JEE Exam > JEE Notes > DC Pandey Solutions for JEE Physics > DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics PDF Download
| Download, print and study this document offline |
Please wait while the PDF view is loading
Page 1
Exercises
For JEE Main
Subjective Questions
First Law of Thermodynamics
Q 1. In a certain chemical process, a lab technician supplies 254 J of heat to a system. At the same time,
73 J of work are done on the system by its surroundings. What is the increase in the internal
energy of the system?
Q 2. One mole of an ideal monoatomic gas is initially at 300 K. Find the final temperature if 200 J of
heat are added as follows :
(a) at constant volume, (b) at constant pressure.
Q 3. Show how internal energy U varies with T in isochoric, isobaric and adiabatic process?
Q 4. A closed vessel 10 L in volume contains a diatomic gas under a pressure of 10
5
N/ m
2
. What
amount of heat should be imparted to the gas to increase the pressure in the vessel five times ?
Q 5. A diatomic ideal gas is heated at constant volume until its pressure becomes three times. It is again
heated at constant pressure until its volume is doubled. Find the molar heat capacity for the whole
process.
Q 6. Two moles of a certain gas at a temperature T0 = 300 K were cooled isochorically so that the
pressure of the gas got reduced 2 times. Then as a result of isobaric process, the gas is allowed to
expand till its temperature got back to the initial value. Find the total amount of heat absorbed by
gas in this process.
Q 7. Five moles of an ideal monoatomic gas with an initial temperature of 127° C expand and in the
process absorb 1200 J of heat and do 2100 J of work . What is the final temperature of the gas ?
Q 8. An ideal gas expands while the pressure is kept constant. During this process, does heat flow into
the gas or out of the gas? Justify your answer.
Q 9. Find the change in the internal energy of 2 kg of water as it is heated from 0° C to 4° C. The
specific heat capacity of water is 4200J/kg –K and its densities at 0° C and 4°C are 999.9 kg/m
3
and 1000 kg/m
3
respectively. Atmospheric pressure = 10
5
Pa.
Q 10. Calculate the increase in the internal energy of 10 g of water when it is heated from 0° C to 100° C
and converted into steam at 100 kPa. The density of steam = 0.6 kg/m
3
. Specific heat capacity of
water = 4200 J/kg-° Cand the latent heat of vaporization of water = 2.5 × 10
6
J/kg.
Q 11. One gram of water (1 cm
3
) becomes 1671cm of steam when boiled at a constant pressure of 1 atm
(1.013 × 10
5
Pa). The heat of vaporization at this pressure is Lv = 2.256 × 10
6
J/kg. Compute (a)
the work done by the water when it vaporizes and (b) its increase in internal energy.
Q 12. A gas in a cylinder is held at a constant pressure of 2.30 × 10
5
Pa and is cooled and compressed
from 1.70 m
3
to 1.20 m
3
. The internal energy of the gas decreases by 1.40 × 10
5
J. (a) Find the
work done by the gas. (b) Find the absolute value | Q | of the heat flow into or out of the gas and
state the direction of the heat flow. (c) Does it matter whether or not the gas is ideal ? Why or why
not?
Cyclic Process and Efficiency of Cycle
Q 13. An ideal gas is taken through a cyclic thermodynamic process through four steps. The amounts of
heat involved in these steps are Q1 =5960J, Q2 =-5585J,Q3 = -2980J and Q4 = 3645 J respectively.
Page 2
Exercises
For JEE Main
Subjective Questions
First Law of Thermodynamics
Q 1. In a certain chemical process, a lab technician supplies 254 J of heat to a system. At the same time,
73 J of work are done on the system by its surroundings. What is the increase in the internal
energy of the system?
Q 2. One mole of an ideal monoatomic gas is initially at 300 K. Find the final temperature if 200 J of
heat are added as follows :
(a) at constant volume, (b) at constant pressure.
Q 3. Show how internal energy U varies with T in isochoric, isobaric and adiabatic process?
Q 4. A closed vessel 10 L in volume contains a diatomic gas under a pressure of 10
5
N/ m
2
. What
amount of heat should be imparted to the gas to increase the pressure in the vessel five times ?
Q 5. A diatomic ideal gas is heated at constant volume until its pressure becomes three times. It is again
heated at constant pressure until its volume is doubled. Find the molar heat capacity for the whole
process.
Q 6. Two moles of a certain gas at a temperature T0 = 300 K were cooled isochorically so that the
pressure of the gas got reduced 2 times. Then as a result of isobaric process, the gas is allowed to
expand till its temperature got back to the initial value. Find the total amount of heat absorbed by
gas in this process.
Q 7. Five moles of an ideal monoatomic gas with an initial temperature of 127° C expand and in the
process absorb 1200 J of heat and do 2100 J of work . What is the final temperature of the gas ?
Q 8. An ideal gas expands while the pressure is kept constant. During this process, does heat flow into
the gas or out of the gas? Justify your answer.
Q 9. Find the change in the internal energy of 2 kg of water as it is heated from 0° C to 4° C. The
specific heat capacity of water is 4200J/kg –K and its densities at 0° C and 4°C are 999.9 kg/m
3
and 1000 kg/m
3
respectively. Atmospheric pressure = 10
5
Pa.
Q 10. Calculate the increase in the internal energy of 10 g of water when it is heated from 0° C to 100° C
and converted into steam at 100 kPa. The density of steam = 0.6 kg/m
3
. Specific heat capacity of
water = 4200 J/kg-° Cand the latent heat of vaporization of water = 2.5 × 10
6
J/kg.
Q 11. One gram of water (1 cm
3
) becomes 1671cm of steam when boiled at a constant pressure of 1 atm
(1.013 × 10
5
Pa). The heat of vaporization at this pressure is Lv = 2.256 × 10
6
J/kg. Compute (a)
the work done by the water when it vaporizes and (b) its increase in internal energy.
Q 12. A gas in a cylinder is held at a constant pressure of 2.30 × 10
5
Pa and is cooled and compressed
from 1.70 m
3
to 1.20 m
3
. The internal energy of the gas decreases by 1.40 × 10
5
J. (a) Find the
work done by the gas. (b) Find the absolute value | Q | of the heat flow into or out of the gas and
state the direction of the heat flow. (c) Does it matter whether or not the gas is ideal ? Why or why
not?
Cyclic Process and Efficiency of Cycle
Q 13. An ideal gas is taken through a cyclic thermodynamic process through four steps. The amounts of
heat involved in these steps are Q1 =5960J, Q2 =-5585J,Q3 = -2980J and Q4 = 3645 J respectively.
The corresponding quantities of work involved are W 1 =2200 J, W 2 =-825J, W 3 = - 1100 J and W4
respectively.
(a) Find the value of W4 . (b) What is the efficiency of the cycle ?
Q 14. One mole of an ideal monoatomic gas is taken round the cyclic process ABCA as shown in figure.
Calculate:
(a) The work done by the gas.
(b) The heat rejected by the gas in the path CA and heat absorbed in the path AB.
(c) The net heat absorbed by the gas in the path BC.
(d) The maximum temperature attained by the gas during the cycle.
Q 15. Two moles of helium gas undergo a cyclic process as shown in figure. Assuming the gas to be
ideal, calculate the following quantities in this process.
(a) The net change in the heat energy. (b) The net work done.
(c) The net change in internal energy.
Q 16. n moles of a monoatomic gas are taken around in a cyclic process consisting of four processes
along ABCDA as shown. All the lines on the P-V diagram have slope of magnitude Po / Vo . The
pressure at A and C is P0 and the volumes at A and C are V0/2 and 3V0/2 respectively . Calculate
the percentage efficiency of the cycle.
Q 17. A system is taken around the cycle shown in figure from state a to state b and then back to state a.
The absolute value of the heat transfer during one cycle is 7200 J. (a) Does the system absorb or
liberate heat when it goes around the cycle in the direction shown in the figure ? (b) What is the
work W done by the system in one cycle ? (c) If the system goes around the cycle in a counter-
clock wise direction, does it absorb or liberate heat in one cycle? What is the magnitude of the
heat absorbed or liberated in one counterclockwise cycle ?
Page 3
Exercises
For JEE Main
Subjective Questions
First Law of Thermodynamics
Q 1. In a certain chemical process, a lab technician supplies 254 J of heat to a system. At the same time,
73 J of work are done on the system by its surroundings. What is the increase in the internal
energy of the system?
Q 2. One mole of an ideal monoatomic gas is initially at 300 K. Find the final temperature if 200 J of
heat are added as follows :
(a) at constant volume, (b) at constant pressure.
Q 3. Show how internal energy U varies with T in isochoric, isobaric and adiabatic process?
Q 4. A closed vessel 10 L in volume contains a diatomic gas under a pressure of 10
5
N/ m
2
. What
amount of heat should be imparted to the gas to increase the pressure in the vessel five times ?
Q 5. A diatomic ideal gas is heated at constant volume until its pressure becomes three times. It is again
heated at constant pressure until its volume is doubled. Find the molar heat capacity for the whole
process.
Q 6. Two moles of a certain gas at a temperature T0 = 300 K were cooled isochorically so that the
pressure of the gas got reduced 2 times. Then as a result of isobaric process, the gas is allowed to
expand till its temperature got back to the initial value. Find the total amount of heat absorbed by
gas in this process.
Q 7. Five moles of an ideal monoatomic gas with an initial temperature of 127° C expand and in the
process absorb 1200 J of heat and do 2100 J of work . What is the final temperature of the gas ?
Q 8. An ideal gas expands while the pressure is kept constant. During this process, does heat flow into
the gas or out of the gas? Justify your answer.
Q 9. Find the change in the internal energy of 2 kg of water as it is heated from 0° C to 4° C. The
specific heat capacity of water is 4200J/kg –K and its densities at 0° C and 4°C are 999.9 kg/m
3
and 1000 kg/m
3
respectively. Atmospheric pressure = 10
5
Pa.
Q 10. Calculate the increase in the internal energy of 10 g of water when it is heated from 0° C to 100° C
and converted into steam at 100 kPa. The density of steam = 0.6 kg/m
3
. Specific heat capacity of
water = 4200 J/kg-° Cand the latent heat of vaporization of water = 2.5 × 10
6
J/kg.
Q 11. One gram of water (1 cm
3
) becomes 1671cm of steam when boiled at a constant pressure of 1 atm
(1.013 × 10
5
Pa). The heat of vaporization at this pressure is Lv = 2.256 × 10
6
J/kg. Compute (a)
the work done by the water when it vaporizes and (b) its increase in internal energy.
Q 12. A gas in a cylinder is held at a constant pressure of 2.30 × 10
5
Pa and is cooled and compressed
from 1.70 m
3
to 1.20 m
3
. The internal energy of the gas decreases by 1.40 × 10
5
J. (a) Find the
work done by the gas. (b) Find the absolute value | Q | of the heat flow into or out of the gas and
state the direction of the heat flow. (c) Does it matter whether or not the gas is ideal ? Why or why
not?
Cyclic Process and Efficiency of Cycle
Q 13. An ideal gas is taken through a cyclic thermodynamic process through four steps. The amounts of
heat involved in these steps are Q1 =5960J, Q2 =-5585J,Q3 = -2980J and Q4 = 3645 J respectively.
The corresponding quantities of work involved are W 1 =2200 J, W 2 =-825J, W 3 = - 1100 J and W4
respectively.
(a) Find the value of W4 . (b) What is the efficiency of the cycle ?
Q 14. One mole of an ideal monoatomic gas is taken round the cyclic process ABCA as shown in figure.
Calculate:
(a) The work done by the gas.
(b) The heat rejected by the gas in the path CA and heat absorbed in the path AB.
(c) The net heat absorbed by the gas in the path BC.
(d) The maximum temperature attained by the gas during the cycle.
Q 15. Two moles of helium gas undergo a cyclic process as shown in figure. Assuming the gas to be
ideal, calculate the following quantities in this process.
(a) The net change in the heat energy. (b) The net work done.
(c) The net change in internal energy.
Q 16. n moles of a monoatomic gas are taken around in a cyclic process consisting of four processes
along ABCDA as shown. All the lines on the P-V diagram have slope of magnitude Po / Vo . The
pressure at A and C is P0 and the volumes at A and C are V0/2 and 3V0/2 respectively . Calculate
the percentage efficiency of the cycle.
Q 17. A system is taken around the cycle shown in figure from state a to state b and then back to state a.
The absolute value of the heat transfer during one cycle is 7200 J. (a) Does the system absorb or
liberate heat when it goes around the cycle in the direction shown in the figure ? (b) What is the
work W done by the system in one cycle ? (c) If the system goes around the cycle in a counter-
clock wise direction, does it absorb or liberate heat in one cycle? What is the magnitude of the
heat absorbed or liberated in one counterclockwise cycle ?
Q 18. A thermodynamic system undergoes a cyclic process as shown in figure. The cycle consists of two
closed loops, loop I and loop II.
(a) Over one complete cycle, does the system do positive or negative work ?
(b) In each of loops I and II, is the net work done by the system positive or negative ?
(c) Over one complete cycle, does heat flow into or out of the system ?
(d) In each of loops I and II, does heat flow into or out of the system ?
Q 19. 1.0 k-mol of a sample of helium gas is put through the cycle of operations shown in figure. BC is
an isothermal process and PA = 1.00 atm ,VA =22.4m
3
,PB =2.00 atm. What are TA, TB and VC ?
Q 20. For the thermodynamic cycle shown in figure find
(a) net output work of the gas during the cycle, (b) net heat flow into the gas per cycle.
Q 21. The density ( ?)
versus pressure (P) graph of an ideal gas (monoatomic) undergoing a cyclic
process is shown in figure. The gas taken has molecular mass M and one mole of gas is taken.
Page 4
Exercises
For JEE Main
Subjective Questions
First Law of Thermodynamics
Q 1. In a certain chemical process, a lab technician supplies 254 J of heat to a system. At the same time,
73 J of work are done on the system by its surroundings. What is the increase in the internal
energy of the system?
Q 2. One mole of an ideal monoatomic gas is initially at 300 K. Find the final temperature if 200 J of
heat are added as follows :
(a) at constant volume, (b) at constant pressure.
Q 3. Show how internal energy U varies with T in isochoric, isobaric and adiabatic process?
Q 4. A closed vessel 10 L in volume contains a diatomic gas under a pressure of 10
5
N/ m
2
. What
amount of heat should be imparted to the gas to increase the pressure in the vessel five times ?
Q 5. A diatomic ideal gas is heated at constant volume until its pressure becomes three times. It is again
heated at constant pressure until its volume is doubled. Find the molar heat capacity for the whole
process.
Q 6. Two moles of a certain gas at a temperature T0 = 300 K were cooled isochorically so that the
pressure of the gas got reduced 2 times. Then as a result of isobaric process, the gas is allowed to
expand till its temperature got back to the initial value. Find the total amount of heat absorbed by
gas in this process.
Q 7. Five moles of an ideal monoatomic gas with an initial temperature of 127° C expand and in the
process absorb 1200 J of heat and do 2100 J of work . What is the final temperature of the gas ?
Q 8. An ideal gas expands while the pressure is kept constant. During this process, does heat flow into
the gas or out of the gas? Justify your answer.
Q 9. Find the change in the internal energy of 2 kg of water as it is heated from 0° C to 4° C. The
specific heat capacity of water is 4200J/kg –K and its densities at 0° C and 4°C are 999.9 kg/m
3
and 1000 kg/m
3
respectively. Atmospheric pressure = 10
5
Pa.
Q 10. Calculate the increase in the internal energy of 10 g of water when it is heated from 0° C to 100° C
and converted into steam at 100 kPa. The density of steam = 0.6 kg/m
3
. Specific heat capacity of
water = 4200 J/kg-° Cand the latent heat of vaporization of water = 2.5 × 10
6
J/kg.
Q 11. One gram of water (1 cm
3
) becomes 1671cm of steam when boiled at a constant pressure of 1 atm
(1.013 × 10
5
Pa). The heat of vaporization at this pressure is Lv = 2.256 × 10
6
J/kg. Compute (a)
the work done by the water when it vaporizes and (b) its increase in internal energy.
Q 12. A gas in a cylinder is held at a constant pressure of 2.30 × 10
5
Pa and is cooled and compressed
from 1.70 m
3
to 1.20 m
3
. The internal energy of the gas decreases by 1.40 × 10
5
J. (a) Find the
work done by the gas. (b) Find the absolute value | Q | of the heat flow into or out of the gas and
state the direction of the heat flow. (c) Does it matter whether or not the gas is ideal ? Why or why
not?
Cyclic Process and Efficiency of Cycle
Q 13. An ideal gas is taken through a cyclic thermodynamic process through four steps. The amounts of
heat involved in these steps are Q1 =5960J, Q2 =-5585J,Q3 = -2980J and Q4 = 3645 J respectively.
The corresponding quantities of work involved are W 1 =2200 J, W 2 =-825J, W 3 = - 1100 J and W4
respectively.
(a) Find the value of W4 . (b) What is the efficiency of the cycle ?
Q 14. One mole of an ideal monoatomic gas is taken round the cyclic process ABCA as shown in figure.
Calculate:
(a) The work done by the gas.
(b) The heat rejected by the gas in the path CA and heat absorbed in the path AB.
(c) The net heat absorbed by the gas in the path BC.
(d) The maximum temperature attained by the gas during the cycle.
Q 15. Two moles of helium gas undergo a cyclic process as shown in figure. Assuming the gas to be
ideal, calculate the following quantities in this process.
(a) The net change in the heat energy. (b) The net work done.
(c) The net change in internal energy.
Q 16. n moles of a monoatomic gas are taken around in a cyclic process consisting of four processes
along ABCDA as shown. All the lines on the P-V diagram have slope of magnitude Po / Vo . The
pressure at A and C is P0 and the volumes at A and C are V0/2 and 3V0/2 respectively . Calculate
the percentage efficiency of the cycle.
Q 17. A system is taken around the cycle shown in figure from state a to state b and then back to state a.
The absolute value of the heat transfer during one cycle is 7200 J. (a) Does the system absorb or
liberate heat when it goes around the cycle in the direction shown in the figure ? (b) What is the
work W done by the system in one cycle ? (c) If the system goes around the cycle in a counter-
clock wise direction, does it absorb or liberate heat in one cycle? What is the magnitude of the
heat absorbed or liberated in one counterclockwise cycle ?
Q 18. A thermodynamic system undergoes a cyclic process as shown in figure. The cycle consists of two
closed loops, loop I and loop II.
(a) Over one complete cycle, does the system do positive or negative work ?
(b) In each of loops I and II, is the net work done by the system positive or negative ?
(c) Over one complete cycle, does heat flow into or out of the system ?
(d) In each of loops I and II, does heat flow into or out of the system ?
Q 19. 1.0 k-mol of a sample of helium gas is put through the cycle of operations shown in figure. BC is
an isothermal process and PA = 1.00 atm ,VA =22.4m
3
,PB =2.00 atm. What are TA, TB and VC ?
Q 20. For the thermodynamic cycle shown in figure find
(a) net output work of the gas during the cycle, (b) net heat flow into the gas per cycle.
Q 21. The density ( ?)
versus pressure (P) graph of an ideal gas (monoatomic) undergoing a cyclic
process is shown in figure. The gas taken has molecular mass M and one mole of gas is taken.
(a) Find work done in each process.
(b) Find heat rejected by gas in one complete cycle.
(c) Find the efficiency of the cycle.
Q 22. An ideal gas goes through the cycle abc. For the complete cycle 800 J of heat flows out of the gas.
Process ab is at constant pressure and process bc is at constant volume . In process c-a, P ? V.
States a and b have temperatures Ta = 200 K and Tb = 300 K.
(a) Sketch the P-V diagram for the cycle, (b) What is the work W for the process ca ?
Q 23. A monoatomic gas is expanded adiabatically from volume V0 to 2 V 0 and then is brought back to
the initial state through an isothermal and isochoric process respectively. Plot the P-V diagram of
the complete cycle and find the efficiency of the cycle.
Solutions
1. ?U = Q - W
= 254 -(-73)= 327 J
2. (a)
? 200 =1.5 × 8.31(T f - 300)
Solving we get,
Tf = 316K
(b)
? 200 = 2.5 × 8.31(Tf - 300)
3. For all process,
4. V = constant
From PV = nRT
5. First process
V = constant
Page 5
Exercises
For JEE Main
Subjective Questions
First Law of Thermodynamics
Q 1. In a certain chemical process, a lab technician supplies 254 J of heat to a system. At the same time,
73 J of work are done on the system by its surroundings. What is the increase in the internal
energy of the system?
Q 2. One mole of an ideal monoatomic gas is initially at 300 K. Find the final temperature if 200 J of
heat are added as follows :
(a) at constant volume, (b) at constant pressure.
Q 3. Show how internal energy U varies with T in isochoric, isobaric and adiabatic process?
Q 4. A closed vessel 10 L in volume contains a diatomic gas under a pressure of 10
5
N/ m
2
. What
amount of heat should be imparted to the gas to increase the pressure in the vessel five times ?
Q 5. A diatomic ideal gas is heated at constant volume until its pressure becomes three times. It is again
heated at constant pressure until its volume is doubled. Find the molar heat capacity for the whole
process.
Q 6. Two moles of a certain gas at a temperature T0 = 300 K were cooled isochorically so that the
pressure of the gas got reduced 2 times. Then as a result of isobaric process, the gas is allowed to
expand till its temperature got back to the initial value. Find the total amount of heat absorbed by
gas in this process.
Q 7. Five moles of an ideal monoatomic gas with an initial temperature of 127° C expand and in the
process absorb 1200 J of heat and do 2100 J of work . What is the final temperature of the gas ?
Q 8. An ideal gas expands while the pressure is kept constant. During this process, does heat flow into
the gas or out of the gas? Justify your answer.
Q 9. Find the change in the internal energy of 2 kg of water as it is heated from 0° C to 4° C. The
specific heat capacity of water is 4200J/kg –K and its densities at 0° C and 4°C are 999.9 kg/m
3
and 1000 kg/m
3
respectively. Atmospheric pressure = 10
5
Pa.
Q 10. Calculate the increase in the internal energy of 10 g of water when it is heated from 0° C to 100° C
and converted into steam at 100 kPa. The density of steam = 0.6 kg/m
3
. Specific heat capacity of
water = 4200 J/kg-° Cand the latent heat of vaporization of water = 2.5 × 10
6
J/kg.
Q 11. One gram of water (1 cm
3
) becomes 1671cm of steam when boiled at a constant pressure of 1 atm
(1.013 × 10
5
Pa). The heat of vaporization at this pressure is Lv = 2.256 × 10
6
J/kg. Compute (a)
the work done by the water when it vaporizes and (b) its increase in internal energy.
Q 12. A gas in a cylinder is held at a constant pressure of 2.30 × 10
5
Pa and is cooled and compressed
from 1.70 m
3
to 1.20 m
3
. The internal energy of the gas decreases by 1.40 × 10
5
J. (a) Find the
work done by the gas. (b) Find the absolute value | Q | of the heat flow into or out of the gas and
state the direction of the heat flow. (c) Does it matter whether or not the gas is ideal ? Why or why
not?
Cyclic Process and Efficiency of Cycle
Q 13. An ideal gas is taken through a cyclic thermodynamic process through four steps. The amounts of
heat involved in these steps are Q1 =5960J, Q2 =-5585J,Q3 = -2980J and Q4 = 3645 J respectively.
The corresponding quantities of work involved are W 1 =2200 J, W 2 =-825J, W 3 = - 1100 J and W4
respectively.
(a) Find the value of W4 . (b) What is the efficiency of the cycle ?
Q 14. One mole of an ideal monoatomic gas is taken round the cyclic process ABCA as shown in figure.
Calculate:
(a) The work done by the gas.
(b) The heat rejected by the gas in the path CA and heat absorbed in the path AB.
(c) The net heat absorbed by the gas in the path BC.
(d) The maximum temperature attained by the gas during the cycle.
Q 15. Two moles of helium gas undergo a cyclic process as shown in figure. Assuming the gas to be
ideal, calculate the following quantities in this process.
(a) The net change in the heat energy. (b) The net work done.
(c) The net change in internal energy.
Q 16. n moles of a monoatomic gas are taken around in a cyclic process consisting of four processes
along ABCDA as shown. All the lines on the P-V diagram have slope of magnitude Po / Vo . The
pressure at A and C is P0 and the volumes at A and C are V0/2 and 3V0/2 respectively . Calculate
the percentage efficiency of the cycle.
Q 17. A system is taken around the cycle shown in figure from state a to state b and then back to state a.
The absolute value of the heat transfer during one cycle is 7200 J. (a) Does the system absorb or
liberate heat when it goes around the cycle in the direction shown in the figure ? (b) What is the
work W done by the system in one cycle ? (c) If the system goes around the cycle in a counter-
clock wise direction, does it absorb or liberate heat in one cycle? What is the magnitude of the
heat absorbed or liberated in one counterclockwise cycle ?
Q 18. A thermodynamic system undergoes a cyclic process as shown in figure. The cycle consists of two
closed loops, loop I and loop II.
(a) Over one complete cycle, does the system do positive or negative work ?
(b) In each of loops I and II, is the net work done by the system positive or negative ?
(c) Over one complete cycle, does heat flow into or out of the system ?
(d) In each of loops I and II, does heat flow into or out of the system ?
Q 19. 1.0 k-mol of a sample of helium gas is put through the cycle of operations shown in figure. BC is
an isothermal process and PA = 1.00 atm ,VA =22.4m
3
,PB =2.00 atm. What are TA, TB and VC ?
Q 20. For the thermodynamic cycle shown in figure find
(a) net output work of the gas during the cycle, (b) net heat flow into the gas per cycle.
Q 21. The density ( ?)
versus pressure (P) graph of an ideal gas (monoatomic) undergoing a cyclic
process is shown in figure. The gas taken has molecular mass M and one mole of gas is taken.
(a) Find work done in each process.
(b) Find heat rejected by gas in one complete cycle.
(c) Find the efficiency of the cycle.
Q 22. An ideal gas goes through the cycle abc. For the complete cycle 800 J of heat flows out of the gas.
Process ab is at constant pressure and process bc is at constant volume . In process c-a, P ? V.
States a and b have temperatures Ta = 200 K and Tb = 300 K.
(a) Sketch the P-V diagram for the cycle, (b) What is the work W for the process ca ?
Q 23. A monoatomic gas is expanded adiabatically from volume V0 to 2 V 0 and then is brought back to
the initial state through an isothermal and isochoric process respectively. Plot the P-V diagram of
the complete cycle and find the efficiency of the cycle.
Solutions
1. ?U = Q - W
= 254 -(-73)= 327 J
2. (a)
? 200 =1.5 × 8.31(T f - 300)
Solving we get,
Tf = 316K
(b)
? 200 = 2.5 × 8.31(Tf - 300)
3. For all process,
4. V = constant
From PV = nRT
5. First process
V = constant
Pressure becomes three times.
Therefore temperature also becomes three times.
(Tf = 3Ti)
Second process
P = constant
Volume is doubled. So temperature also becomes two time.
(T'f = 6Ti)
6. First Process
V = constant
Pressure becomes half. So, temperature also becomes half.
= - 300 C V
Second Process
P = constant
= 2CP(300-150) = 300 CP
Q = Q1 + Q2
= 300(CP - CV) = 300 R
= 300 × 8.31 = 2493 J
7.
Tf = 385 K
8. P = constant
As the gas expands V increases. So, T also increases. Hence is positive. Therefore in the
expression,
Q is positive.
9.
Read More
FAQs on DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer - DC Pandey Solutions for JEE Physics
| 1. What is calorimetry? |  |
Ans. Calorimetry is the branch of science that deals with the measurement of heat transfer during physical and chemical processes. It involves measuring the heat gained or lost by a substance to determine its specific heat capacity or heat of reaction.
| 2. How is heat transfer related to calorimetry? | |
Ans. Heat transfer is the process by which thermal energy is exchanged between two objects or systems. In calorimetry, heat transfer is measured using a calorimeter, which is an insulated device designed to minimize heat exchange with the surroundings. By measuring the temperature change of a substance inside the calorimeter, the heat transfer can be determined.
| 3. What is the significance of calorimetry in JEE Main Physics? | |
Ans. Calorimetry is an important topic in JEE Main Physics as it helps in understanding the principles of heat transfer and energy conservation. Questions related to calorimetry often appear in the exam, testing the students' understanding of specific heat capacity, latent heat, and heat of reaction.
| 4. How can DC Pandey's book help in preparing for calorimetry and heat transfer questions in JEE Main? | |
Ans. DC Pandey's book provides comprehensive explanations and solved examples related to calorimetry and heat transfer. It covers the fundamental concepts and formulas required to solve numerical problems in this topic. Practicing questions from the book can help in developing problem-solving skills and improving exam performance.
| 5. What are some common applications of calorimetry in real-life situations? | |
Ans. Calorimetry has various applications in real-life situations. It is used in food industry to determine the calorie content of food products. It is also used in medical research to measure the heat generated by living organisms. Additionally, it is used in engineering to study heat transfer in various systems, such as heat exchangers and refrigeration systems.
Related Exams
About this Document
|
4.82/5 Rating |
|
Dec 26, 2024 Last updated |
Document Description: DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer for JEE 2024 is part of DC Pandey Solutions for JEE Physics preparation.
The notes and questions for DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer have been prepared according to the JEE exam syllabus. Information about DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer covers topics
like and DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer Example, for JEE 2024 Exam. Find important definitions, questions, notes, meanings, examples, exercises and tests below for DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer.
Introduction of DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer in English is available as part of our DC Pandey Solutions for JEE Physics
for JEE & DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer in Hindi for DC Pandey Solutions for JEE Physics course.
Download more important topics related with notes, lectures and mock test series for JEE
Exam by signing up for free. JEE: DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics
Description
Full syllabus notes, lecture & questions for DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics - JEE | Plus excerises question with solution to help you revise complete syllabus for DC Pandey Solutions for JEE Physics | Best notes, free PDF download
Information about DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer
In this doc you can find the meaning of DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer defined & explained in the simplest way possible. Besides explaining types of
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer theory, EduRev gives you an ample number of questions to practice DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer tests, examples and also practice JEE
tests
|
Explore Courses for JEE exam
|
|
Signup for Free!
Signup to see your scores go up within 7 days! Learn & Practice with 1000+ FREE Notes, Videos & Tests.
Related Searches
ppt
,DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics
,Extra Questions
,Free
,DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics
,study material
,Summary
,Objective type Questions
,practice quizzes
,Sample Paper
,DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer | DC Pandey Solutions for JEE Physics
,video lectures
,Important questions
,shortcuts and tricks
,MCQs
,Exam
,Semester Notes
,mock tests for examination
,past year papers
,Previous Year Questions with Solutions
,Viva Questions
;
Additional Information about DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer for JEE Preparation
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer Free PDF Download
The DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer is an invaluable resource that delves deep into the core of the JEE exam.
These study notes are curated by experts and cover all the essential topics and concepts, making your preparation more efficient and effective.
With the help of these notes, you can grasp complex subjects quickly, revise important points easily,
and reinforce your understanding of key concepts. The study notes are presented in a concise and easy-to-understand manner,
allowing you to optimize your learning process. Whether you're looking for best-recommended books, sample papers, study material,
or toppers' notes, this PDF has got you covered. Download the DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer now and kickstart your journey towards success in the JEE exam.
Importance of DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer
The importance of DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer cannot be overstated, especially for JEE aspirants.
This document holds the key to success in the JEE exam.
It offers a detailed understanding of the concept, providing invaluable insights into the topic.
By knowing the concepts well in advance, students can plan their preparation effectively.
Utilize this indispensable guide for a well-rounded preparation and achieve your desired results.
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer Notes
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer Notes offer in-depth insights into the specific topic to help you master it with ease.
This comprehensive document covers all aspects related to DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer.
It includes detailed information about the exam syllabus, recommended books, and study materials for a well-rounded preparation.
Practice papers and question papers enable you to assess your progress effectively.
Additionally, the paper analysis provides valuable tips for tackling the exam strategically.
Access to Toppers' notes gives you an edge in understanding complex concepts.
Whether you're a beginner or aiming for advanced proficiency, DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer Notes on EduRev are your ultimate resource for success.
DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer JEE Questions
The "DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer JEE Questions" guide is a valuable resource for all aspiring students preparing for the
JEE exam. It focuses on providing a wide range of practice questions to help students gauge
their understanding of the exam topics. These questions cover the entire syllabus, ensuring comprehensive preparation.
The guide includes previous years' question papers for students to familiarize themselves with the exam's format and difficulty level.
Additionally, it offers subject-specific question banks, allowing students to focus on weak areas and improve their performance.
Study DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer on the App
Students of JEE can study DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer alongwith tests & analysis from the EduRev app,
which will help them while preparing for their exam. Apart from the DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer,
students can also utilize the EduRev App for other study materials such as previous year question papers, syllabus, important questions, etc.
The EduRev App will make your learning easier as you can access it from anywhere you want.
The content of DC Pandey Solutions (JEE Main): Calorimetry and Heat Transfer is prepared as per the latest JEE syllabus.
|
© EduRev
|
Education Revolution
|
|
Signup to see your scores
go up within 7 days!
Access 1000+ FREE Docs, Videos and Tests
Takes less than 10 seconds to signup