAM?

You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

If you wanted administrators to see a message when logging into the router, which command would you use?

How many simultaneous Telnet sessions does a Cisco router support by default?

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:
`[output cut] Line console 0 Exec-timeout 1 44 Password 7098C0BQR Login [output cut]`
What cause the password to be stored like this?

Which command will show you whether a DTE or a DCE cable is plugged into serial 0?

Placement Papers - Technical & HR Questions

Placement Papers - Technical & HR Questions

Top Courses for Campus Placement

About this Campus Placement Practice Test

Explore more Campus Placement Study Resources

IOS And Security Device Manager, Networking Quiz - Free MCQ Test with solutions

MCQ Practice Test & Solutions: IOS And Security Device Manager, Networking Quiz (15 Questions)

Which of the following commands sets the secret password to Cisco?

You type the following command into the router and receive the following output:Router#show serial 0/0 ^ % Invalid input detected at '^' marker.Why was this error message displayed?

Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?show versionshow protocolsshow interfacesshow controllersshow ip interface

You type show running-config and get this output:[output cut] Line console 0 Exec-timeout 1 35 Password BIXPASSWD Login [output cut] What do the two numbers following the exec-timeout command mean?

What layer of the OSI model would you assume the problem is in if you type show interface serial 1 and receive the following message? "Serial1 is down, line protocol is down."

Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?

Which of the following commands will configure all the default VTY ports on a router?

You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?

Which command will delete the contents of NVRAM on a router?

What command do you type to save the configuration stored in RAM to NVRAM?

You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

If you wanted administrators to see a message when logging into the router, which command would you use?

How many simultaneous Telnet sessions does a Cisco router support by default?

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:[output cut] Line console 0 Exec-timeout 1 44 Password 7098C0BQR Login [output cut]What cause the password to be stored like this?

Which command will show you whether a DTE or a DCE cable is plugged into serial 0?

Placement Papers - Technical & HR Questions

Placement Papers - Technical & HR Questions

Top Courses for Campus Placement

About this Campus Placement Practice Test

Explore more Campus Placement Study Resources

You type the following command into the router and receive the following output:
`Router#show serial 0/0 ^ % Invalid input detected at '^' marker.`
Why was this error message displayed?

Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
show version
show protocols
show interfaces
show controllers
show ip interface

You type show running-config and get this output:
`[output cut] Line console 0 Exec-timeout 1 35 Password BIXPASSWD Login [output cut]`
What do the two numbers following the exec-timeout command mean?

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:
`[output cut] Line console 0 Exec-timeout 1 44 Password 7098C0BQR Login [output cut]`
What cause the password to be stored like this?