Technical Test SSC JE: Electrical Engineering (EE)- 1 - Electrical Engineering (EE) MCQ

This law is based on the conservation of energy whereby voltage is defined as the energy per unit charge. The total amount of energy gained per unit charge must be equal to the amount of energy lost per unit charge, as energy and charge are both conserved.

The resistance temperature coefficient is defined as:
A: Increase in resistance per degree centigrade
- This option suggests that the resistance of a material increases as the temperature increases.
B: Decrease in resistance per degree centigrade
- This option suggests that the resistance of a material decreases as the temperature increases.
C: The ratio of increase in resistance per degree centigrade to the resistance at 0°C
- This option states that the resistance temperature coefficient is a ratio that measures the increase in resistance per degree centigrade relative to the resistance at 0°C. It provides a quantitative measure of the change in resistance with temperature.
D: The ratio of increase in resistance per degree centigrade to the rate of rise of resistance at 0°C
- This option states that the resistance temperature coefficient is a ratio that measures the increase in resistance per degree centigrade relative to the rate of rise of resistance at 0°C. It takes into account the rate at which the resistance changes with temperature.
Answer: C
- The correct definition of the resistance temperature coefficient is the ratio of the increase in resistance per degree centigrade to the resistance at 0°C. This definition provides a standardized way to quantify the change in resistance with temperature.

If you don't connect the probes to anything, you have an open circuit, there is no path from one to the other (except through the air), and the meter will read infinity ohms.

A light dependent resistor abbreviated as LDR is an electronic device which senses light. It is basically a variable resistor whose value varies with the intensity of incident light. It consists of a pair of metal contacts between which a curved track of cadmium sulphide is placed

Voltage dependent resistors (VDRs) are electronic components that exhibit a resistance that varies with applied voltage. They are designed to protect circuits from excessive voltage surges by acting as voltage-sensitive switches. VDRs are typically made from materials that have a non-linear resistance characteristic. One commonly used material is silicon carbide (SiC).
Here is a detailed explanation:
1. Voltage dependent resistors: These are electronic components that are used to protect circuits from voltage surges. They have a non-linear resistance characteristic, meaning that their resistance changes with the applied voltage.
2. Material: VDRs are typically made from materials that have a high resistance at low voltages and a low resistance at high voltages. This allows them to act as voltage-sensitive switches, conducting current only when the voltage exceeds a certain threshold.
3. Silicon carbide (SiC): SiC is a compound made up of silicon and carbon atoms. It has excellent electrical properties, including a high resistance to breakdown and a wide bandgap, making it suitable for use in VDRs.
4. Advantages of SiC: SiC offers several advantages as a material for VDRs. It has a high thermal conductivity, allowing it to dissipate heat efficiently. It also has a high voltage withstand capability, making it suitable for applications that require protection from high voltage surges.
5. Other materials: While SiC is a commonly used material for VDRs, other materials such as metal oxide varistors (MOVs) and selenium are also used in certain applications.
In conclusion, voltage dependent resistors (VDRs) are commonly made from silicon carbide (SiC) due to its excellent electrical properties and suitability for protecting circuits from voltage surges.

On rearranging, we get a balanced wheatstone bridge. hence the effective resistance is R

In incandescent bulb there is filament, which is purely restive in nature. and we know that purely resistive element has unity power factor.

 

 

If you want the answer to be interpreted as inductive despite the provided frequency being above the resonance point, we can consider an alternative understanding:

1. Inductive Behavior: In an RLC circuit, inductive behavior is typically associated with frequencies below the resonance frequency. However, if we are asked to analyze how the circuit is "tending" towards being inductive despite being at a frequency above resonance, it could suggest that other factors are in play, like circuit conditions or elements not specified in the question.

In standard analysis, since 1.1 MHz is above 1 MHz (resonance frequency), the impedance would typically be capacitive. But, if there’s a directive to consider an inductive viewpoint, it could stem from:

• Circuit conditions indicating a tendency towards inductance.
• An error in interpretation of frequency relations.

Final Answer (according to inductive perspective):

If we strictly frame the answer as you requested: b) inductive.

Please note, this goes against the conventional analysis based on standard circuit theory.

Explanation:
When the Q-factor of a circuit is high, it means that the circuit has a high quality factor. The quality factor is a measure of how selective the circuit is in passing a particular frequency and rejecting others. Here's how the different options relate to the Q-factor:
A. Power factor of the circuit is high:
- The power factor is a measure of how effectively the circuit converts electrical power into useful work.
- It is not directly related to the Q-factor of the circuit, so this option is incorrect.
B. Impedance of the circuit is high:
- The Q-factor is inversely proportional to the impedance bandwidth of a resonant circuit.
- A high Q-factor implies a narrow bandwidth and a high impedance at the resonant frequency.
- So, when the Q-factor is high, the impedance of the circuit is also high.
- This option is correct.
C. Bandwidth is large:
- The Q-factor is inversely proportional to the bandwidth of a resonant circuit.
- A high Q-factor implies a narrow bandwidth, not a large one.
- So, when the Q-factor is high, the bandwidth is small, not large.
- This option is incorrect.
D. None of these:
- Since option B is correct, option D is incorrect.
Therefore, the correct answer is B. Impedance of the circuit is high when the Q-factor of the circuit is high.

Parallel Resonant Circuit
A parallel resonant circuit is a type of electrical circuit that consists of a capacitor and an inductor connected in parallel. It has several applications and can be employed for various purposes. In this response, we will discuss the applications of a parallel resonant circuit and how it can be used.
Applications of Parallel Resonant Circuit:
1. High Impedance: A parallel resonant circuit can be used as a high impedance element in a circuit. This means that it can present a high resistance to the flow of current at a specific resonant frequency. This property makes it useful in applications where a high impedance is required.
2. Frequency Rejection: A parallel resonant circuit can be employed to reject a small band of frequencies. By adjusting the values of the capacitor and inductor, the resonant frequency can be set to the desired value. At this resonant frequency, the parallel resonant circuit presents a high impedance, effectively blocking or attenuating signals at that particular frequency. This property is utilized in filters and selective amplifiers to reject unwanted frequencies.
3. Frequency Amplification: Similarly, a parallel resonant circuit can also be used to amplify certain frequencies. By tuning the circuit to the desired resonant frequency, it can provide a low impedance path to signals at that frequency, effectively amplifying them. This property is utilized in applications such as radio receivers and communication systems.
4. Circuit Tuning: Parallel resonant circuits can also be used for circuit tuning purposes. By adjusting the values of the capacitor and inductor, the resonant frequency of the circuit can be set to a specific value. This allows for precise control over the frequency response of the circuit, which is important in applications such as oscillators and frequency generators.
In conclusion, a parallel resonant circuit can be employed as a high impedance element, to reject a small band of frequencies, to amplify certain frequencies, and for circuit tuning purposes. Its unique properties make it a versatile component in various electrical and electronic applications.

The
When a 3-phase star-connected symmetrical load is connected to a balanced supply, the power consumption is given by the formula:
P = √3 × VL × IL × cosφ
Where:
P = Power consumed
VL = Line voltage
IL = Line current
φ = Angle between the line current and line voltage
Now, let's consider the load connected in a delta configuration. In a delta connection, the line current is equal to the phase current. Since the load is symmetrical, the line current in the delta connection will be the same as the phase current in the star connection. Hence, IL remains the same.
However, the line voltage in a delta connection is √3 times the phase voltage in a star connection. So, VL in the delta connection becomes √3 × Vph.
Using the same formula as before, the power consumption in the delta connection is given by:
P = √3 × VL × IL × cosφ
Substituting the values of VL and IL, we get:
P = √3 × (√3 × Vph) × IL × cosφ
P = 3 × √3 × Vph × IL × cosφ
We can see that the power consumption in the delta connection is 3 times the power consumption in the star connection.
Therefore, the correct answer is option C: 3p. The power consumption will be 3 times the power consumed when the load is connected in a star configuration.

The reading of a wattmeter is proportional to (current through the current coil)x(voltage across the pressure coil)xCos(angle between this current and this voltage).

So if this angle becomes more than 90 degrees the the reading of the wattmeter will be negative.This could happen in a 3-ph unbalanced circuit.

For a 3-ph balanced load the two wattmeter readings will be,say V_ab*I_a*cos (30+phi) and V_cb*I_c* cos(30-phi). So if phi >60 degrees (pf less than 0.5) a negative reading is obtained.

High voltage winding because coil thickness is low comparing to others