AutoCAD Training Exercises for Beginners - 1 Video Lecture | A complete Guide to AutoCAD (English) - Design Softwares

in this video we are going to perform
some exercises based on what we learn in
the previous tutorial so we are going to
create this object so the length of this
object is total 30 20 25 75 so at first
we have to set the limit so first
command will be giving is limit so we
will directly type first three
characters Li M then press ENTER then
for specified load lip corner we have to
use zero comma zero then press ENTER
then for upper right corner as a with
required a length of 75 so we will be
taking more than that so we will take it
hundred hundred comma and then enter
then we have to go for zoom all command
to apply the limits to the screen then
we will start with line command line
will specify the first point on the
lower left corner then we need a
straight line so we will make doorto or
so on ortho mode on you can do it by a
fit on keyboard just click it so once or
three is on your line will be straight
so give the direction where you want to
you and give the limbs so I want 75
length then this is horizontal line has
been created of 75 length so I want to
go vertical so the vertical length is
again 20 25 35 65 so we will go vertical
and here length of 65 then we have to go
on the left side so take the cursor on
the left side and the length is 25 and
30 so horizontal length is 25 ENTER
press ENTER then go again downward the
vertical length is 30 again enter then
again horizontal is 2015 so again go
horizontal give the length of 20 enter
then go downward give the length of 15
vertical length of 15 then press Enter
then this length will be up to this
point so you can see that the length is
30 you can also track this point you can
you have to take your cursor to that
endpoint and come up come up and just
click so it will automatically take that
length and you can click on the close so
it will close the sketch and it will
stop the line command so in this way
this first exercise has been created
then for star you can sell this exercise
by clicking on this Save button so we
will save it as a x1 then just click on
save and we will suppose keep it as it
is we can start new from here also you
just click on this take a CAD as
template click open so Neutron you
started so the next drawing is this star
object
so again we can work out the limit
suppose we will take this as a 30 20
again 30 20 30 you will take it is as
though thirty twenty thirty that means
on the 30 30 30 90 plus 40 is 130 and we
have to take more than that
so we'll take surface 150 150 so we'll
add first we'll set the limits limits in
lower left corner is zero comma zero
enter then upper right corner is 150
comma 150 enter then boom on you can use
the zoom wall command by keyboard also
just press Z then enter then a then
enter so you need not to go to this
position also so we want to create this
top so this will start from this point
so 20 20 and again here this length is
30 and we will have to work out the
angle so take first line command click
on the line you can also go for L enter
this your first point so you have to
detail point in such a way that you will
get the space for trying the compute
objects Y we will take it here then I
want the lines straight so I will make
the earth on then Direction is downward
so length is 20 again I want to go on
the right side so again length is 20 I
want to draw inclined line so I will
make the ortho of series like inclined
line
in between if you if your objects go out
you can pan by pressing pressing down
the scroll and dragging the mouse upward
so in this way you can pan it or you can
also pan from here by clicking this
button and pressing down the first mouse
button and dragging the mouse to come
out just right click and exit so you
will come out so in this case I will
like to give the length we know length
is 30 so I will give 30 now to give the
angle we have to press the tab button on
the keyboard just I will press the tab
so I will have to give this angle from
x-axis downward angle this one so this
angle I will see in this exercise so he
need from this horizontal line this
angle so this vertical angle I know I
know this angle is 30 from vertical line
that means this angle is 90 so remaining
is 60 so I will give that angle of 60
this is this has been created again here
on this direction again length is 34
angle I have to press the tab again this
angle I have to work out so angle
between these two line is 60 that means
again from vertical this will be 30 so
this angle will come out to be 60 so
this angle will be 60 because this is 60
if we draw a vertical line that means
vertical and this inclined line is 30 so
it will be remaining will be 60 degree
so we will just give a 60 then again we
need a straight line so we can from
keyboard we can press the f8 button I
can give the length of 20 give the
direction and the length again I need
the inclined line again a fit button
give the length then tab now this angle
this angle we have seen this is 30 so we
will give the third angle again on this
side length is 30 then tab again I need
this complete angle so we know that this
angle is 60
that means from horizontal line
this angle is 30 that means the
remaining is 150 total is 180 therefore
remaining on this side is 150 so we'll
give 150 again or throw on for straight
line give the length again also give the
length tab again from this vertical line
we have to go 30 ahead by 30 degree that
means total angle is 120 degree again
length of 30 tab again 120 degree then
our phone vaginal or so again length of
circuit tab now here again I need this
angle to be 30 on this side from this
horizontal line to this inclined line so
it will be remaining will be 150 so I
will give 150 and I will
I can also close by clicking see button
on the keyboard so in this way the
second exercise is completed so this is
e x2 suppose I can start the new
then next exercise is this triangle and
three circles are there so it's us we
will create a triangle again limit this
length is 60 plus 15 plus 10 70 80 85 so
more than that we will take it 120 you
can take any any value it should be more
than the required value so it says we
will create this triangle of 60 length
it is a equilateral triangle so this
angle will be 60 and this angle will be
60 but in AutoCAD it will ask you for
this angle so once it is 60 that means
it will be 120 because total angle is
180 list let's say fedsys limits 0 comma
0 1 20 comma 1 2008 enter a enter then
line source point or thorn effect then
length of 60 then inclining or saw again
length of 60 then angle tab so this
angle is 60 that means the remaining
angle will be 120 then just click on see
for closing the line so this triangle is
created then we have to draw the circles
so circle is 10 10 and 15 radius so for
that you will take the circle command
circle radius give the center point and
use the radius of 10 you can enter to
repeat the command last comma you can
press just enter you need not to go
again to this toolbar again specify a
center point give the radius or you can
click from here also click do the radius
of 10 now how to draw the internal
circle so we can make a construction as
we are in very initial stage we will
just make a construction you will draw
one line from this endpoint to the this
midpoint and this endpoint to this
midpoint just take line end of this and
take it to the midpoint of this line
then just press ENTER to stop the line
command again you can press ENTER to
repeat the line command first point to
the midpoint press ENTER to come out
then take the circle command now the
center will be the intersection of these
two lines click on the intersection now
this circle is touching this horizontal
line so we will just click on though we
do not know the exact radius so just we
will click on the midpoint so in this
way the circle is created we don't need
these two lines so we'll use those lines
using it is gamma rays select both the
lines and just press ENTER on the
keyboard so this object is created then
again next object so the makes object is
this one again limit is 90 plus 20 110
plus 30 140 so we will take 200 comma
200 we will just again take the limit 0
comma 0 200 comma 200 and zoom all Z
enter a enter then in this we will need
a line of 90 lengths and on that end of
those two lines we will create the
circle of 20 30 10 20 red first we will
take the line command give the first
point make it or so on give the length
of 90 enter again you have to press
ENTER to come out then circle Center
Point then radius of 20 again circle
center point and radius of 30 again
circle give Center Point radius obtain
again circle radius enter point give
radius of 20 so in this way this object
has been created one line and four
circles now we need this line to be
tangent to this circle so to create a
tangent we will take the line command if
we take here it is showing me the
quadrant so if you create a line from
the quadrant it will not be a correct
correct
if you zoom here with mouse by scrolling
scroll towards monitor so it will be
going inside so we don't want that so we
will just erase this line by saying II
enter and select the object enter so we
have to create a tangent line so to
create a tangent line now he is showing
quadrant we need a tangent to select
that tangent we have to press shift on
the keyboard and right click on the
mouse right click second button and
select tangent from here now we want
line to be tangent to the circle so
click a on at any point on the circle so
tangent line will be created now I want
this tangent line on this circle also
again shift right click say tangent and
click on the circle to come out press
ENTER again to repeat the line press
ENTER again shift slightly tangent click
on the circle again shift right click
tangent click on the circle and enter if
you don't need this line you can
irritate using various command so in
this way this exercise is also created
so thanks for thanks for joining so we
have created the required exercises
thank you