NEET Exam  >  NEET Tests  >  Topic-wise MCQ Tests for NEET  >  Case Based Questions Test: Alternating Current - NEET MCQ

Case Based Questions Test: Alternating Current - NEET MCQ


Test Description

15 Questions MCQ Test Topic-wise MCQ Tests for NEET - Case Based Questions Test: Alternating Current

Case Based Questions Test: Alternating Current for NEET 2024 is part of Topic-wise MCQ Tests for NEET preparation. The Case Based Questions Test: Alternating Current questions and answers have been prepared according to the NEET exam syllabus.The Case Based Questions Test: Alternating Current MCQs are made for NEET 2024 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Case Based Questions Test: Alternating Current below.
Solutions of Case Based Questions Test: Alternating Current questions in English are available as part of our Topic-wise MCQ Tests for NEET for NEET & Case Based Questions Test: Alternating Current solutions in Hindi for Topic-wise MCQ Tests for NEET course. Download more important topics, notes, lectures and mock test series for NEET Exam by signing up for free. Attempt Case Based Questions Test: Alternating Current | 15 questions in 30 minutes | Mock test for NEET preparation | Free important questions MCQ to study Topic-wise MCQ Tests for NEET for NEET Exam | Download free PDF with solutions
Case Based Questions Test: Alternating Current - Question 1

Read the following text and answer the following questions on the basis of the same:

Tuning a radio set: In essence the simplest tuned radio frequency receiver is a simple crystal set. Desired frequency is tuned by a tuned coil / capacitor combination, and then the signal is presented to a simple crystal or diode detector where the amplitude modulated signal, is demodulated. This is then passed straight to the headphones or speaker. In radio set there is an LC oscillator comprising of a variable capacitor (or sometimes a variable coupling coil), with a knob on the front panel to tune the receiver. Capacitor used in old radio sets is gang capacitor. It consists of two sets of parallel circular plates one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance. Air gap between plates acts as dielectric. The capacitor has to be tuned in tandem corresponding to the frequency of a station so that the LC combination of the radio set resonates at the frequency of the desired station.

When capacitive reactance (XC) is equal to the inductive reactance (XL), then the resonance occurs and the resonant frequency is given by ω0 = 1/√LC

current amplitude becomes maximum at the resonant frequency. It is important to note that resonance phenomenon is exhibited by a circuit only if both L and C are present in the circuit. Only then do the voltages across L and C cancel each other (both being out of phase) and the Current amplitude is Vm/R the total source voltage appearing across R. This means that we cannot have resonance in a RL or RC circuit.

Name the phenomenon involved in tuning a radio set to a particular radio station.

Detailed Solution for Case Based Questions Test: Alternating Current - Question 1
Phenomenon involved in tuning a radio set to a particular radio station is resonance. The capacitor has to be tuned in tandem corresponding to the frequency of a station. So, that the LC combination of the radio set resonates at the frequency of the desired station.
Case Based Questions Test: Alternating Current - Question 2

Read the following text and answer the following questions on the basis of the same: Tuning a radio set: In essence the simplest tuned radio frequency receiver is a simple crystal set. Desired frequency is tuned by a tuned coil / capacitor combination, and then the signal is presented to a simple crystal or diode detector where the amplitude modulated signal, is demodulated. This is then passed straight to the headphones or speaker. In radio set there is an LC oscillator comprising of a variable capacitor (or sometimes a variable coupling coil), with a knob on the front panel to tune the receiver. Capacitor used in old radio sets is gang capacitor. It consists of two sets of parallel circular plates one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance. Air gap between plates acts as dielectric. The capacitor has to be tuned in tandem corresponding to the frequency of a station so that the LC combination of the radio set resonates at the frequency of the desired station.

When capacitive reactance (XC) is equal to the inductive reactance (XL), then the resonance occurs and the resonant frequency is given by ω0 = 1/√LC

current amplitude becomes maximum at the resonant frequency. It is important to note that resonance phenomenon is exhibited by a circuit only if both L and C are present in the circuit. Only then do the voltages across L and C cancel each other (both being out of phase) and the Current amplitude is Vm/R the total source voltage appearing across R. This means that we cannot have resonance in a RL or RC circuit.

Resonance frequency is equal to:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 2
The resonant frequency is given by ω0 = 1/√LC
1 Crore+ students have signed up on EduRev. Have you? Download the App
Case Based Questions Test: Alternating Current - Question 3

Read the following text and answer the following questions on the basis of the same: Tuning a radio set: In essence the simplest tuned radio frequency receiver is a simple crystal set. Desired frequency is tuned by a tuned coil / capacitor combination, and then the signal is presented to a simple crystal or diode detector where the amplitude modulated signal, is demodulated. This is then passed straight to the headphones or speaker. In radio set there is an LC oscillator comprising of a variable capacitor (or sometimes a variable coupling coil), with a knob on the front panel to tune the receiver. Capacitor used in old radio sets is gang capacitor. It consists of two sets of parallel circular plates one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance. Air gap between plates acts as dielectric. The capacitor has to be tuned in tandem corresponding to the frequency of a station so that the LC combination of the radio set resonates at the frequency of the desired station.

When capacitive reactance (XC) is equal to the inductive reactance (XL), then the resonance occurs and the resonant frequency is given by ω0 = 1/√LC

current amplitude becomes maximum at the resonant frequency. It is important to note that resonance phenomenon is exhibited by a circuit only if both L and C are present in the circuit. Only then do the voltages across L and C cancel each other (both being out of phase) and the Current amplitude is Vm/R the total source voltage appearing across R. This means that we cannot have resonance in a RL or RC circuit.

Capacitor used in radio set for tuning is a:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 3
Capacitor used in old radio is a parallel plate capacitor. It consists of two sets of parallel circular plates , one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance.
Case Based Questions Test: Alternating Current - Question 4

Read the following text and answer the following questions on the basis of the same:

At power plant, a transformer increases the voltage of generated power by thousands of volts so that it can be sent of long distances through high-voltage transmission power lines. Transmission lines are bundles of wires that carry electric power from power plants to distant substations. At substations, transformers lower the voltage of incoming power to make it acceptable for high volume delivery to nearby end-users. Electricity is sent at extremely high voltage because it limits so-called line losses. Very good conductors of electricity also offer some resistance and this resistance becomes considerable over long distances causing considerable loss.

At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high current becomes low and the loss is minimized. Another option of minimizing loss is the use of wires of superconducting material. Super-conducting materials are capable of conducting without resistance, they must be kept extremely cold, nearly absolute zero, and this requirement makes standard superconducting materials impractical to use. However, recent advances in superconducting materials have decreased cooling requirements. In Germany recently 1 km of superconducting cable have been installed connecting the generating station and the destination. It has eliminated the line loss and the cable is capable of sending five times more electricity than conventional cable. Using superconducting cables Germany has also get rid of the need of costly transformers. Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing, which has cooling fins or radiators similar to heat exchangers on the outside. Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety). Fire point is the temperature at which the oil flashes and continuously burns. This must be very high for the chosen oil (not less than 200° C).

Which of the following statement is true for long distance transmission of electricity?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 4
At power plant, a step-up transformer increases the voltage of generated power by thousands of volts, so that it can be sent of long distances through high-voltage transmission power lines. At substations, step-down transformers lower the voltage of incoming power to make it acceptable for high-volume delivery to nearby end-users.
Case Based Questions Test: Alternating Current - Question 5

Read the following text and answer the following questions on the basis of the same: At power plant, a transformer increases the voltage of generated power by thousands of volts so that it can be sent of long distances through high-voltage transmission power lines. Transmission lines are bundles of wires that carry electric power from power plants to distant substations. At substations, transformers lower the voltage of incoming power to make it acceptable for high volume delivery to nearby end-users. Electricity is sent at extremely high voltage because it limits so-called line losses. Very good conductors of electricity also offer some resistance and this resistance becomes considerable over long distances causing considerable loss.

At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high current becomes low and the loss is minimized. Another option of minimizing loss is the use of wires of superconducting material. Super-conducting materials are capable of conducting without resistance, they must be kept extremely cold, nearly absolute zero, and this requirement makes standard superconducting materials impractical to use. However, recent advances in superconducting materials have decreased cooling requirements. In Germany recently 1 km of superconducting cable have been installed connecting the generating station and the destination. It has eliminated the line loss and the cable is capable of sending five times more electricity than conventional cable. Using superconducting cables Germany has also get rid of the need of costly transformers. Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing, which has cooling fins or radiators similar to heat exchangers on the outside. Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety). Fire point is the temperature at which the oil flashes and continuously burns. This must be very high for the chosen oil (not less than 200° C).

Why does stepping up voltages reduce power loss?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 5
At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high, current becomes low and the loss is minimized.
Case Based Questions Test: Alternating Current - Question 6

Read the following text and answer the following questions on the basis of the same: At power plant, a transformer increases the voltage of generated power by thousands of volts so that it can be sent of long distances through high-voltage transmission power lines. Transmission lines are bundles of wires that carry electric power from power plants to distant substations. At substations, transformers lower the voltage of incoming power to make it acceptable for high volume delivery to nearby end-users. Electricity is sent at extremely high voltage because it limits so-called line losses. Very good conductors of electricity also offer some resistance and this resistance becomes considerable over long distances causing considerable loss.

At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high current becomes low and the loss is minimized. Another option of minimizing loss is the use of wires of superconducting material. Super-conducting materials are capable of conducting without resistance, they must be kept extremely cold, nearly absolute zero, and this requirement makes standard superconducting materials impractical to use. However, recent advances in superconducting materials have decreased cooling requirements. In Germany recently 1 km of superconducting cable have been installed connecting the generating station and the destination. It has eliminated the line loss and the cable is capable of sending five times more electricity than conventional cable. Using superconducting cables Germany has also get rid of the need of costly transformers. Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing, which has cooling fins or radiators similar to heat exchangers on the outside. Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety). Fire point is the temperature at which the oil flashes and continuously burns. This must be very high for the chosen oil (not less than 200° C).

Flush point of an oil is

Detailed Solution for Case Based Questions Test: Alternating Current - Question 6
Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety).
Case Based Questions Test: Alternating Current - Question 7

Read the following text and answer the following questions on the basis of the same:

Losses of transformer

There are 4 types of losses in a transformer: Core loss, Ohmic loss, Stray load loss and dielectric loss.

(1) Core loss Core loss has two components - hysteresis loss and eddy current loss. These together are called no-load losses of a transformer and are calculated by open circuit test.

(a) Hysteresis loss: This loss mainly depends on the core material used in the transformer. To reduce this loss, the high-grade core material can be used. CRGO- Cold rolled grain oriented Si steel is commonly used for this purpose.

(b) Eddy current loss: This loss can be reduced by designing the core using slight laminations. These losses are present even when no load is connected. So, these are also known as no-load loss.

(2) Copper Loss Copper losses occur because of the Ohmic resistance in the windings of the transformer. If the currents in primary and secondary windings of the transformer are I1 and I2, and if the resistances of these windings are R1 & R2 then the copper losses that occurred in the windings are I12R1 & I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.

(3) Stray Loss These types of losses in a transformer occur because of the occurrence of the leakage flux. As compared with copper and iron losses, the percentage of stray losses are less, so these losses can be neglected.

(4) Dielectric Loss This loss mainly occurs within the oil of the transformer. Oil is an insulating material. Once the oil quality in the transformer deteriorates then the transformer’s efficiency is affected. Efficiency of a Transformer It is the ratio of output power and input power. Efficiency = Output Power / Input Power. The transformer is a highly efficient device which ranges between 95% – 98.5%.

What is the relationship among core loss, hysteresis loss and eddy current loss?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 7
Hysteresis loss is caused due to molecular friction in a ferromagnetic material, under alternating magnetic field. Eddy current loss us caused due to the induction of eddy current in the core and conductors held in magnetic field. Hysteresis loss occurs in the core of an electric machine.
Case Based Questions Test: Alternating Current - Question 8

Read the following text and answer the following questions on the basis of the same:

Losses of transformer

There are 4 types of losses in a transformer: Core loss, Ohmic loss, Stray load loss and dielectric loss.

(1) Core loss Core loss has two components - hysteresis loss and eddy current loss. These together are called no-load losses of a transformer and are calculated by open circuit test.

(a) Hysteresis loss: This loss mainly depends on the core material used in the transformer. To reduce this loss, the high-grade core material can be used. CRGO- Cold rolled grain oriented Si steel is commonly used for this purpose.

(b) Eddy current loss: This loss can be reduced by designing the core using slight laminations. These losses are present even when no load is connected. So, these are also known as no-load loss.

(2) Copper Loss Copper losses occur because of the Ohmic resistance in the windings of the transformer. If the currents in primary and secondary windings of the transformer are I1 and I2, and if the resistances of these windings are R1 & R2 then the copper losses that occurred in the windings are I12R1 & I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.

(3) Stray Loss These types of losses in a transformer occur because of the occurrence of the leakage flux. As compared with copper and iron losses, the percentage of stray losses are less, so these losses can be neglected.

(4) Dielectric Loss This loss mainly occurs within the oil of the transformer. Oil is an insulating material. Once the oil quality in the transformer deteriorates then the transformer’s efficiency is affected. Efficiency of a Transformer It is the ratio of output power and input power. Efficiency = Output Power / Input Power. The transformer is a highly efficient device which ranges between 95% – 98.5%.

Which of the following losses in transformer is also known as variable loss?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 8
If the currents in primary and secondary windings of the transformer are I1 and I2 respectively and the resistances of these windings are R1 and R2 then the copper losses that occurred in the windings are I12R1 and I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.
Case Based Questions Test: Alternating Current - Question 9

Read the following text and answer the following questions on the basis of the same:

Losses of transformer

There are 4 types of losses in a transformer: Core loss, Ohmic loss, Stray load loss and dielectric loss.

(1) Core loss Core loss has two components - hysteresis loss and eddy current loss. These together are called no-load losses of a transformer and are calculated by open circuit test.

(a) Hysteresis loss: This loss mainly depends on the core material used in the transformer. To reduce this loss, the high-grade core material can be used. CRGO- Cold rolled grain oriented Si steel is commonly used for this purpose.

(b) Eddy current loss: This loss can be reduced by designing the core using slight laminations. These losses are present even when no load is connected. So, these are also known as no-load loss.

(2) Copper Loss Copper losses occur because of the Ohmic resistance in the windings of the transformer. If the currents in primary and secondary windings of the transformer are I1 and I2, and if the resistances of these windings are R1 & R2 then the copper losses that occurred in the windings are I12R1 & I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.

(3) Stray Loss These types of losses in a transformer occur because of the occurrence of the leakage flux. As compared with copper and iron losses, the percentage of stray losses are less, so these losses can be neglected.

(4) Dielectric Loss This loss mainly occurs within the oil of the transformer. Oil is an insulating material. Once the oil quality in the transformer deteriorates then the transformer’s efficiency is affected. Efficiency of a Transformer It is the ratio of output power and input power. Efficiency = Output Power / Input Power. The transformer is a highly efficient device which ranges between 95% – 98.5%.

Specify the range of transformer efficiency.

Detailed Solution for Case Based Questions Test: Alternating Current - Question 9
95-98%
Case Based Questions Test: Alternating Current - Question 10

Read the following text and answer the following questions on the basis of the same:

Tuning a radio set: In essence the simplest tuned radio frequency receiver is a simple crystal set. Desired frequency is tuned by a tuned coil / capacitor combination, and then the signal is presented to a simple crystal or diode detector where the amplitude modulated signal, is demodulated. This is then passed straight to the headphones or speaker. In radio set there is an LC oscillator comprising of a variable capacitor (or sometimes a variable coupling coil), with a knob on the front panel to tune the receiver. Capacitor used in old radio sets is gang capacitor. It consists of two sets of parallel circular plates one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance. Air gap between plates acts as dielectric. The capacitor has to be tuned in tandem corresponding to the frequency of a station so that the LC combination of the radio set resonates at the frequency of the desired station.

When capacitive reactance (XC) is equal to the inductive reactance (XL), then the resonance occurs and the resonant frequency is given by ω0 = 1/√LC

current amplitude becomes maximum at the resonant frequency. It is important to note that resonance phenomenon is exhibited by a circuit only if both L and C are present in the circuit. Only then do the voltages across L and C cancel each other (both being out of phase) and the Current amplitude is Vm/R the total source voltage appearing across R. This means that we cannot have resonance in a RL or RC circuit.

Resonance may occur in:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 10
A simple radio receiver is a simple crystal set with a coil and capacitor combination. Desired frequency is tuned by tuning the coil - capacitor combination. Tuning means to make capacitive reactance (XC) equal to the inductive reactance (XL), so that the resonance occurs.
Case Based Questions Test: Alternating Current - Question 11

Read the following text and answer the following questions on the basis of the same: Tuning a radio set: In essence the simplest tuned radio frequency receiver is a simple crystal set. Desired frequency is tuned by a tuned coil / capacitor combination, and then the signal is presented to a simple crystal or diode detector where the amplitude modulated signal, is demodulated. This is then passed straight to the headphones or speaker. In radio set there is an LC oscillator comprising of a variable capacitor (or sometimes a variable coupling coil), with a knob on the front panel to tune the receiver. Capacitor used in old radio sets is gang capacitor. It consists of two sets of parallel circular plates one of which can rotate manually by means of a knob. The rotation causes overlapping areas of plates to change, thus changing its capacitance. Air gap between plates acts as dielectric. The capacitor has to be tuned in tandem corresponding to the frequency of a station so that the LC combination of the radio set resonates at the frequency of the desired station.

When capacitive reactance (XC) is equal to the inductive reactance (XL), then the resonance occurs and the resonant frequency is given by ω0 = 1/√LC

current amplitude becomes maximum at the resonant frequency. It is important to note that resonance phenomenon is exhibited by a circuit only if both L and C are present in the circuit. Only then do the voltages across L and C cancel each other (both being out of phase) and the Current amplitude is Vm/R the total source voltage appearing across R. This means that we cannot have resonance in a RL or RC circuit.

Resonance occurs only when:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 11
At resonance, capacitive reactance (XC) is equal to the inductive reactance (XL). Circuit is totally resistive and the current amplitude becomes maximum.
Case Based Questions Test: Alternating Current - Question 12

Read the following text and answer the following questions on the basis of the same: At power plant, a transformer increases the voltage of generated power by thousands of volts so that it can be sent of long distances through high-voltage transmission power lines. Transmission lines are bundles of wires that carry electric power from power plants to distant substations. At substations, transformers lower the voltage of incoming power to make it acceptable for high volume delivery to nearby end-users. Electricity is sent at extremely high voltage because it limits so-called line losses. Very good conductors of electricity also offer some resistance and this resistance becomes considerable over long distances causing considerable loss.

At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high current becomes low and the loss is minimized. Another option of minimizing loss is the use of wires of superconducting material. Super-conducting materials are capable of conducting without resistance, they must be kept extremely cold, nearly absolute zero, and this requirement makes standard superconducting materials impractical to use. However, recent advances in superconducting materials have decreased cooling requirements. In Germany recently 1 km of superconducting cable have been installed connecting the generating station and the destination. It has eliminated the line loss and the cable is capable of sending five times more electricity than conventional cable. Using superconducting cables Germany has also get rid of the need of costly transformers. Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing, which has cooling fins or radiators similar to heat exchangers on the outside. Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety). Fire point is the temperature at which the oil flashes and continuously burns. This must be very high for the chosen oil (not less than 200° C).

Superconducting transmission line has the following advantages:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 12
Super-conducting materials are capable of conducting without resistance. So, this eliminates the line loss and the cable is capable of sending more electricity than conventional cable. Using super-conducting cables, one can get rid of the need of costly transformers.
Case Based Questions Test: Alternating Current - Question 13

Read the following text and answer the following questions on the basis of the same:

At power plant, a transformer increases the voltage of generated power by thousands of volts so that it can be sent of long distances through high-voltage transmission power lines. Transmission lines are bundles of wires that carry electric power from power plants to distant substations. At substations, transformers lower the voltage of incoming power to make it acceptable for high volume delivery to nearby end-users. Electricity is sent at extremely high voltage because it limits so-called line losses. Very good conductors of electricity also offer some resistance and this resistance becomes considerable over long distances causing considerable loss.

At generating station, normally voltage is stepped up to around thousands of volts. Power losses increase with the square of current. Therefore, keeping voltage high current becomes low and the loss is minimized. Another option of minimizing loss is the use of wires of superconducting material. Super-conducting materials are capable of conducting without resistance, they must be kept extremely cold, nearly absolute zero, and this requirement makes standard superconducting materials impractical to use. However, recent advances in superconducting materials have decreased cooling requirements. In Germany recently 1 km of superconducting cable have been installed connecting the generating station and the destination. It has eliminated the line loss and the cable is capable of sending five times more electricity than conventional cable. Using superconducting cables Germany has also get rid of the need of costly transformers. Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing, which has cooling fins or radiators similar to heat exchangers on the outside. Flush point is a very important parameter of transformer oil. Flashpoint of an oil is the temperature at which the oil ignites spontaneously. This must be as high as possible (not less than 160° C from the point of safety). Fire point is the temperature at which the oil flashes and continuously burns. This must be very high for the chosen oil (not less than 200° C).

Oil transfers heat from transformer winding by the process of:

Detailed Solution for Case Based Questions Test: Alternating Current - Question 13
Transformers generate waste heat when they are in operation and oil is the coolant of choice. It transfers the heat through convection to the transformer housing.
Case Based Questions Test: Alternating Current - Question 14

Read the following text and answer the following questions on the basis of the same:

Losses of transformer

There are 4 types of losses in a transformer: Core loss, Ohmic loss, Stray load loss and dielectric loss.

(1) Core loss Core loss has two components - hysteresis loss and eddy current loss. These together are called no-load losses of a transformer and are calculated by open circuit test.

(a) Hysteresis loss: This loss mainly depends on the core material used in the transformer. To reduce this loss, the high-grade core material can be used. CRGO- Cold rolled grain oriented Si steel is commonly used for this purpose.

(b) Eddy current loss: This loss can be reduced by designing the core using slight laminations. These losses are present even when no load is connected. So, these are also known as no-load loss.

(2) Copper Loss Copper losses occur because of the Ohmic resistance in the windings of the transformer. If the currents in primary and secondary windings of the transformer are I1 and I2, and if the resistances of these windings are R1 & R2 then the copper losses that occurred in the windings are I12R1 & I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.

(3) Stray Loss These types of losses in a transformer occur because of the occurrence of the leakage flux. As compared with copper and iron losses, the percentage of stray losses are less, so these losses can be neglected.

(4) Dielectric Loss This loss mainly occurs within the oil of the transformer. Oil is an insulating material. Once the oil quality in the transformer deteriorates then the transformer’s efficiency is affected. Efficiency of a Transformer It is the ratio of output power and input power. Efficiency = Output Power / Input Power. The transformer is a highly efficient device which ranges between 95% – 98.5%.

Which of the following losses in transformer is also known as no-load loss?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 14
Core loss is present even when no load is connected. So, these are also known as no-load loss.
Case Based Questions Test: Alternating Current - Question 15

Read the following text and answer the following questions on the basis of the same:

Losses of transformer

There are 4 types of losses in a transformer: Core loss, Ohmic loss, Stray load loss and dielectric loss.

(1) Core loss Core loss has two components - hysteresis loss and eddy current loss. These together are called no-load losses of a transformer and are calculated by open circuit test.

(a) Hysteresis loss: This loss mainly depends on the core material used in the transformer. To reduce this loss, the high-grade core material can be used. CRGO- Cold rolled grain oriented Si steel is commonly used for this purpose.

(b) Eddy current loss: This loss can be reduced by designing the core using slight laminations. These losses are present even when no load is connected. So, these are also known as no-load loss.

(2) Copper Loss Copper losses occur because of the Ohmic resistance in the windings of the transformer. If the currents in primary and secondary windings of the transformer are I1 and I2, and if the resistances of these windings are R1 & R2 then the copper losses that occurred in the windings are I12R1 & I22R2 respectively. So, the entire copper loss will be I12R1 + I22R2. This loss is also called variable or ohmic losses because this loss changes based on the load.

(3) Stray Loss These types of losses in a transformer occur because of the occurrence of the leakage flux. As compared with copper and iron losses, the percentage of stray losses are less, so these losses can be neglected.

(4) Dielectric Loss This loss mainly occurs within the oil of the transformer. Oil is an insulating material. Once the oil quality in the transformer deteriorates then the transformer’s efficiency is affected. Efficiency of a Transformer It is the ratio of output power and input power. Efficiency = Output Power / Input Power. The transformer is a highly efficient device which ranges between 95% – 98.5%.

How hysteresis loss can be reduced?

Detailed Solution for Case Based Questions Test: Alternating Current - Question 15
Hysteresis losses can be reduced by using material that has less area of the hysteresis loop. Hence, high grade or silica steel can be used for designing the core within a transformer because it has extremely less area of the hysteresis loop.
9 docs|1272 tests
Information about Case Based Questions Test: Alternating Current Page
In this test you can find the Exam questions for Case Based Questions Test: Alternating Current solved & explained in the simplest way possible. Besides giving Questions and answers for Case Based Questions Test: Alternating Current, EduRev gives you an ample number of Online tests for practice

Top Courses for NEET

Download as PDF

Top Courses for NEET