AutoCAD Floor Plan Tutorial for Beginners - 1 Video Lecture | A complete Guide to AutoCAD (English) - Design Softwares

in this tutorial we will be creating 2d
floor plan so we'll be creating this
floor plan
so the length overall length is here
Olympus so we will be creating it in
meter so our unit is if we take the unit
for checking the unit give UN command
enter so our unit is decimal and
precision level is for decimals of two
for decimals so we will be creating in
meter so our one unit will be one meter
so at first we will create this line so
internal width gives for vent for you
meter and a boy is point three is the
wall thickness is the point three so
total length of this line will be four
point for you plus point 3 plus point
three that means around five point one
so at first we will create this line of
five point one length so before that we
will actually set the limits to suppose
15 15 meter so for that we will give
limits command just type limits enter
then lower left corner will be 0 comma 0
enter upper right corner will be 15
comma 50 enter then gives 0 enter the
inter zoom all crap like the limits then
we have to create this line up 5 point
one meter so take the line command give
the start point click start point
suppose here now I want a straight line
so I will make the ortho mode on click
on that or you can also press the f8
button give the direction and give the
length of five point one press ENTER
again press ENTER to come out so this
line is created if you don't want this
in between so for that you give UCS icon
command enter and choose the no region
option after that we have to create a
wall of 0.3 thickness then a room of 6
meter length again wall again room of 4
point 2 meter length and then again wall
so for this we will use the offset comma
so take off set and give the obser
distance of 0.3 then press enter select
object give the direction and click
again from here we want to create a room
of 6 meter so again select this line
give the direction on the right side and
key in the 6 distance again select
object give the direction click again
select object give the direction so zoom
size is 4.2 enter again next wall select
object give direction and click so in
this way these two 6 and 4.2 with lines
are created then connect the bottom line
and again give a thickness of 0.3 so
choose line then click on the endpoint
of this line to the endpoint of this
line then press ENTER to come out then
offset this again offset
we'll be 0.3 enter select object give
the side and click and press enter so
next will be to cover this again we will
choose a line command in point enter
again opposite distance point 3 is
already there so we'll just press ENTER
select the object give the internal
direction and click and press ENTER to
come out so in this way these two boxes
are ready after that we will create
suppose this line from this point of two
years so this length will be this is
four and point three that means four
point three so we will create one line
of four country then again thickness of
wall thickness that width is three
kitchen width is 3 so we will zoom -
planet we will create a line select the
line give the end point give the
direction upward direction and key in
four point three enter enter to come out
then zoom it and then again use offset
distance is orderly they're just press
enter select object give the direction
on the left side and click again select
this object give the direction on the
left side and the distance is three so
again we will give the distance of three
meter
enter again select object so again wall
will be there of point three give the
direction on left side and click after
that the distance is one point one now
here wall thickness is up so we will
take it 0.15 meter so one point one
point one five again one point two and
point three so we will start with one
point one select object give the
direction one point one enter again
select object give Direction distance
Louie one point 0.15 enter again select
the object give the direction again one
point two is the distance and here wall
is point three again so select give the
direction and click so in this way these
vertical objects are created up to this
line after that bedroom is up again
three meter width
then again wall-e is there and veranda
is up 2.3 so again we will offset by 3
meter so upset is still running so we
just click give the reaction distance of
3 enter select object give Direction
click again select object give 2.3 enter
and again select object give the
direction vector so in this way all
these vertical walls has been created
and connect the upper side choose line
endpoint to endpoint just click there
enter like an offset
by 0.3 inter select the line and click
on the down download side then test to
come out so this overall layout is ready
then next will be we we want to create
the clear the corners so for that you
give the trim command and just press
enter to select all entities at cutting
edges and then remove the unwanted
objects just click on that and those
will be the remote
again here or you can directly use the
crossing window so in this way then here
at the corner if they want like this so
you will trim it
you
and here also on the corner we'll send
this then enter to come out then next
will be to make the door openings so
first door open door will be here so
this is a deed or width is one meter so
at first we will check what is the
length here using the major distance
then just track this point don't click
only track the point to measure the
distance click and measure it is 1.15 so
it is more by 0.15 that means zero seven
five that means we have to keep the half
of the then click exit half of the point
one five year and half of the point one
five year that means that will be zero
zero point zero seven five so we will
just create create one line here just
drag this point don't click just hold up
your cursor for some time and just drag
the mouse on the left side so for this
to be if you for these to be working
properly your this object snap tracking
should be on for that then only it will
work properly if it is not on make it on
then track and now we want a distance of
zero point zero seven five put the
distance and enter so that your line
will start from that point automatically
then we want the line to be
perpendicular to this so we will just
drag this endpoint and come back on the
our place and click then press ENTER so
from here the width is one meter so we
will just again offset
the resistance of one enter click on the
line and click on the side you want the
opposite presenter to come out then trim
enter and click on the unwanted object
enter to come out
so this door opening is created then
next is suppose this door opening so
they are not given this distance how
much should be kept here so we will
assume it as a hundred so again we will
create one line there so zoom it again
line again take the line command then
again track the point don't click just
hold for some time and come down and
give distance of 0.1 hundred mm that is
point one meter then again drag the end
point and come down and click enter the
size of the door here is d1 d1 is 0.9
meter width
so again we will offset by 0.9 enter
click on the downside enter again
trim it trim enter remove this so this
has been also created then next will be
this opening again here they have not
given a any resource so we will take it
one beta so will again o offset it
suppose by one offset by one meter enter
select the line give the side and click
and enter then again trim enter and
remove the unwanted objects
here also you don't go on this enter
seen this way three openings has been
created then next to is this d1 so d1 is
again point nine this both D ones are
point nine so we will just offset this
line by point nine offset point nine
this line from the per side and this
line on the plus enter then we will
again trim so you want to trim complete
line after this we will suppose we will
use these three as the cutting edge we
will use crossing window and here also
these three as cutting edge then press
ENTER and then click on the unwanted
object are you can also use crossing
window enter so these two door openings
are created then next will be here d2 so
again here we will offset by one point
one but so again we will offset it
offset by 1.1 enter this line on down
side click there enter I can offset by
0.15 enter select this line go down
click enter
now here the door size is pointed so
again we will obsolete by point eight
point it enter this line on this side
enter
then we want to extend this line up to
this line so you will use the extend
command extend press enter and click on
this line so it will be extended press
ENTER to come out now trim the again
unwanted objects trim enter we move this
observes then press ENTER to come out
again we will not be needing this line
so we will erase it so that you can give
a enter then select an end so this
toilet is ready then
but for bath again here the length
required is actually two point one so be
upsetting it by two point one so upset
by two point one enter select object
give the side click I can offset this
line by point 15 enter then enter after
that actually this wall is somewhat
ahead so we will just press a stretch it
so at first we will trim it actually
trim enter
then enter to come out and we will
stretch you the crossing window click on
the right side the window should be
green one so you have to click from
right to left and this line should be
moved and these two lines should be
stitched so you have to create a half
window don't cover all the object just
cover the half object enter you the base
point give the direction and give the
distance supposing we want to increase
by point 50 enter so in this way this is
created again we will trim it frame
winter
so this portion is also created then
next will be all these doors opening has
been created so next is this door so
again this is door of one meter so we
will just check the distance measure
distance here distance is less so it is
point 85 so it should be increased by
0.15 so again we will use the stretch
command so again stretch click outside
create a crossing window click you are
taking complete line because we want to
move it and these lines we are taking
half or less than half
click enter give the base point give the
direction we want to go on the left side
by 10.15 winter again this line should
be in the line of this line so again
will be stretch it switch crossing
window enter give the end point then
track this point we want it in this line
don't click now click here then connect
these two lines take the line command
endpoint to endpoint Enter
so here again door opening is created
here also then we don't want this line
we will trim it trim press enter click
enter so in this way door openings are
created then next will be so
to create windows here so we want to
create this window suppose so this
window size is 2 meter so we want to
create this window at the center so
before that actually we will show all
walls are created so we will create one
layer click on this layer properties
then click on this new layer and create
a layer called wall give the name wall
then give the color for the wall suppose
I will take this ok
the line type is continuous only if you
want to give line weight you can give
the line width also so this point 3 is
the line weight then create one more for
window and over also so click on new
layer give the name window then give the
color or window what color you want okay
then line type is continuous I don't
want any line tile line wait so I will
remove the default then next we will
create layer for door so click on this
new layer give the name door
then choose the color okay ten line type
is continuous and default so we will
close this and we will select this
computer wall layout objects then select
here click here and click on wall click
on wall and press escape to come out so
in this wave wall has been created on
the wall layer so right now you we will
stop here and we will continue the door
placement and window placement in the
next tutorial thank you