Test: Shear Stress Diagram - Mechanical Engineering MCQ

The determination of the internal forces in the beam is done so as to design the beams as in the application purpose the beams will be subjected to many loads. This will help us to make the beam properly. And also this will ensure that the beams will not break after the loading is done on them. For this another method is the distribution load method.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

The loading acting upward is considered to be positive. This is done as to decrease the time used for the calculations. If the method of sections is being applied at the complex sections for the determination of the unknown forces, much time is required for it. Thus the main motto is to make the calculations easy and make the less use of time.

The couple is the cross product of the force and the perpendicular distance between the forces. And if the division of the both is done than the resulting quantity is the distance only. But care must be taken that the product is the cross product and hence sine angle must be divided too to get the distance.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

As this is done with the help of distributed load method thus when a concentrated load is applied this equation is not valid. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

The loading acting upward is considered to be positive. This is done as to decrease the time used for the calculations. If the method of sections is being applied at the complex sections for the determination of the unknown forces, much time is required for it. Thus the main motto is to make the calculations easy and make the less use of time.

As this is done with the help of distributed load method thus when a couple moment this equation act is not valid. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

Both of them are vector quantities. And both of them can be easily simplified. If taken in the vector form then the task is even easier. Thus it is not necessary for the force or the couple to be vector only, even if the magnitude is taken, the simplification is done in the 2D. Forces are simplified on the basis of the algebra.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

The determination of the internal forces is done by various methods among which the distribution of load method is the one. Also we have method of joints, which is done so as to determine the internal forces which are being developed in the trusses or the frames. This is done as to design them. In this method the loading acting upward is considered to be positive.

The loading acting upward is considered to be positive. This is done as to decrease the time used for the calculations. If the method of sections is being applied at the complex sections for the determination of the unknown forces, much time is required for it. Thus the main motto is to make the calculations easy and make the less use of time.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.

After the application of the force equation of equilibrium to the segment of the beam, we have the above result. This is done on the very small part of the beam. That is the minimal section of the beam is to be considered and then the application of the equilibrium equations are done so as to calculate the final result.