Description

This mock test of Test: Strength Of Material- 2 for Mechanical Engineering helps you for every Mechanical Engineering entrance exam.
This contains 25 Multiple Choice Questions for Mechanical Engineering Test: Strength Of Material- 2 (mcq) to study with solutions a complete question bank.
The solved questions answers in this Test: Strength Of Material- 2 quiz give you a good mix of easy questions and tough questions. Mechanical Engineering
students definitely take this Test: Strength Of Material- 2 exercise for a better result in the exam. You can find other Test: Strength Of Material- 2 extra questions,
long questions & short questions for Mechanical Engineering on EduRev as well by searching above.

QUESTION: 1

If a column is changed from both ends fixed toboth ends hinged its load carrying capacity .

Solution:

QUESTION: 2

Shown below are two cross sections of two shafts 1 and 2. The ratio of maximum torque carring capacity . If they are made of same material is

d/D = 1/2

Solution:

QUESTION: 3

The maximum deflection of a simply supported beam due to its self weight (W) is.

Solution:

QUESTION: 4

It flexural strength decreases the maximum slopeof any beam

Solution:

QUESTION: 5

If temperature of a freely hanging bar is increasedit will develope : -

Solution:

QUESTION: 6

Find the increase in temperature (DT) so that the gap gets filled

Solution:

QUESTION: 7

The ratio of hoop stress for a thin cylinder andthin spherical pressure vessel is

Solution:

QUESTION: 8

A spherical pressure vessel is to be designed tohold 40 MPa pressure and Diameter should be200 mm. If max stress can be 200 MPa find thethickness required.

Solution:

QUESTION: 9

Shown below is a B.M.D.

The SFD will be

Solution:

QUESTION: 10

Shown is a B.M.D

The shear force is zero at

Solution:

QUESTION: 11

Shown is a B.M.D

In the above diagram point of contraflexure is

Solution:

QUESTION: 12

In the above shown BMD, the beam is mostprobably

Solution:

QUESTION: 13

Strain Energy for the shown beam is

Solution:

QUESTION: 14

The B.M.D. for a cantilever beam due to its selfweight is

Solution:

QUESTION: 15

For a structural member the principle stressesare equal but opposite in nature . The center ofmohr's circle will

Solution:

QUESTION: 16

The maximum shear stress in a mohr's circle isequal to

Solution:

QUESTION: 17

A spring of length 'L' is cut into 5 equal parts if initial spring stiffness was R the final stiffness after

parallel combination of all 5 parts will be

Solution:

QUESTION: 18

It E is the young's Modulus, the minimum value of bulk modulus is

Solution:

QUESTION: 19

It the dimentions of a prismatic bar hanging fromroof are doubled, the elongation due to its selfweight will become

Solution:

QUESTION: 20

A long shaft of diameter d is subjected to twisting moment of T. The maximum normal stress acting

at the cross- section is equal to :-

Solution:

QUESTION: 21

For shafts in parallel which of the following willbe same for all shafts.

Solution:

QUESTION: 22

How many minimum values among E, G, K, Mwould you require for a isotropic andhomogenous material to determine all state ofstress.

Solution:

QUESTION: 23

The maximum shear stress in a shaft of Diameter100 mm is 100MPa. The shear stress at adistance of 30 mm from center is .

Solution:

QUESTION: 24

The depth of a beam of uniform strength vary : -

Solution:

QUESTION: 25

Which of the following is must for a strut.

Solution:

### Material Strength, Ductility, and Toughness

Video | 07:19 min

### Triaxial Test: Shear Strength

Video | 12:55 min

### STRESSES - STRENGTH OF MATERIAL BY IIT MADRAS

Doc | 23 Pages

### TORSION-strength of material by IIT MADRAS

Doc | 12 Pages

- Test: Strength Of Material- 2
Test | 25 questions | 50 min

- Test: Strength Of Material (Level- 2)- 2
Test | 25 questions | 50 min

- Strength Of Material 2
Test | 20 questions | 12 min

- Strength Of Material 2 MCQ
Test | 20 questions | 12 min

- Strength Of Material 1
Test | 20 questions | 12 min