Test: Polar Plot - 1 - Electronics and Communication Engineering (ECE) MCQ

Given transfer function
(it is Lead compensator)
Magnitude of the transfer function will be

Phase of the transfer function will be

At ω = 0 
Magnitude M₁ = 1 and phase ϕ₁ = 0° 
At ω = ∞ 
Magnitude M₂ = 10 and phase ϕ₂ = 0° 
At ω = 2
Magnitude M₃ = 2.19 and phase ϕ₃ = 52.12° 
The polar plot considering the above magnitude and phase values will be

Zero is nearer to the imaginary axis than the pole, hence the plot will move in a clockwise direction.

Gain Margin:

• The gain margin is a factor by which the gain of a stable system is allowed to increase before the system reaches the verge of instability.
• It is also defined as the reciprocal of the gain at which the phase angle becomes 1800.
• The frequency at which the phase angle is 1800 is called the phase crossover frequency (ωpc). 

Mathematically,
∠G(jω)H(jω) = -180º
If  |G(jω)H(jω)| = a, at ω = ω_pc 
Then Gain margin,
  
Phase Margin:

• It is the amount of additional phase lag (at gain crossover frequency) that is required to bring the system to the verge of instability.
• The frequency at which |G(jω)H(jω|, the magnitude of the open-loop transfer function is unity is called gain crossover frequency (ωpc).

At ω_pc, |G(jω)H(jω| = 1
if, ∠G(jω)H(jω) = ϕ at ω = ω_gc
Then, P.M. = 180 + ϕ
Analysis:

For stable systems,
|G(jω_pc)H(jω_pc| < 1, and  
∠G(jω_gc)H(jω_gc) > -180
so that, gain margin and phase margin both are positive 
which is possible when ω_gc < ω_pc  
For marginally stable systems,
ω_gc = ω_pc
Hence option (b) is the correct answer.

Note: For stable systems having two or more gain crossover frequencies, the phase margin is measured at the highest gain crossover frequency.

Polar plot:

• The Polar plot is a plot, which can be drawn between the magnitude and the phase angle of G(jω)H(jω) by varying ω from zero to ∞.
• The calculation of frequency response is tedious, and it does not indicate the impact of individual components of open-loop transfer function.
• Another disadvantage of this plot is that it cannot tell how many poles are in right side of the complex plane.
• To overcome this disadvantage, magnitude is plotted by varying frequency from that is known as the Nyquist plot.
• It has no limitation in portraying the frequency response of a system.

Therefore, Statement (I) is false but Statement (II) is true.

Polar plot:
The polar plot is a plot, that is drawn between the magnitude and the phase angle of G(jω) by varying ω from zero 0 to ∞.
Given,

∠G(jω) = -90° - tan^-1(ωT₁) 

Nyquist plot:
Nyquist plots are an extension of polar plots for finding the stability of the closed-loop control systems. This is done by varying ω from −∞ to ∞, i.e. Nyquist plots are used to draw the complete frequency response of the open-loop transfer function.
Method of drawing Nyquist plot:

• Locate the poles and zeros of open-loop transfer function G(s)H(s) in ‘s’ plane.
• Draw the polar plot by varying ω from zero to infinity.
• Draw the mirror image of the above polar plot for values of ω ranging from −∞ to zero.
• The number of infinite radii half circles will be equal to the number of poles at the origin.
• The infinite radius half-circle will start at the point where the mirror image of the polar plot ends. And this infinite radius half-circle will end at the point where the polar plot starts.

The given frequency response is

In Anti-clockwise the phase order is 0, 90, 180, 270, 360 or 0.
In clockwise the phase angle order is 0, -90, -180, -270, -360 or 0.
Here, 90^∘  = -270^∘  and 270^∘ = -90^∘ 

At ω = ω_c (Cut-off frequency), ∠ G(jω) = -180^∘ 
−90 − tan⁻¹ω_c − tan⁻¹0.5ω_c = −180
tan⁻¹ωc + tan⁻¹0.5ω_c = 90

1 - 0.5ω_c² = 0
ω_c = 1.414 rad/sec
At ω = ω_c 
|G(jω)| = (1/6) 
The polar plot for given transfer function is

Polar plot:
The Polar plot is a plot, which can be drawn between the magnitude and the phase angle of the transfer function by varying frequency from 0 to ∞.
Given,

the magnitude of the transfer function will be:

The phase of the transfer function will be:
ϕ = tan^-1(ω) - tan^-1ω(ω/10)
At ω = 0
M₁ = 1
ϕ₁ = 0° 
At ω = ∞ 
M₂ = 10
ϕ₂ = 0° 

The gain margin of the system is 23.9 dB

∴ phase crossover frequency W_pc = 15.7 rad
∴ at W_pc = 15.7 rad we will get the phase of -180º

-180º = -K(900) -90º
∴ K = 90/900 
= 0.1

It is a lead compensator
(∴ Polar plot lies in 1^st quadrant)

1. Gain margin (GM): The gain margin of the system defines by how much the system gain can be increased so that the system moves on the edge of stability.
2. It is determined from the gain at the phase cross-over frequency.
3. Phase crossover frequency (ωpc): It is the frequency at which the phase angle of G(s) H(s) is -180°.
4. Phase margin (PM): The phase margin of the system defines by how much the phase of the system can increase to make the system unstable.
5. It is determined from the phase at the gain cross over frequency.
6. Gain crossover frequency (ωgc): It is the frequency at which the magnitude of G(s) H(s) is unity.
   
7. So it is important to note that these margins of stability are valid for open-loop stable systems only.
8. A large gain margin or a large phase margin indicates a very stable feedback system but usually a very sluggish response.
9. Hence a Gain margin close to unity (or 0 in dB) or a phase margin close to zero corresponds to a highly oscillatory system.

Hence option (3) is the correct answer.
Gain margin and phase margin are frequently used for frequency response specifications by designers. Usually a Gain margin of about 6 dB or a Phase margin of 30 - 35° results in a reasonably good degree of relative stability.
Important Points

• If both GM and PM are positive, the system is stable (ω_gc < ω_pc)
• If both GM and PM are negative, the system is unstable (ω_gc > ω_pc)
• If both GM and PM are zero, the system is just stable (ω_gc = ω_pc)

Polar plot:

• The polar plot of a transfer function G(jω) is the plot of the magnitude of G(jω) versus the phase angle of G(jω) as ω is varied from 0 to positive infinity.
• For all pole systems, type indicates the starting point of the polar plot and order indicates the ending point of the polar plot.

The sinusoidal transfer function G(jω) is a complex function and it is given by
G(jω) = Re [G(jω)] + j Im [G(jω)]
G(jω) = |G(jω)| ∠ G(jω)
= M ∠ϕ Polar form
From the above equation,
G(jω) may be represented as a phasor of magnitude M and phase angle ϕ
The starting points (ω = 0) of a polar plot for different types of minimum phase systems is given below:

 

• As seen from the above figure, when a zero is added the type decreases, and the end of the polar plot shifts by +90°. 
• When a pole is added, the type of the system increases, and hence the end of the polar plot shifts by -90°. 

Therefore, the Polar plot of the sinusoidal transfer function is a plot of magnitude and phase angle.

Polar plot:

• The polar plot of a transfer function G(jω) is the plot of the magnitude of G(jω) versus the phase angle of G(jω) as ω is varied from 0 to positive infinity.
• For all pole systems, type indicates the starting point of the polar plot and order indicates the ending point of the polar plot.

• As seen from the above figure, when a zero is added the type decreases, and the end of the polar plot shifts by +90°. 
• When a pole is added, the type of the system increases, and hence the end of the polar plot shifts by -90°. 

Calculation:
Let the transfer function be:

 

The total phase shift will be:
∠G(jω)H(jω) = -90° - tan^-1(ωT) - 180°   ----(1)
From equation (1) we can say that constant K has no contribution to the phase plot.
Hence K contributes 180° to the phase plot.
So option (c) is the correct answer.

Concept:

• The stability of the control system is based on the relation between gain margin and phase margin as 

• Gain margin GM is defined as the negative of the magnitude in dB, at phase cross over frequency,
• The phase margin of a system is defined as: PM = 180° + ϕ_gc

Gain margin (GM) and Phase margin (PM) from the polar plot:
Let us consider the polar plot as shown below,

Figure: A polar plot of a stable system
Gain margin (GM):
The frequency at which the polar plot crosses the negative real axis is called a phase cross-over frequency (ω_pc).
Let 'a' be the point of intersection and it is the magnitude at the phase cross-over frequency.
⇒ a = | G(jω_pc) H(jω_pc) |
And, we know that 
Gain margin (GM) = 1 / |G(jω_pc) H(jω_pc)| = 1 / a
Gain margin in dB = 20 log (1 / a)
Calculations:
​In the Given polar plot;


Phase margin (PM):
The frequency at which the polar plot crosses the unit circle (formed with the radius of the critical point) is called again cross-over frequency (ωgc).
From the polar plot, we can observe that
Phase margin (PM) = 180 - ∠G(jω_gc) H(jω_gc​)

From the given polar plot,

At ω = 0, magnitude = 1, angle = 0°

Therefore, there are no poles or zeros at the origin.

At ω = ∞, magnitude = 0, angle = -270°

Therefore, the number of poles = 3

From the above two conditions, the transfer function will be