AutoCAD House Section Drawing Tutorial - 2 Video Lecture - A complete Guide

so in the previous tutorial we have
create the layout created the layout so
we'll put H is H so at first we will
start with this data first we will
create this line so we will create it on
H suppose H take line command create
this endpoint track the midpoint just
order for some time and take the cursor
up and click press ENTER to come out
then for deado we'll take it hatch click
on hatch then click here so we will take
this and see 37 and click inside now it
is England we need it to be vertical so
we will change the angle of that
saengil will be 45 degree the center so
in this way this data is created if you
want it smaller or larger you can adjust
the scale if required so if I reduce the
scale it will get smaller if I increase
the scale it will get larger then close
click on close as creation so in this
way data is created then for slab a
concrete
H is required so from here we will again
click on hatch then click here and take
the concrete a our concrete is there
click inside the edge here we have to
reduce the scale suppose we will make it
point 4 you will have to make it point 1
further we have to reduce it suppose
0.05 so now the hatch is properly
concrete H is properly visible so
concrete H is also here so here is there
and below also it is there and so we
will hatch there also so here it is
required just click inside there and it
is that
so here also it is required so you'll
put all that is there press ENTER to
come out then here coping for coping
also actually that is required so we
will draw that line also
so for creating of that line will just
take line command and connect it line or
we can extend it actually this is skip
extend the center and click on this and
then again we will put there concretize
click on hatch concrete is selected
click inside
you
you
so the hatch is not properly visible so
we'll just descrip and we will delete
this edge here is this s delete click
delete on the keyboard and individually
we will create it so it will be properly
visible so H click and we will adjust
the scale suppose we will make it 0.15
0-3
point zero two
now we click here here and here then
closest creation so the scoping hatch is
also created after that here actually
ventilator is to be shown so it is of
point 6 so we'll create that so we will
create it on window so we will create
one line so this point 2 will track this
endpoint and come down and click if
enter to come out I can enter to repeat
the line so from here it will go for 0.6
enter and we will copy this line copy
select object enter the same point to
this endpoint press escape to come out
so ventilator is created so after that
this double line H is there for wall so
you put that hatch so again click on
hatch click here go up and take this
double line edge NC 32 click inside the
walls then increase the scale suppose 2
2
you
you
and it is still not showing so actually
the angle is 45 so make that angle zero
so it will come into light in actually
reduce the scale 0.5 yes now it is
showing properly close as creation so we
need it on hash layer so select this
edge click on home and click on each
layer and press escape to come out so in
this way this wall has Swindell after
that here for footing one continuous
line one here on line hatch is required
so we'll tail again click on hatch click
here and select here is a NC 133 NC 33
click inside this escape actually we
need it on the hatch we will delete it
make the hash layer current
again hatch and C 33 also the all but
will be there click inside the footings
so scale is perfect angle is all right
so just press ENTER to come out so after
that we will need here gravels so we
will take it again H then go down or
what we can do we can apply this footing
has of footing and we can use my
property so all the scale and all those
things will match with with this edge
then click there press escape but but
still it is looking very larger so just
click on that then reduce the scale
suppose we will make it 0.3 press escape
to come up so gravel is done
so after that here is some sand bed is
there so again hatch
and click here then take signed here a
are signed is there then click here then
reduce the scale suppose point one
reduce further 0.05 yes now it is
looking fine close s creation after that
here is vertical vertical lines are here
so for that we will take again hatch and
from here go so we will take NC 31 click
then legs angles increase the scale
suppose we will make it 1 make the angle
vertical 45 increase the scale so it is
looking fine now click on closest
equation so this as is hatch is also
created so all the hatches has been
placed so this symbol is required for GL
below here so we'll just create it by
line click first point make our table by
pressing a bit and click enter and just
copy this line copy select object into
base point second point make ortho and F
it
winter then mirror it mirror select
object enter first point will be the
same point give the second point press
enter or you can also mix it so move it
select object if you select something by
mistake just hold the shift button and
click on the object enter you the
basement view the second points in this
way you can create a GL Simba when
copied
give the base point enter you the second
point here we want it click press escape
to come out so in this way hatching has
been creator all the lesson is created
so what is remained now is dimension and
leader so that we will do in next
tutorial we'll stop here thank you