AutoCAD Floor Plan Tutorial for Beginners - 4 Video Lecture - A complete

in this tutorial we will place the
remaining details such as will Taurus
billionth line
that is which will be traced from here
we lent line then we will place this
hidden roof line which is in line with
this and we place these chargers
charge the part of the window so and we
will place these steps
so these details will be placing in this
tutorial so let's start with suppose P
length line so it is point 100mm outside
so we will create that so for P length
we can create one more layer new layer
we live
you
then we will give some other color to it
and make that layer current in it then
we have to offset this line by 0.1 so we
will say offset now here in offset
setting layer is source that means when
we offset the layer demons as the source
layer so we don't want the source layer
we want the layer current layer as on
our offset should be created on the
current layer and not on the source
layer so you will change their setting
in layer and we will say it current
click on the current so our and we will
just change color for this so we will
check that way it is coming on that
because the color is same for wall and
peeling so we will not understand that
so we'll just take this layer the color
okay
and again offset now here layer is
current so our offset will be created on
the current layer so we will give
distance of point 1 and select wall line
click outside so from all the sides will
create that
just click and click outside so on this
side it is gone like this so here also
we will create one then press ENTER to
come out then these corners can be
connected using fill it command will it
so here right now radius setting is zero
so it will not create arc and it will
only connect the lines so fill it he is
asking for the fill it again and again
so we can make to run the fill it for as
many time as we want just click on this
multiple and so fill it will not close
down and it will continue for as much
time as you want so click on the all the
lines so filling line will be created so
in this way this filling line is created
press ENTER to come out then next is
suppose we will create these steps so we
will take it as a 2:30 so for that also
we will make one more layer that is
steps takes
color flows
and we'll create one line from this
point to this intersection winter to
change the layer of this lines like this
line and click on steps press escape to
come out and make the steps layer
current then offset this line by 0.23
select line offset downward
so three steps has been created then
connect the line from end to end
enter now year two length is hidden if
you see here the pillion line has been
shown in hidden line so for that we will
quickly create one more layer new layer
that is feeling - h4 read on then we
will choose that color for pillion theta
so we want to cut out to 31 same as the
P length so here line type we will
change the line type from continuous
click on this continuous then here
hidden is not available just load click
here in for readin first character is H
so just click edge press H on keyboard
so your done easier okay select ledum
okay then close it then change our now
here this line our complete complete
line so we want only from this point to
this point so we will break it so for
that you can use break at point click on
break at points lick the line give the
point where you want to break I can
break at point select the line click
where you want to break then select
these two lines then from here select
fill in H this is skip to come out so in
this way and to reduce the gap between
these hidden lines give the LTS command
line type scale enter and reduce the gap
point eight enter so we reduces some
what more presenter to repeat the
command 0.6 okay press escape to come
out so in this way that P length line is
created completely and steps are also
created then
because appearances their steps are
there then next is this top-line
roofline so we will take it as 300
distance so point three again same
process we will be doing so
by 0.3 distance here actually we seen
that we offset here two times because
this tool there are two lines so we can
join this line by using join command
here so it will create single line so
select joint select these two lines
enter so single line will be created so
it will be easy top six so you want to
go four point three from wall distance
so from here it will be point two so for
that we will create one more layer so
there's a new layer for roof and the
line is redone so we'll give it H give
the color okay then give the line type
as hidden
okay close it then op set the side line
or we can also up set it in single
stroke by joining the complete line so
it has joined the outside line so it
will create a single polyline so it will
be easy to ops it so we'll just create
joined all of these lines and press
enter so this has created a single
outside line so it will be easy to
opposite in single offset it can be
upsetted so offset give the distance of
point two now here already layer setting
its current so here we will make the
layer roof h and select this outside
line click outside enter so in this way
complete off cities create
- for
hope so roof line here is it has been
connected so we'll connect that line
there
so we'll just take
line from here
or we can stretch it also we will escape
it stretch select crossing window so it
should come inside the window enter then
give the base standard this line and
second point of this one so in this way
this roofline its creator properly then
roof is created then next will be these
Chargers set job for window so for that
also we will create one more layer so
new layer new layer ChaCha
going to give some color okay close it
now for Chaz jog in hidden line is there
so he done has been already
automatically sated because of this roof
refers current and edges created below
it therefore it has already taken they
done line so no need to change it just
close it now
again make the charger layer current
take the line command and how charger
will start at a distance of 100 from
this point on this side so just track
this point go up side and put the
distance of point 1 then make our Thorn
you can press f8 on keyboard to make the
or thorn give the distance of point 6
while here this window was of 1.5 length
so it will be one point seven so we will
give one point seven then again here we
will track this endpoint and click here
press ENTER to come out so in this way
this chair is created
so same Cheju will be here also so we'll
just copy it copy these three lines
enter give base point take it outside
enter then we will rotate it so rotate
select object enter give the base point
make the line vertical and click then
move it then again we will say move
select object enter now we want the
midpoint of this two point so we will
just we can also use shift rightly build
between two points just click on this
two points so it will automatically give
the midpoint make the or thorn press
effect one keyboard and places it place
it here so now midpoint he is showing
here so just drag this midpoint and come
down and click there so in this way this
says is created same way we can create
here also so this is 2 meter length so
we will take again line drag the point
go up side put the distance of point 1
and make or thorn effect press F it Q
the distance of 0.6 again here it will
be 2 point 2 because window is 2 meter
long and again connect here by tracking
the point press ENTER now here it will
be the mirror image of this so we will
just mirror it mirror select object
enter the first point of mirror line or
we can catch the midpoint here so it
will automatically place there will
point here give the second point enter
so in this village such as charges has
been created all all the for the judge
has been created then I think all the
remaining details has been created one
more thing this section line actually so
will create this section line also so
for that we will create one more layer
new layer called section then you use
the color quickly then here we will need
a pen therm line because for section
there are one big line and two small
line one big line again two small line
so that is panthan phantom line so
select here click on this Eden click
load for pan thumb P is the first later
so in keyboard press P then select ok
then thumb ok then close it make the
section line current then create the
section line so here from ventilators
here and here so we will create a
section line take the line track this
midpoint from here it will come up to
here from here it will go here and it
will go down
this escape to come out so in this is
the section line is created then at the
corner triangles has been placed so for
that for creating those triangle you can
use here click on arrow near rectangle
click on polyline then give the number
of sides as three enter
then choose the edge method click here
on edge give the first point give the
second point then here is actually
single color has been filled into it so
from here you can choose hatch and click
solid and click inside and close as
creation so in this way this has been
created so same triangle is required
below also just copy it click on copy
select the object enter give the
following base point so we can place it
at the end of other end then press Enter
so in this way there section line is
also created so all the details has been
created now in leaflet next lecture we
will see how to place the text so we'll
stop here thank you