Match the list
List-I
Material used
A. Maganin
B. Aluminium
C. Phosphor Bronze
D. Eureka
List-II
Purpose
1. Multiplier
2. Coils
3. Discs
4. Control spring
5. Shunt
Match the lists
List-I
(Types of Measurement)
A. Resistance of the order of m?
B. Capacitance between Machine
Winding and Earth.
C. Inductance of Armature winding of d.c. Machine
D. To detect quality of the output
waveform of Inverter.
List-II
(Measuring Instrument)
1. Wein’s Bridge
2. Kelvin’s Double Bridge
3. Schering’s Bridge
4. Carey foster’s Bridge
5. Ander Son’s Bridge
1 Crore+ students have signed up on EduRev. Have you? Download the App |
The Eddy current damping is not used in electrodynamometer type instrument as
Manganin is preferred to constantan as a shunt wire in Ammeter in d.c. application, it is to
The limiting values of voltage, current and power factor of 1-induction motor is given as 200V 5%, 10A 2% and 0.8 10%. The limiting error of reactive power input is
The current through the current coil of wattmeter is 2 + 3 cos 2(t - 300) + 5cos(4t - 600) and voltage across
its pressure coil is 1 + 4 sin(2t - 300) + 3 sin (6t - 100). The reading of wattmeter will be
The inductance of a certain moving iron ammeter is given as L = 5 + 2θ - θ2μH where deflection θ is in
radians from zero position. If spring constant is 20 μNm/rad. The deflection for a current of 1A is
Two 50V full scale PMMC type D.C. Voltmeters having sensitivities of 5K/V and 10K/V are
connected in series. The sensitivity of the series combination is
A 10A D.C. Ammeter has a resistance of 0.1 is to be extended to 50A, the required shunt wire is
From the above circuit, the voltages are applied to X and Y plates, the value of coefficient of coupling to
observe a circle on CRO screen, (X and Y plates have equal V/div.)
A wattmeter reads P when its current coil is connected in the phase A and its PC is between phase
B & C of symmetrical 3- ABC system supplying a balanced Yconnected 0.6 pf capacitive load,
what will be the reading of wattmeter if CC is reversed as well as phase sequence is reversed by
interchanging phases B & C
A potentiometric transducer supplied by 10V d.c. and having total resistance 10K is used to
measure the linear displacement. At 60% of total travel to obtain the accuracy better than 98% for
measurement, the voltmeter should have a resistance atleast (approximately)
In the measurment of power of balanced load by two wattmeter method in a 3- circuit. The readings of the wattmeters are 4kW and 2 kW respectively, the later is taken after reversing the connections of current coil. The power factor and reactive power of the load is
A strain Gauge with Gauge factor 4 is bonded to a steel beam is subjected to a stress of 5 x 105 kN/
m2. The modulus of elasticity of steel of 20 GN/m2, the change in the resistance of guage is
An electrodynamometer type wattmeter is provided with a capacitor across the resistance in its Potential coil. It is required mainly when
A 10KV, 50Hz supply is fed to Bridge rectifier type (using ideal diodes) EVM through a capacitor.
The 1A PMMC, of negligible resistance, is provided in series with 6K resistance. The value of
capacitor to obtain 90% of full obtain deflection in PMMC is
In a 100V PMMC type voltmeter, where 40V is measured, the pointer goes upto the 40.6 before finally
settling at 40V. If due to the increment in temperature, stiffness of spring gets reduced by 20%. The
maximum swing of pointer when measured 80% of FSD, is
A resistance is measured by the voltmeter-ammeter method employing d.c. excitation and a voltmeter of very high resistance connected directly across the unknown resistance. If the voltmeter and ammeter readings are subject to maximum possible errors of 2.4% and 1% respectively,
than the magnitude of the maximum possible percentage error in the value of resistance deduced
from the measurement is nearly
In the Wheatstone Bridge shown in figure.
Current I in the shown figure is,
The current coil and potential coil of a dynamometer type wattmeter were accidently interchanged while
connecting, After energizing the circuit, it was observed that the wattmeter did not show the reading.
This could be due to the
In the circuit shown in the given figure, the wattmeter Reading will be
In an energy meter, the current and flux adjustment of series magnet are in phase while there is an angular
departure of 50 from quadrature between voltage and shunt magnetic flux. The speed of disc at
full load and unity power factor is 50 rpm. The error of the disc at 60% of full load and 0.8 power
factor lag is_____
25 docs|263 tests
|
25 docs|263 tests
|