Description

This mock test of Measurement for GATE helps you for every GATE entrance exam.
This contains 25 Multiple Choice Questions for GATE Measurement (mcq) to study with solutions a complete question bank.
The solved questions answers in this Measurement quiz give you a good mix of easy questions and tough questions. GATE
students definitely take this Measurement exercise for a better result in the exam. You can find other Measurement extra questions,
long questions & short questions for GATE on EduRev as well by searching above.

QUESTION: 1

Match the list

**List-I**

Material used

A. Maganin

B. Aluminium

C. Phosphor Bronze

D. Eureka

**List-II**

Purpose

1. Multiplier

2. Coils

3. Discs

4. Control spring

5. Shunt

Solution:

QUESTION: 2

**Match the lists
List-I**

A. Resistance of the order of m?

B. Capacitance between Machine

Winding and Earth.

C. Inductance of Armature winding of d.c. Machine

D. To detect quality of the output

waveform of Inverter.

(Measuring Instrument)

1. Wein’s Bridge

2. Kelvin’s Double Bridge

3. Schering’s Bridge

4. Carey foster’s Bridge

5. Ander Son’s Bridge

Solution:

QUESTION: 3

The Eddy current damping is not used in electrodynamometer type instrument as

Solution:

QUESTION: 4

Manganin is preferred to constantan as a shunt wire in Ammeter in d.c. application, it is to

Solution:

QUESTION: 5

The limiting values of voltage, current and power factor of 1-induction motor is given as 200V 5%, 10A 2% and 0.8 10%. The limiting error of reactive power input is

Solution:

QUESTION: 6

The current through the current coil of wattmeter is 2 + 3 cos 2(t - 300) + 5cos(4t - 600) and voltage across

its pressure coil is 1 + 4 sin(2t - 300) + 3 sin (6t - 100). The reading of wattmeter will be

Solution:

QUESTION: 7

The inductance of a certain moving iron ammeter is given as L = 5 + 2θ - θ^{2}μH where deflection θ is in

radians from zero position. If spring constant is 20 μNm/rad. The deflection for a current of 1A is

Solution:

QUESTION: 8

Two 50V full scale PMMC type D.C. Voltmeters having sensitivities of 5K/V and 10K/V are

connected in series. The sensitivity of the series combination is

Solution:

First meter shows half of FSD i.e.

25V and second meter shows FDS

i.e. SoV.

So voltage that can be measured

using combination = 75V.

QUESTION: 9

A 10A D.C. Ammeter has a resistance of 0.1 is to be extended to 50A, the required shunt wire is

Solution:

QUESTION: 10

From the above circuit, the voltages are applied to X and Y plates, the value of coefficient of coupling to

observe a circle on CRO screen, (X and Y plates have equal V/div.)

Solution:

QUESTION: 11

A wattmeter reads P when its current coil is connected in the phase A and its PC is between phase

B & C of symmetrical 3- ABC system supplying a balanced Yconnected 0.6 pf capacitive load,

what will be the reading of wattmeter if CC is reversed as well as phase sequence is reversed by

interchanging phases B & C

Solution:

QUESTION: 12

In the wheatstone Bridge the V_{0} is (approximately)

Solution:

QUESTION: 13

A potentiometric transducer supplied by 10V d.c. and having total resistance 10K is used to

measure the linear displacement. At 60% of total travel to obtain the accuracy better than 98% for

measurement, the voltmeter should have a resistance atleast (approximately)

Solution:

QUESTION: 14

In the measurment of power of balanced load by two wattmeter method in a 3- circuit. The readings of the wattmeters are 4kW and 2 kW respectively, the later is taken after reversing the connections of current coil. The power factor and reactive power of the load is

Solution:

QUESTION: 15

A strain Gauge with Gauge factor 4 is bonded to a steel beam is subjected to a stress of 5 x 10^{5} kN/

m^{2}. The modulus of elasticity of steel of 20 GN/m^{2}, the change in the resistance of guage is

Solution:

QUESTION: 16

An electrodynamometer type wattmeter is provided with a capacitor across the resistance in its Potential coil. It is required mainly when

Solution:

In Low power factor ED type

wattmeter Potential coil inductance

is compensated by capacitor across

the resistance of PC.

QUESTION: 17

In the circuit shown the reading of wattmeter is

Solution:

QUESTION: 18

A 10KV, 50Hz supply is fed to Bridge rectifier type (using ideal diodes) EVM through a capacitor.

The 1A PMMC, of negligible resistance, is provided in series with 6K resistance. The value of

capacitor to obtain 90% of full obtain deflection in PMMC is

Solution:

QUESTION: 19

In a 100V PMMC type voltmeter, where 40V is measured, the pointer goes upto the 40.6 before finally

settling at 40V. If due to the increment in temperature, stiffness of spring gets reduced by 20%. The

maximum swing of pointer when measured 80% of FSD, is

Solution:

of 80V = 81.47V

QUESTION: 20

A resistance is measured by the voltmeter-ammeter method employing d.c. excitation and a voltmeter of very high resistance connected directly across the unknown resistance. If the voltmeter and ammeter readings are subject to maximum possible errors of 2.4% and 1% respectively,

than the magnitude of the maximum possible percentage error in the value of resistance deduced

from the measurement is nearly

Solution:

QUESTION: 21

In the Wheatstone Bridge shown in figure.

Current I in the shown figure is,

Solution:

Given WSB

QUESTION: 22

Solution:

Therefore

For R_{x} max; R_{4} & C_{1} is maximum

& for L_{x} max; C_{1} max & R_{4} is

maximum

.

QUESTION: 23

The current coil and potential coil of a dynamometer type wattmeter were accidently interchanged while

connecting, After energizing the circuit, it was observed that the wattmeter did not show the reading.

This could be due to the

Solution:

As the resistance of current coil is

low if it is connected across high

voltage , the maximum current is

flowing through it and a large

voltage drop takes place due to

which it gets damaged.

QUESTION: 24

In the circuit shown in the given figure, the wattmeter Reading will be

Solution:

*Answer can only contain numeric values

QUESTION: 25

In an energy meter, the current and flux adjustment of series magnet are in phase while there is an angular

departure of 50 from quadrature between voltage and shunt magnetic flux. The speed of disc at

full load and unity power factor is 50 rpm. The error of the disc at 60% of full load and 0.8 power

factor lag is_____

Solution:

### Temperature Measurement - Measurement Systems

Doc | 14 Pages

### Time Measurement : Measurement of Distances

Video | 06:41 min

### Pressure measurement

Doc | 16 Pages

### Flow Measurement

Doc | 1 Page

- Measurement
Test | 25 questions | 75 min

- Olympiad Test: Measurement - 1
Test | 10 questions | 20 min

- Fluid Pressure And Measurement
Test | 10 questions | 30 min

- Streamflow Measurement - 2
Test | 10 questions | 30 min

- Pressure & Its Measurement - 1
Test | 10 questions | 30 min