AutoCAD Polar Array Command Tutorial Complete - 3D Array; Angle; Fill Angle;

in this tutorial we will learn about
polar area click on arrow near the
rectangular array here is the polar
array click on it then select the object
you want to array then press Enter give
the center point around which you want
to add it I want to array around the
center of this circle so click here it
has created area with six number of
atoms from here you can change the
number of atoms how much you want then
here you can define the angle to fill
suppose I want to fill these number of
atoms in 180 degrees so click here so it
will fill it in 180 degree and if you
want it on the upper side from here you
can change the direction click on the
direction so from here you can reverse
the direction and if you want to define
the angle between two atoms from here
you can define the angle between two
atoms as per that it will create the
array with that angle so I will make it
360 degree then from here you can define
the number of rows I want it to be 3 so
it will go further then here you can
give the gap between the rows and here
is the total length if you want to fit
the number of atoms in total length that
you can specify from here from here you
can keep the area associative that means
it will be connected it can be edited if
you remove this it will be act as a
separate atoms then if you click on this
rotate atoms it will not rotate that and
it will keep the atom as it is if you
want it to be rotated to click on this
rotate atoms so it will rotate the atoms
then close there if you want to edit
that it click again on this any one item
of the array from here you can edit the
array again here is the Edit source
option if you want to make any changes
to the source item suppose I want to
trim it from inside then click on this
edit source select the atom ok then
perform your activity trim enter remove
this item
enter
that modification will be applicable to
every item then to come out click on
this a data array and click on this Save
Changes
in this way you can edit the source I
can click on the item then there is one
more option is replace atom if you want
to replace any one atom with other shape
you can do it using this replace atom
for this we will create one object so
for that some position I need this
ellipse here I want this object to be
elliptical I want this ellipse in the
place of this shape click on the array
then click on replace atom then select
the replacement object enter give the
base point the center point then select
an atom in the area to replace this atom
then press enter and exit in this way
you can place any atom anywhere in the
ID as per your requirement so that is
the replace atom and if you don't want
this replacement or any modification
click on this reset array so it will
bring back the original array and it
will remove all the replaced atoms with
the original atoms then there is this
level option is there using this level
option you can create arrange a
direction in 3d for that we will start
3d click on this 3d modelling then AC
isometric then make it shaded we will
create one reference circle then we will
create ones reference atom suppose I
want it to be cone give the center point
give the bottom radius give the right
why I want to add it this cone on this
circle click on this polar
select the object enter give the center
point the center point and here is the
array and if you want to aerate in the Z
Direction here you can give the number
of levels number ops desired level so it
will create area as per that here you
can give a gap between the levels and if
required you can give the total gap as
for that it will aerate then here in row
there is increment elevation option is
there to see this effect of this we will
create one more area again click on AC
isometric make it shaded then create one
different circle create one cylinder the
radius give the right then make the
polar area click on this folder select
object enter give the center point
around which area to be created is the
number of atoms then here we will give
the rules suppose I want for your routes
in this increment will give the height
of to and escape the roads our increment
by the given distance so in this way you
can use the increment elevation distance
so rows will be shifted by that distance
this one thanks for watching we will
stop here