Civil Engineering (CE)  >  Civil Engineering SSC JE (Technical)  >  Technical Mock Test CE (SSC JE)- 6 Download as PDF

Technical Mock Test CE (SSC JE)- 6


Test Description

100 Questions MCQ Test Civil Engineering SSC JE (Technical) | Technical Mock Test CE (SSC JE)- 6

Technical Mock Test CE (SSC JE)- 6 for Civil Engineering (CE) 2023 is part of Civil Engineering SSC JE (Technical) preparation. The Technical Mock Test CE (SSC JE)- 6 questions and answers have been prepared according to the Civil Engineering (CE) exam syllabus.The Technical Mock Test CE (SSC JE)- 6 MCQs are made for Civil Engineering (CE) 2023 Exam. Find important definitions, questions, notes, meanings, examples, exercises, MCQs and online tests for Technical Mock Test CE (SSC JE)- 6 below.
Solutions of Technical Mock Test CE (SSC JE)- 6 questions in English are available as part of our Civil Engineering SSC JE (Technical) for Civil Engineering (CE) & Technical Mock Test CE (SSC JE)- 6 solutions in Hindi for Civil Engineering SSC JE (Technical) course. Download more important topics, notes, lectures and mock test series for Civil Engineering (CE) Exam by signing up for free. Attempt Technical Mock Test CE (SSC JE)- 6 | 100 questions in 100 minutes | Mock test for Civil Engineering (CE) preparation | Free important questions MCQ to study Civil Engineering SSC JE (Technical) for Civil Engineering (CE) Exam | Download free PDF with solutions
1 Crore+ students have signed up on EduRev. Have you?
Technical Mock Test CE (SSC JE)- 6 - Question 1

Pick up the correct statement from the following:Method of sawing timber

Technical Mock Test CE (SSC JE)- 6 - Question 2

Based on its dry weight, a freshly felled tree maycontain water upto

Technical Mock Test CE (SSC JE)- 6 - Question 3

A well seasoned timber may contain moisture up to

Technical Mock Test CE (SSC JE)- 6 - Question 4

The pigment used in paints for corrosive resistance, is

Technical Mock Test CE (SSC JE)- 6 - Question 5

The steel used for rails under heavy traffic and on sharp curves, is

Technical Mock Test CE (SSC JE)- 6 - Question 6

Dorry's testing machine is used for

Technical Mock Test CE (SSC JE)- 6 - Question 7

For a good building stone, its specific gravity should the greater than

Technical Mock Test CE (SSC JE)- 6 - Question 8

Match List-I with List-II and select a suitable answer by using the codes given below the lists:

Technical Mock Test CE (SSC JE)- 6 - Question 9

The 9cm ×9 cm side of a brick as seen in thewall face, is generally known as

Technical Mock Test CE (SSC JE)- 6 - Question 10

The portion of a brick cut across the width, is called

Technical Mock Test CE (SSC JE)- 6 - Question 11

Cavity wall is generally provided for

Technical Mock Test CE (SSC JE)- 6 - Question 12

The type of bond in which every course contains both headers and stretchers, is called

Technical Mock Test CE (SSC JE)- 6 - Question 13

The type of bond in a brick masonry containing alternate courses of stretchers and headers, is called

Technical Mock Test CE (SSC JE)- 6 - Question 14

 The following operations refer to the preparation of clay:

1. Weathering

2. Tempering

3. Cleaning

4. Blending

Their correct sequence is :

Technical Mock Test CE (SSC JE)- 6 - Question 15

Greater accuracy in linear measurements, is obtained by

Technical Mock Test CE (SSC JE)- 6 - Question 16

Cross hair in surveying telescopes, are fitted

Technical Mock Test CE (SSC JE)- 6 - Question 17

In setting up a plane table at any station

Technical Mock Test CE (SSC JE)- 6 - Question 18

Plotting of inaccessible points on a plane table,is done by

Technical Mock Test CE (SSC JE)- 6 - Question 19

One of the Lehmann's rules of plane tabling, is

Technical Mock Test CE (SSC JE)- 6 - Question 20

Imaginary line passing through points having equal magnetic declination is termed as

Technical Mock Test CE (SSC JE)- 6 - Question 21

Match list I with List II and select the correct answer by using the codes given below the lists:

Technical Mock Test CE (SSC JE)- 6 - Question 22

According to Unwin's formula, the diameter d of a rivet of plate of thickness t is :

Technical Mock Test CE (SSC JE)- 6 - Question 23

The weakest section of a diamond riveting, is the section which passes through

Technical Mock Test CE (SSC JE)- 6 - Question 24

Maximum deflection of a centilever due to pure bending moment M at its free end, is

Technical Mock Test CE (SSC JE)- 6 - Question 25

Match List-I with List-II and select a correct answer by using the codes given below to lists:

 

Technical Mock Test CE (SSC JE)- 6 - Question 26

The shape of the bending moment diagram over the length of a beam, having no external load. is always

Technical Mock Test CE (SSC JE)- 6 - Question 27

The effect of arching a beam, is

Technical Mock Test CE (SSC JE)- 6 - Question 28

A three-hinged arch is said to be:

Technical Mock Test CE (SSC JE)- 6 - Question 29

The shear stress at any section of a shaft ismaximum

Technical Mock Test CE (SSC JE)- 6 - Question 30

In a loaded beam, the point of contraflexture occurs at a section where

Technical Mock Test CE (SSC JE)- 6 - Question 31

The bending moment at C of a portal frame shown in figure is

Technical Mock Test CE (SSC JE)- 6 - Question 32

Match List-I with List-II and select a correct answer by using the codes given below to lists:

Technical Mock Test CE (SSC JE)- 6 - Question 33

For the two dimensional flow, the stream functionis given by ψ =2xy. The velocity at a point (3,4) is

Technical Mock Test CE (SSC JE)- 6 - Question 34

Euler's equation for motion of liquids, is given by

Technical Mock Test CE (SSC JE)- 6 - Question 35

For solving network problem of pipes, necessary condition is

Technical Mock Test CE (SSC JE)- 6 - Question 36

If k is the radius of gyration, h the metacentric height, g the acceleration due to gravity, the time
of oscillation of a floating body, is

Technical Mock Test CE (SSC JE)- 6 - Question 37

The time required to close a valve gradually is

Technical Mock Test CE (SSC JE)- 6 - Question 38

Match List-I with List-II and select a correct answer by using the codes given below to lists:

Technical Mock Test CE (SSC JE)- 6 - Question 39

The best side slope for most economical trapezoidal section, is

Technical Mock Test CE (SSC JE)- 6 - Question 40

If   pressure gradient, r = radius at any point, R is radius of the pipe, and Umax is central line velocity , m is average velocity, μ. is coefficient of viscosity and D is diameter of the pipe, then match List-I with List-II and choose the correct

Technical Mock Test CE (SSC JE)- 6 - Question 41

Match List-I with List-II and select a correct answer by using the codes given below to lists:

Technical Mock Test CE (SSC JE)- 6 - Question 42

The pipe mains carrying water from the source to the reservoir are designed for the

Technical Mock Test CE (SSC JE)- 6 - Question 43

The per capita water demand include

Technical Mock Test CE (SSC JE)- 6 - Question 44

The “distribution mains” are designed for

Technical Mock Test CE (SSC JE)- 6 - Question 45

Match the columns most appropriately :
Water pipe material                 Average age of pipe
a. Cast iron                                1. 75 years
b. Steel                                       2. 100 years
c. R.C.C.                                    3. 40 years

Technical Mock Test CE (SSC JE)- 6 - Question 46

Consider the following statements :
The basic difference between water pipes and sewer pipes is
1. in the material used for the pipes
2. in the pressure of the liquid flow
3. in the suspended solids they carry
Which of these statements is/are correct ?

Technical Mock Test CE (SSC JE)- 6 - Question 47

A commonly used handpump is the

Technical Mock Test CE (SSC JE)- 6 - Question 48

The threshold odour number (TON) for a water sample of 40 ml, dilute to standard 200 mlmixture, in which odour is just barely detectable to the sense of smell, is

Detailed Solution for Technical Mock Test CE (SSC JE)- 6 - Question 48

Threshold odour number represent the dilution ratio at which the odour is hardly detectable.
T.O.N. = 200/40 = 5

Technical Mock Test CE (SSC JE)- 6 - Question 49

Water is considered ‘hard’, if its hardness is of the order of

Technical Mock Test CE (SSC JE)- 6 - Question 50

Match List-I (Water-born disease) with List- II (Pollution causing) and select the correct
answer using the codes given below the lists :

Technical Mock Test CE (SSC JE)- 6 - Question 51

The temporary hardness of water is caused by

Technical Mock Test CE (SSC JE)- 6 - Question 52

Total Kjeldahi nitrogen is a measure of

Technical Mock Test CE (SSC JE)- 6 - Question 53

Match List-I (Distribution system) with List-II (Characteristics) and select the correct answer
using the codes given below the lists :

List-I
a. Tree system
b. Grid-iron or reticulation system
c. Circular system
d. Radial system
 

List-II
1. Main lines are laid along the periphery covering the entire area
2. Calculations are simple and accurate flow determination is also possible at any line
3. Large number of cut-off valve and longer pipe lengths are required
4. Flow from centre to periphery

 

Technical Mock Test CE (SSC JE)- 6 - Question 54

The low velocity in sewer pipe may cause

Technical Mock Test CE (SSC JE)- 6 - Question 55

The pH of fresh sewage is usually

Technical Mock Test CE (SSC JE)- 6 - Question 56

Match List-I (Type of waste) with List-II (Description) and select the correct answer using
the codes given below the lists :

List-I
a. Refuse
b. Sullage
c. Sewage
d. Rubbish
List-II
1. Wastes of combustible nature
2. Waste water with higher decomposable fraction
3. All kinds of wastes
4. Waste water with low biodegradable fraction

Technical Mock Test CE (SSC JE)- 6 - Question 57

Which of the following is a weakness of bar chart?

Technical Mock Test CE (SSC JE)- 6 - Question 58

The process of incorporating changes and rescheduling or replanning is called

Technical Mock Test CE (SSC JE)- 6 - Question 59

The basic action involved in sheep foot rolling is

Technical Mock Test CE (SSC JE)- 6 - Question 60

Batching refers to

Technical Mock Test CE (SSC JE)- 6 - Question 61

A reinforced concrete slab is 75 mm thick. The maximum size of reinforced bar that can be usedis of

Technical Mock Test CE (SSC JE)- 6 - Question 62

In case of simply supported beam, the clear distance between lateral restrains shall not exceed

Technical Mock Test CE (SSC JE)- 6 - Question 63

In case of 2-way slab, the limiting deflection of the slab is

Technical Mock Test CE (SSC JE)- 6 - Question 64

A reinforced concrete member is subjected tocombined action of combined action ofcompressive axial force and bending moment. If ∈cis the best least compressive strain in themember, fy, the yield stress of steel and, Es, themodulus of elasticity of steel, the maximum permissible compressive strain in concrete member will be

Technical Mock Test CE (SSC JE)- 6 - Question 65

Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively are

Technical Mock Test CE (SSC JE)- 6 - Question 66

If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, thebeam is called:

Technical Mock Test CE (SSC JE)- 6 - Question 67

The minimum reinforced using mild steel in slab should not be less than.

Technical Mock Test CE (SSC JE)- 6 - Question 68

The average permissible stress in bond for plainbars in tension is

Technical Mock Test CE (SSC JE)- 6 - Question 69

Critical section for shear is case of flat slabs is ata distance of

Technical Mock Test CE (SSC JE)- 6 - Question 70

The diagonal tension whcih results in ultimate failure due to development of diagonal tension cracks, depends on

Technical Mock Test CE (SSC JE)- 6 - Question 71

Which one of the following is the correct expression to estimate the development length
of deformed reinforcing bar as per IS code in limit state design?

Detailed Solution for Technical Mock Test CE (SSC JE)- 6 - Question 71

Technical Mock Test CE (SSC JE)- 6 - Question 72

What is the anchorage value of a standard hook of reinforcement bar of diameter D?

Technical Mock Test CE (SSC JE)- 6 - Question 73

The bond strength between steel and concrete is due to

Technical Mock Test CE (SSC JE)- 6 - Question 74

Which one of the following is the mode of failure in a fillet weld material ?

Technical Mock Test CE (SSC JE)- 6 - Question 75

If 20 mm rivets are used in lacing bars, then the minimum width of lacing bar should be

Technical Mock Test CE (SSC JE)- 6 - Question 76

In a gusseted base, when the end of the column is machined for completer bearing on the baseplate, the axial load i sassumed to be transferred to the base plate

Technical Mock Test CE (SSC JE)- 6 - Question 77

Gusset plate is provided in column base connection to

Technical Mock Test CE (SSC JE)- 6 - Question 78

The web crippling due to excessive bearing stress can be avoided by

Technical Mock Test CE (SSC JE)- 6 - Question 79

Intermediate vertical stiffeners are provided in plate girders to

Technical Mock Test CE (SSC JE)- 6 - Question 80

The maximum permissible deflection for gantry girder of span 6m on which an EOT crane o of capacity 200 kN is operating is

Technical Mock Test CE (SSC JE)- 6 - Question 81

Normally, the angle of roof truss with asbestos sheets should not be less than

Technical Mock Test CE (SSC JE)- 6 - Question 82

Arrange the following cross-section in the increasing order of their respective shape factors

Technical Mock Test CE (SSC JE)- 6 - Question 83

The traffic manoeuvre shown in fig. represents

Technical Mock Test CE (SSC JE)- 6 - Question 84

Equivalent factor of passenger car unit (PCU) for a passenger car as per IRC is

Technical Mock Test CE (SSC JE)- 6 - Question 85

The background colour of the informatory sign baord is

Technical Mock Test CE (SSC JE)- 6 - Question 86

Which of the following is indicated by a warning sign ?

Technical Mock Test CE (SSC JE)- 6 - Question 87

The critical combination of stresses for corner region in cement concrete roads is

Technical Mock Test CE (SSC JE)- 6 - Question 88

The function of an expansion joint in rigid pavements is to

Technical Mock Test CE (SSC JE)- 6 - Question 89

At liquid limit, all soils possess

Technical Mock Test CE (SSC JE)- 6 - Question 90

When a soil sample is subjected to a uniformly distributed fluid pressure only, in a triaxial
compression test, the Mohr's representation of the state of stress on sample is

Technical Mock Test CE (SSC JE)- 6 - Question 91

Sensitivity of a soil can be defined as

Technical Mock Test CE (SSC JE)- 6 - Question 92

When the degree of consolidation is 50% the time factor is about

Technical Mock Test CE (SSC JE)- 6 - Question 93

A rectangular footing LxB is to be placed at a depth D below ground level such that D/B < 2.5. The factor NC to be used in deciding on the allowable bearing capacity for the footing as given by Skempton is calculated using the equation (where R NC = NC for rectangular footing, S NC = NC at surface)

Technical Mock Test CE (SSC JE)- 6 - Question 94

Permissible settlement is relatively higher for

Detailed Solution for Technical Mock Test CE (SSC JE)- 6 - Question 94

IS code specification for permissible settlement:

(1) Total Permissible settlement:
For isolated footing on clay = 65 mm
For isolated footing on sand = 40 mm
For raft foundation on clay = 65-100 mm
For raft foundation on sand = 40-65 mm

(2) Permissible Differential settlement:
For isolated fotting on clay = 40 mm
For isolated footing on sand = 25 mm
From above data, it is observed that, total permissible settlement is higher for raft foundation on clay.

Technical Mock Test CE (SSC JE)- 6 - Question 95

A raingauge should preferably be fixed

Technical Mock Test CE (SSC JE)- 6 - Question 96

A flownet is drawn to obtain

Technical Mock Test CE (SSC JE)- 6 - Question 97

A dry sand specimen is put through a triaxial test.The cell pressure is 50 kPa and the deviator stressat failure is 100 kPa. The angle of internal frictionfor the sand specimen is

Technical Mock Test CE (SSC JE)- 6 - Question 98

Ringelmenn's scale is used to

Technical Mock Test CE (SSC JE)- 6 - Question 99

Optimum depth of kor watering for rice is

Technical Mock Test CE (SSC JE)- 6 - Question 100

Figures given below indicate the weights of different pycnometers.

Use Code STAYHOME200 and get INR 200 additional OFF
Use Coupon Code
Information about Technical Mock Test CE (SSC JE)- 6 Page
In this test you can find the Exam questions for Technical Mock Test CE (SSC JE)- 6 solved & explained in the simplest way possible. Besides giving Questions and answers for Technical Mock Test CE (SSC JE)- 6, EduRev gives you an ample number of Online tests for practice