AutoCAD 3D House Modeling Tutorial Beginner Basic - 4 Video Lecture - A

in this tutorial we will create steps
for Terrace so here now here this site
is point six wall height is 3 meter and
slab height is 0.5 that means total is
3.75 so 3.75 by 0.15 so it will come to
25 so 13 and 12 steps we want to make it
so first we will see what is the plane
on which you want to make it create the
steps so for that we will click on this
AC isometric so when in SI symmetric
this surfaces front so we'll choose the
front lens front
then we will go in empty space and
suppose we will make the steps layer is
already current so you just create
thirteen steps suppose take line command
give the first point take your cursor in
the line of y-direction and give the
height of point 15
zoom it then in the x-direction 0.23
Oh point fifteen point two three enter
enter then copied copy select object
enter you take the bottom end point and
put it on the top end point maegor thorn
f8 click so six eight ten twelve and we
want one more so we will again copy it
copy select object enter take this point
to this point this script to come out
then connect this by line command again
line click on the bottom end point to
top end point escape to come out then
off set it off set read zero point zero
five 15s click outside escape then here
is a enter select the internal line
enter then draw a horizontal line from
here line take this endpoint take it
outside make it straight we skip enter
again line click the endpoint create it
vertical end up and principal this press
one click give the length of
one meter askew so thirteen has been
created 30 then I don't want this line
so I will it is it is this two lines
enter then there will be a landing so
landing will be of 1 meter length so we
will create one rectangle here rectangle
you the first point take the dimension
option so length is 1 and thickness will
be from this point to this point
and give the side click then press pull
it and give the length up to the skip to
come out then move it most select object
enter take this endpoint connect it to
this end cold here is this rectangle
enter then I want 12 in this direction
so I will just copy this or I can mirror
this also to create it opposite so I
will choose mirror 3d select object
enter then I have to give 3 points
around which I want to mirror so around
this surface I want to mirror so I will
take the 3 point of this surface this
first point second point and third point
and delete so subject no escape so I
don't want one step below I want well
only so I will draw a line here line L
enter take the end point maegor thorn F
it click escape and then press fill this
to cut it this will select object go
outside and click this escape to come
out now move this select object and turf
take this endpoint and put it here at
the same point log midpoint so in this
risk delete so this step says be created
then one meter landing will be needed so
for that again we will we can actually
press full this portion faceful select
object and give the length of one meter
escape to come out so landing is also
ready so you see the steps are created
so know these steps select object
this top enter take this top point at
the base point that we will put it at
the neck or thorn f8 we will align it it
at the mid of this
slap slap point slap midpoint so it has
been properly list and those are not
coming down that means they are exactly
matching so those are properly place
then we will have to create railing here
we will need the railings so for that we
will create suppose one circle again
circle so
we need a top plane so we will skip and
from here select the top plane because
we want to Crystal vertical so you can
give the center point give the radius of
point 0 to 20 mm zoom it and place
bullet faithful
it is not risking so extra date select
object enter give the height of point 75
escape to come out
then know it or copy it copy select
object enter take this quadrant clicks
and copy it here at the mid of this data
point at alternate steps here to copy it
kind copies
you
here we'll go for this midpoint we will
go for this endpoint and again this
midpoint so here it will not be needed
this skip now here it a it has gone
outside so we can move it so we'll just
make this ground layer off so that we
can work properly then choose move
select object enter base point give the
direction like or Thorne f8 so we will
be going inside by radius so point zero
two so now these are properly placed so
we will copy in between also so copy
select object enter give the base point
give the direction inside difference
will be a point for you and one point
five press escape so those are properly
copied and this is also very away so you
will just move it move select object
enter base point second one just hook it
properly escape
so this side are created then we can
copy this to this side also so just copy
select all of them then enter now I
actually I will have to select this
discordant and I will have to put at the
mid of this so those will align properly
so this side is done
then next we'll be here so for that
again we will copy this copy select
object enter take this setup quadrant
and copy it here make orthos effect
copy at alternate positions
we'll find the point again this midpoint
then this end point this may depart
escape so again these are gone or set so
we can move it inside more select object
enter base point make or thorne effect
dew point 0 2 as a distance escape to
come out so those are properly placed
then we have to to create a pipe passing
through all this point we will use 3d
polyline command 3d polyline connect the
sender make or call center point
this lost
an inside make or Thonet fit so we want
to go inside
by distance of 0.5 this script so it
will touch properly then to convert it
into a pipe take the circle command give
the center point give this radius of
point 0 2 then to convert this line and
circle into 3d object to use ship combat
ship select object enter click on this
line so in this way this pipe is created
same way we can create on this side also
3d polyline select the center again this
Center Center
in this last Center last thing cut and
again here inside I want to go back went
five this script so again Circle 0.02
then shape this circle enter this line
click on this line so in this way
railing is ready then I will need a
opening for the yes entry for entry so
for that suppose I will create one line
line from this endpoint and take it
outside so when it shows object snaps
don't take those object snap you can
take it in the empty space enter if you
here actually we made a mistake actually
you was have to connect it from here to
here so that carrier to take then again
line command from this point to this
point enter then press fill it crystal
silicon set go there get the thickness
of points SK then here is this a enter
select object enter so in this way the
steps and drilling has been created so
we will stop here thank you and like
this ground here