Potential Energy of a Spring Video Lecture | Physics for Airmen Group X - Airforce X Y / Indian Navy SSR

Welcome back.
So we have this green spring
here, and let's see,
there's a wall here.
This connected to the wall.
And let's say that this is where
the spring is naturally.
So if I were not to push on the
spring, it would stretch
all the way out here.
But in this situation, I pushed
on the spring, so it
has a displacement
of x to the left.
And we'll just worry about
magnitude, so we won't worry
too much about direction.
So what I want to do is think
a little bit-- well, first I
want to graph how much force
I've applied at different
points as I compress
this spring.
And then I want to use that
graph to maybe figure out how
much work we did in compressing
the spring.
So let's look at-- I know I'm
compressing to the left.
Maybe I should compress to the
right, so that you can-- well,
we're just worrying about the
magnitude of the x-axis.
Let's draw a little
graph here.
That's my y-axis, x-axis.
So this axis is how much I've
compressed it, x, and then
this axis, the y-axis, is how
much force I have to apply.
So when the spring was initially
all the way out
here, to compress it a little
bit, how much force
do I have to apply?
Well, this was its natural
state, right?
And we know from-- well, Hooke's
Law told us that the
restorative force-- I'll write
a little r down here-- is
equal to negative K, where K is
the spring constant, times
the displacement, right?
That's the restorative force,
so that's the force that the
spring applies to whoever's
pushing on it.
The force to compress it is just
the same thing, but it's
going in the same direction
as the x.
If I'm moving the spring, if I'm
compressing the spring to
the left, then the force I'm
applying is also to the left.
So I'll call that the force
of compression.
The force of compression
is going to be
equal to K times x.
And when the spring is
compressed and not
accelerating in either
direction, the force of
compression is going
to be equal to
the restorative force.
So what I want to do here is
plot the force of compression
with respect to x.
And I should have drawn it the
other way, but I think you
understand that x is increasing
to the left in my
example, right?
This is where x is equal
to 0 right here.
And say, this might be x is
equal to 10 because we've
compressed it by 10 meters.
So let's see how much
force we've applied.
So when x is 0, which is right
here, how much force do we
need to apply to compress
the spring?
Well, if we give zero force, the
spring won't move, but if
we just give a little, little
bit of force, if we just give
infinitesimal, super-small
amount of force, we'll
compress the spring just
a little bit, right?
Because at that point, the force
of compression is going
to be pretty much zero.
So when the spring is barely
compressed, we're going to
apply a little, little bit of
force, so almost at zero.
To displace the spring zero,
we apply zero force.
To displace the spring a little
bit, we have to apply a
little bit more force.
To displace soon. the spring 1
meter, so if this is say, 1
meter, how much force
will we have to
apply to keep it there?
So let's say if this is
1 meter, the force of
compression is going to
be K times 1, so it's
just going to be K.
And realize, you didn't apply
zero and then apply K force.
You keep applying a little
bit more force.
Every time you compress the
spring a little bit, it takes
a little bit more force to
compress it a little bit more.
So to compress it 1 meters,
you need to apply K.
And to get it there, you have to
keep increasing the amount
of force you apply.
At 2 meters, you would've been
up to 2K, et cetera.
I think you see a
line is forming.
Let me draw that line.
The line looks something
like that.
And so this is how much force
you need to apply as a
function of the displacement of
the spring from its natural
rest state, right?
And here I have positive x going
to the right, but in
this case, positive
x is to the left.
I'm just measuring its
actual displacement.
I'm not worried too much about
direction right now.
So I just want you to think
a little bit about what's
happening here.
You just have to slowly keep
on-- you could apply a very
large force initially.
If you apply a very large force
initially, the spring
will actually accelerate much
faster, because you're
applying a much larger force
than its restorative force,
and so it might accelerate and
then it'll spring back, and
actually, we'll do a little
example of that.
But really, just to displace the
spring a certain distance,
you have to just gradually
increase the force, just so
that you offset the
restorative force.
Hopefully, that makes sense,
and you understand that the
force just increases
proportionally as a function
of the distance, and
that's just because
this is a linear equation.
And what's the slope of this?
Well, slope is rise
over run, right?
So if I run 1, this is
1, what's my rise?
It's K.
So the slope of this
graph is K.
So using this graph, let's
figure out how much work we
need to do to compress
this spring.
I don't know, let's
say this is x0.
So x is where it's the
general variable.
X0 is a particular
value for x.
That could be 10 or whatever.
Let's see how much
work we need.
So what's the definition
of work?
Work is equal to the force
in the direction of your
displacement times the
displacement, right?
So let's see how much
we've displaced.
So when we go from zero
to here, we've
displaced this much.
And what was the force
of the displacement?
Well, the force was gradually
increasing the entire time, so
the force is going to be be
roughly about that big.
I'm approximating.
And I'll show you that you
actually have to approximate.
So the force is kind of that
square right there.
And then to displace the next
little distance-- that's not
bright enough-- my force is
going to increase a little
bit, right?
So this is the force, this
is the distance.
So if you you see, the work I'm
doing is actually going to
be the area under the
curve, each of
these rectangles, right?
Because the height of the
rectangle is the force I'm
applying and the width is
the distance, right?
So the work is just going to
be the sum of all of these
rectangles.
And the rectangles I drew are
just kind of approximations,
because they don't get
right under the line.
You have to keep making the
rectangle smaller, smaller,
smaller, and smaller, and just
sum up more and more and more
rectangles, right?
And actually I'm touching on
integral calculus right now.
But if you don't know
integral calculus,
don't worry about it.
But the bottom line is the work
we're doing-- hopefully I
showed you-- is just going to
be the area under this line.
So the work I'm doing to
displace the spring x meters
is the area from here to here.
And what's that area?
Well, this is a triangle, so we
just need to know the base,
the height, and multiply
it times 1/2, right?
That's just the area
of a triangle.
So what's the base?
So this is just x0.
What's the height?
Well, we know the slope is K, so
this height is going to be
x0 times K.
So this point right here
is the point x0, and
then x0 times K.
And so what's the area under the
curve, which is the total
work I did to compress
the spring x0 meters?
Well, it's the base, x0, times
the height, x0, times K.
And then, of course, multiply by
1/2, because we're dealing
with a triangle, right?
So that equals 1/2K
x0 squared.
And for those of you who know
calculus, that, of course, is
the same thing as the
integral of Kx dx.
And that should make sense.
Each of these are little dx's.
But I don't want to go too
much into calculus now.
It'll confuse people.
So that's the total work
necessary to compress the
spring by distance of x0.
Or if we set a distance
of x, you can just get
rid of this 0 here.
And why is that useful?
Because the work necessary to
compress the spring that much
is also how much potential
energy there is
stored in the spring.
So if I told you that I had a
spring and its spring constant
is 10, and I compressed it 5
meters, so x is equal to 5
meters, at the time that it's
compressed, how much potential
energy is in that spring?
We can just say the potential
energy is equal to 1/2K times
x squared equals 1/2.
K is 10 times 25, and
that equals 125.
And, of course, work and
potential energy
are measured in joules.
So this is really what you
just have to memorize.
Or hopefully you don't
memorize it.
Hopefully, you understand where
I got it, and that's why
I spent 10 minutes doing it.
But this is how much work is
necessary to compress the
spring to that point and how
much potential energy is
stored once it is compressed
to that point, or actually
stretched that much.
We've been compressing,
but you can
also stretch the spring.
If you know that, then we can
start doing some problems with
potential energy in springs,
which I will
do in the next video.
See